JUKI贴片机错误代码.pdf - 第77页
Please remove the no zzle and then hit the “ OK ” but ton. I304002 ” A nozzle of %s is removed and ret urn to %s of ATC ” [Cause] The nozzle could not be re turned automatically. [Treatment] Please remove a nozzle on the…
“吸嘴信息(%s)已经存在。|是否覆盖保存？”
Q302018 “Please check if the PWB is clamped.|Would you like to continue ?”
“请检查一下基板是否已经被固定。|是否继续？”
Q302019 “Delete the nozzle data[ %s ].|Is that OK ?”
“删除被选吸嘴数据[ %s ]。|是否继续?”
Q302020 “The offset position with the preserved MTS class is used.|Is that OK ?”
“使用保存过的 MTS 安装偏差位置。|是否继续？”
I303000 “Return to home of %s”
“执行%s 的原点返回。”
[Cause]
Z axis and the Theta axis of the ? head will return to Home.
[Treatment]
Please hit the “OK” button.
I303001”Nozzle is removed from %s to ATC”
“卸下%s 的吸嘴。”
[Cause]
There is a need to remove the nozzle from the ? head.
[Treatment]
Please press “OK” button. If you hit the “OK” button, it will return the nozzle on the ? head to ATC.
I303002 “Return Z axis to Laser height position.”
“把 Z 轴高度返回到激传感器高度。 “
I304000 “Set online for MTC”
“请连接 MTC。”
[Cause]
Failed to draw tray out from MTC when teaching in the MTC shuttle pick position setting since MTC
was not online.
[Treatment]
Please make MTC online.
I304001 “Remove the nozzle from %s”
“请取下%s 的吸嘴。”
[Cause]
The nozzle could not be returned automatically since a nozzle installation error occurred while
automatically learning the ATC nozzle allocation. Please remove the nozzle on the ? head manually.
[Treatment]
Please remove the nozzle and then hit the “OK” button.
I304002”A nozzle of %s is removed and return to %s of ATC”
[Cause]
The nozzle could not be returned automatically.
[Treatment]
Please remove a nozzle on the head manually and return it to the of ATC.
I304003 “Set online for MTS”
“请连接 MTS。”
[Cause]
MTS was not online.
[Treatment]
Please make MTS online.
I304004 “Please close the door of MTS”
“请关闭 MTS 机箱门。”
[Cause]
Failed to draw the MTS tray out since the MTS door was open.
[Treatment]
Please close the MTS door.
I304005 “Lift a head to the highest position manually.”
手动提高 Head 的高度。”
E316001 “Memory allocation error”
“内存分配错误。”
[Cause]
The working space can not be saved.
[Treatment]
Please add some more memory available to save the working space.
E316002 “Shared memory open error”
“打开共享内存错误。”
[Cause]
The shared memory could not be open.
[Treatment]
Please shut down the your machine and re-start it.
E316011 “There is no input character”
“没有输入字符。”
[Cause]
There was no character when you hit Enter key to define characters.
[Treatment]
Please enter characters.
E316012 “Input character has irregularities”
“输入了非法字符。”
[Cause]
The letter strings had irregularities when defining the input.
[Treatment]
Please enter proper characters.
E316013 “Input value exceeds predetermined data range”
“输入值超过范围。”
[Cause]
The value when defining the input exceeded the input range.
[Treatment]
Please enter the values that are within the range.
E316021 “Return to home has not yet been completed”
“尚未结束原点返回。”
[Cause]
The axis has not yet been returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E316022 “Servo is in the free state”
“伺服处于不使用状态。”
[Cause]
The axis could not move since the servo is not locked.
[Treatment]
Please lock the servo with S-FREE switch.
E316031 “Selected device is not install. Please reselect other device on HOD”
“被选设备尚未安装。|请重新选择其它设备。”
[Cause]
You could not go into the teaching mode since the device selected by HOD has not been installed.
[Treatment]
Please reselect the device which is currently installed.
W316041 “There is no ATC that is allocated with nozzle. Allocate nozzle to ATC when setting up the
machine”