JUKI贴片机错误代码.pdf - 第132页
E510016 “ Failed in t he reception of the response from the Trans-driver ” “ 接收传送驱动器应答失败。 ” [Cause] The software did not g et started properly. [Treatment] Please turn off the power supply of t he machine and reboot it. …
E510010 “Failed in the mail check”
“检查邮件失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510011 “Failed in the mail reception”
“接收邮件失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510012 “Failed in the opening of the mail of the production-control”
“打开生产管理邮件失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510013 “Failed in the transmission of the mail to the production-control”
“往生产管理发送邮件失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510014 “Failed in the opening of the command of the Trans-driver”
“打开传送驱动命令失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510015 “Failed in the transmission of the command to the Trans-driver”
“往传送驱动器发送命令失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510016 “Failed in the reception of the response from the Trans-driver”
“接收传送驱动器应答失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510017 “Failed in the opening of the command of the sub-scheduler”
“打开次调度程序失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510018 “Failed in the transmission of the command to the sub-scheduler”
“往次调度程序发送命令失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510019 “Failed in the reception of the response from the sub-scheduler”
“接收次调度程序应答失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510020 “Failed in the opening of the command of the XY-robot”
“打开 XY-Robot 命令失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510021 “Failed in the transmission of the command to the XY-robot”
“给 XY-Robot 发送命令失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510022 “Failed in the reception of the response from the XY-robot”
“接收 XY-Robot 应答失败。”
[Cause]
The software did not get started properly.
[Treatment]
Please turn off the power supply of the machine and reboot it.
E510023 “It is algorithm change error.”
“变更测量方法(Algorithm)失败。”
E510024 “The part abandonment is abnormal.”
“废弃组件失败。”
E510025 “It is image taking picture error.”
“图像的摄像发生错误。”
E510026 “All circuit bad mark was detected.”
“发现全电路的坏板标记。”
E510027 “It is a trans-driver system error.”
“传送驱动系统发生错误。”
E510028 “Since production control is unusual, production is forced to terminate.”
“因生产控制发生错误，强行退出生产。”
E510101 “The error occurred by the Tombstone”
“芯片站立出错。”
E510102 “The error occurred by the Component fall”
“发生组件脱落。”
E510103 “The error occurred by the Verify.”
“发生数值检查错误。”
E510104 “Failed in the Illrgal component picking(MTC).”
“组件吸取（MTC）出错。”
E510105 “Failed in the Component direction.”
“组件方向出错。”
E510106 “The error occurred by the Feeder pitch gap.”
“送料间距出错。”
E510107 “Failed in the Unplaced”