JUKI贴片机错误代码.pdf - 第293页

E631084 “ Out line recognition error: Horizont al/vertical distance betwee n marks is deviated by 0.5-m m or more from the set value .” “ 外形识 别错误 : 上下左右标记间距大于 +-0.5mm ” E631085 “ Out line recognition error: Com ponent re…

100%1 / 464
E631062 “ All Balls recognition error: Uppermost/Lowermost ball rows are not paralleled (tilted +/-3 degrees
or more).”
“所有球识别错误:球上下边倾斜度大于 3 度”
E631063 “ All Balls recognition error: Leftmost/Rightmost ball columns are not paralleled (tilted +/-3 degrees
or more).”
“所有球识别错误:球左右边倾斜度大于 3 度”
E631064 “ All Balls recognition error: Distance between uppermost/lowermost ball rows is too large
(half-pitch larger).”
“所有球识别错误:球上下边距离大于半个间距”
E631065 “ All Balls recognition error: Distance between leftmost/rightmost ball column is too large
(half-pitch larger).”
“所有球识别错误:球左右边距离大于半个间距”
E631066 “ All Balls recognition error: Cannot create areas to inspect balls.”
“所有球识别错误:没有指定球检查范围。”
E631067 “ All Balls recognition error: Ball variant inspection error”
“所有球识别错误:球变形检查错误”
E631068 “ All Balls recognition error: Ball diameter inspection error”
“所有球识别错误:球直径检查错误”
E631069 “ All Balls recognition error: Ball brightness error”
“所有球识别错误:球亮度检查错误”
E631070 “ All Balls recognition error: Ball existence inspection error”
“所有球识别错误:检查球存在状况错误”
E631080 “ Outline recognition error: No component”
“外形识别错误:组件不存在”
E631081 “ Outline recognition error: Component size error”
“外形识别错误:组件大小错误”
E631082 “ Outline recognition error: Cannot find patterns within detection frame.”
“外形识别错误:检查窗口内不存在对象样品”
E631083 “ Outline recognition error: An corner angle of the IC mark square is deviated by one or more
degrees from a right angle.”
“外形识别错误:与 IC 标记的倾斜度超过 1 度”
E631084 “ Outline recognition error: Horizontal/vertical distance between marks is deviated by 0.5-mm or
more from the set value.”
“外形识别错误:上下左右标记间距大于+-0.5mm”
E631085 “ Outline recognition error: Component recognition error (analyze code for the details).”
“外形识别错误:组件错误（详细内容请参考代码解释）”
E631100 “ Multi lead recognition error: Detected lead bend.”
“多引脚识别错误:引脚弯曲错误”
E631101 “ Multi lead recognition error: Detect lead length error.”
“多引脚识别错误:引脚长度错误”
E631102 “ Multi lead recognition error: Lead pitch error”
“多引脚识别错误:引脚间距错误”
E631103 “ Multi lead recognition error: Detected leads are fewer than specified.”
“多引脚识别错误:引脚数少于设置值”
E631104 “ Multi lead recognition error: Detected leads are more than specified.”
“多引脚识别错误:引脚数多于设置值”
E631105 “ Multi lead recognition error: No leads are detected.”
“多引脚识别错误:没有发现引脚”
E631106 “ Multi lead recognition error: Detected lead count is 1 to 3.”
“多引脚识别错误:只有 1-3 个引脚”
E631107 “ Multi lead recognition error: Cannot position.”
“多引脚识别错误:不能确定组件位置”
E631108 “ Multi lead recognition error: Cannot detect leads.”
“多引脚识别错误:不能检测引脚”
E631120 “ Random ball recognition error: Ball pitch error”
“任意球识别错误:球间距错误”
E631121 “ Random ball recognition error: Ball variant inspection error”
“任意球识别错误:球变形检查错误”
E631122 “ Random ball recognition error: Ball diameter-inspection error”
“任意球识别错误:球直径检查错误”
E631123 “ Random ball recognition error: Ball existence inspection (diameter) error.”
“任意球识别错误:检查球是否存在(直径)出错”
E631124 “ Random ball recognition error: Ball existence inspection (brightness) error.”
“任意球识别错误:检查球是否存在(亮度)出错”
E631125 “ Random ball recognition error: Too few samples for ball existence inspection (brightness).”
“任意球识别错误:检查球是否存在(亮度)的样品数偏少”
E631140 “ Ball inspection error: Ball detection error”
“球检查错误:球检查错误”
E631141 “ Ball inspection error: Ball matrix size error”
“球检查错误:球矩阵大小错误”
E631142 “ Ball inspection error: Ball count error”
“球检查错误:球数错误”
E631143 “ Ball inspection error: Ball diameter error”
“球检查错误:球直径错误”
E631144 “ Ball inspection error: Error in getting brightness reference”
“球检查错误:亮度基准取得错误”
E631145 “ Ball inspection Error: Brightness characteristics error”
“球检查错误:亮度特性错误”
E631160 “ Outline measurement error: Component tilt is too large.”
“外形测量错误:组件过于倾斜”
E631161 “ Outline measurement error: Component size is too large.”
“外形测量错误:组件尺寸过大”
E631162 “ Outline measurement error: Component size is too small.”
“外形测量错误:组件尺寸过小”
E631163 “ Outline measurement error: Cannot find a component.”
“外形测量错误:组件不存在”
E631170 “ Lead measurement error: Unknown lead pitch”
“引脚测试错误:不是适当的引脚间距”
E631171 “ Lead measurement error: Cannot detect leads.”
“引脚测试错误:没有引脚”
E631180 “ Template matching error: A similar pattern is found in the upper part of the searched area.”
“ 模板自动取得错误:因上面有类似的模式”
[Cause]