JUKI贴片机错误代码.pdf - 第257页

E620003 “ Area sensor perceived .” “ 发现超 出范围。 ” [ 原因 ] 因某种理由范围传感器起作用而引起 错误。 [ 解决 ] 请解除范围传感器起作用的原因。 E620004 “ Feeder sensor detected .” “ 发现传 送带浮动。 ” [ 原因 ] 因某种理由传送带浮动传感器起作用 而引起错误。 [ 解决 ] 请解除传送带浮动传感器起作用的原 因。 E620005 “ X l…

100%1 / 464
E611301 “An error occurred when COMRES response receive. (L1-head)”
“ 接受 COMRES 应答出错。(L1 Head) “
E612301 “An error occurred when COMRES response receive. (L2-head)”
“ 接受 COMRES 应答出错。(L2 Head) “
E613301 “An error occurred when COMRES response receive. (L3-head)”
“ 接受 COMRES 应答出错。(L3 Head) “
E614301 “An error occurred when COMRES response receive. (L4-head)”
“ 接受 COMRES 应答出错。(L4 Head) “
E615301 “An error occurred when COMRES response receive. (R1-head)”
“ 接受 COMRES 应答出错。(R1 Head) “
E616301 “An error occurred when COMRES response receive. (R2-head)”
“ 接受 COMRES 应答出错。(R2 Head) “
E617301 “An error occurred when COMRES response receive. (R3-head)”
“ 接受 COMRES 应答出错。(R3ead) “
E618301 “An error occurred when COMRES response receive. (R4-head) “
“ 接受 COMRES 应答出错。(R4 Head) “
第六章 异步
[异步、图像、球识别、外形引脚测量、MTC、MTS、MTD]
E620001”Emergency stop.”
“被紧急停止。”
[原因]
主机的<紧急停止>按钮被按下。
[解决]
请释放主机的<紧急停止>。
E620002 “Cover opened.”
“机盖被打开。”
[原因]
主机的机盖被开着的状态。
[解决]
以慢速移动时，请注意安全等。
以快速移动时，请关上机盖。
E620003 “Area sensor perceived.”
“发现超出范围。”
[原因]
因某种理由范围传感器起作用而引起错误。
[解决]
请解除范围传感器起作用的原因。
E620004 “Feeder sensor detected.”
“发现传送带浮动。”
[原因]
因某种理由传送带浮动传感器起作用而引起错误。
[解决]
请解除传送带浮动传感器起作用的原因。
E620005 “X limit sensor perceived.”
“X 轴移动超出界限。”
[原因]
如果 X 轴的界限传感器上面有轴时，就显示此信息。
[解决]
从界限传感器上，用手动移动轴之后，请按[确定]键。
E620006 “Xr limit sensor perceived.”
“右 X 轴移动超出界限。”
[原因]
如果右 X 轴的界限传感器上面有轴时，就显示此信息。
[解决]
从界限传感器上，用手动移动轴之后，请按[确定]键。
E620007 “Y limit sensor perceived.”
“Y 轴移动超出界限。”
[原因]
如果 Y 轴的界限传感器上面有轴时，就显示此信息。
[解决]
从界限传感器上，用手动移动轴之后，请按[确定]键。
E620008 “Yc limit sensor perceived.”
“Yc 轴移动超出界限。”
[原因]
如果 Yc 轴的界限传感器上面有轴时，就显示此信息。
[解决]
从界限传感器上用手动移动轴之后，请按[确定]键。
E620009 X driver alarmed. <%s>“
“X 轴驱动警报”
[Cause]
An abnormal matter happened to the X axis driver.
X 轴驱动器发生错误。
[Treatment]
Please perform proper treatments that are corresponding to the error numbers shown below. If the
treatments are not enough, please take a note of the error No. and the details (* side DATA1= **
DATA2= ** DATA3= **) and contact our technical service dept. for information.
根据以下显示的错误编号进行相应处理。
即使进行相应处理也发生错误时，请记好错误代码和详细代码(＊side DATA1= ＊＊
DATA2= ＊＊ DATA3=＊＊)，与代理点或本公司技朮服务部联系。
[相应处理]
DATA3 = 1 [over-electric current（过电流）]
If the error occurs when turning the servo on: There is a possibility of the miswiring of the motor
circuits. Please examine the wiring.
伺服一启动就发生错误：马达电路的配线故障。请检查配线。
If the error occurs while the servo is ON(the motor is vibrating): Please re-adjust the gain.
伺服运转中发生错误(马达处于震动状态)：请再调整增益。
If the error occurs when accelerating/decelerating: Please examine the inertia.
加速、减速时发生错误：请检查惯性负荷。
If the error occurs when revolving: Please examine the torque.
旋转时发生错误：请检查扭转负荷。
DATA3 = 2 [over-load（超负荷）]
If the error occurs when turning the servo on: There is a possibility of the miswiring of the motor
circuits. Please examine the wiring.
伺服一启动就发生错误：马达电路的配线故障。请检查配线。
If the error occurs while the servo is ON(the motor is vibrating): Please re-adjust the gain.
伺服运转中发生错误(马达处于震动状态)：请再调整增益。
If the error occurs when accelerating/decelerating: Please examine the inertia.
加速、减速时发生错误：请检查惯性负荷。
If the error occurs when revolving: Please examine the torque.
旋转时发生错误：请检查扭转负荷。
DATA3 = 3 [Driving power supply abnormality（驱动电源异常）
]
Please examine the value of electric currency that is sent to the driver from the power supply unit. If