JUKI贴片机错误代码.pdf - 第420页
E3039 “ Optimization was no t performed. “ " 没有执行优化。 " E3040 Number of ci rcuits on one P WB exceeds limit (400). " 在一块板上的 电路数量超过限制 (1200) 。 " [Cause] Appears if with more t han 100 circuit-divisions …
Appears if any invalid value (exceeding the number of leads) is specified for the first lack number
during vision data editing.
[Deal]
Check the entered number.
E3032 “Limits are exceeded. “
"限制超出。"
E3033 Character searched for cannot be found.
"找不到字符。"
[Cause]
Appears if the data with the specified conditions was not found during a search process.
[Deal]
Check the search conditions.
E3034 Mounting position of component in program duplicates position of component already mounted.
"在程序中组件的贴装位置复制组件的位置已经装备。"
[Cause]
Appears if the claimed position has been allocated for placement information preset during the MSL
setup.
[Deal]
Select another position.
E3035 “Another component is using the picking position of this previously mounted component. “
"贴装组件的预定选取位置正被另外一个组件使用。"
E3036 "Placement part already resides at the intended position," appears if the claimed position has been
allocated for placement information preset during the MSL setup.
"已经被预先供给的组件占用。"
[Deal]
Select another position.
E3037 Data base file cannot be found.
"没有找到数据库文件。"
[Cause]
Appears if no database resides on the directory specified during the MSL setup..
[Deal]
Make sure that the directory specified during the MSL setup contains any database.
E3038 “Database file is being used by another EXE, so it could not be read in. “
"数据库文件被另一个 EXE 文件使用，不能读入。"
E3039 “Optimization was not performed. “
"没有执行优化。"
E3040 Number of circuits on one PWB exceeds limit (400).
"在一块板上的 电路数量超过限制(1200)。"
[Cause]
Appears if with more than 100 circuit-divisions (n x n) is specified in the multi-chamfer matrix for the
base construction of the PWB data.
[Deal]
Decrease the circuit divisions (n x n) to 100 or less.
E3041 Exterior shape of circuit PWB or circuit has not been set.
"电路基板或电路的外部形状未设置。"
[Cause]
Appears if a bad mark is entered with the PWB or circuit outside dimension not defined for the PWB
data.
[Deal]
Before entering a bad mark, specify the PWB or circuit outside dimension.
E3042 Pick data are full.
"拾取数据已满。"
[Cause]
Appears if absorption data exceeding the maximum is specified.
[Deal]
Decrease the absorption data to the maximum or less.
E3043 There are incomplete pick data for this previously mounted component.
"预定的贴片组件上有不完全选取数据。"
[Cause]
Appears if any placement information incomplete placement data is loaded for the mounting data.
[Deal]
Complete the relative placement information during the MSL setup.
E3044 “Production EXE reservation for this file is in progress. “
"正在进行文件产生 EXE."
E3045 “Optimization is completed. “
"优化已经完成。"
W3046 Deletion will be performed . Is this OK?
"执行删除，确定吗？"
[Explanation]
Appears if cutting is selected for each screen.
E3047 “Optimization failed. “
"优化失败。"
E3048 “Optimization was interrupted. “
"优化被终止。"
E3049 “Mismatch occured between line configuration and program data. “
"在线外形和程序数据之间不匹配。"
E3050 Program will be terminated.
"将退出编辑程序。"
[Explanation]
Appears if the program editing forced an abnormal ending after starting.
W3051 Dispenser X blow point is out of PWB.
"X 打击点在基板的外部。"
[Explanation]
Appears if the start position for dummy punching deviates from the PWB.
W3052 Dispenser Y blow point is out of PWB.
"Y 打击点在基板的外部"
[Explanation]
Appears if the start position for dummy punching deviates from the PWB.
W3053 Both X and Y dispenser blow count is set to 0, dispenser blow will be disabled. Are you sure?
"X 和 Y 分配的打击数都设置成 0，分配打击将取消，确定吗？"
[Explanation]
Appears if 0 is specified for both the numbers of dummy punching operations, X and Y, and the OK
button is pressed.
W3055 Data is incomplete. Would you like to save?
"数据不完整，要保存吗？"
[Explanation]
Appears if saving incomplete data is tried.
E3056 Same component name is already in component data.
"在组件数据中已有同样的组件名。"
[Cause]
Appears if the name of an existing part within the program editing is requested when retrieving a
database listing.
[Deal]