JUKI贴片机错误代码.pdf - 第155页

E521080 “ Laser Error:(LEFT_BLOCKED) | T he left edge winow is blocked .” “ 激光错误 :(LEFT_BL OCKED) | 左窗口被赌塞错误。 ” E521081 “ Laser Error: (RIGHT_BLOCKED) | The right edge window is blocked .” “ 激光错误 :(RIGHT_BLOCKED) | 右窗口被赌…

100%1 / 464
E521084 “Laser Error:(DUP_START) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(DUP_START) |固件从传感器 EEPROM 读取数据中发现错误。”
E521085 “Laser Error:(NO_EEPROM_SOD) | The firmware found an error while reading the sensor
EEPROM.”
“激光错误:(NO_EEPROM_SOD) |固件从传感器 EEPROM 读取数据中发现错误。”
E521086 “Laser Error:(BAD_PARM) | An invalid parameter was specified for a command.”
“激光错误:(BAD_PARM) |命令中发现无效的参数。”
E521087 “Laser Error:(BAD_DATA) | Invalid data was detected.”
“激光错误:(BAD_DATA) |发现无效数据。”
E521100 “Laser Error:(UNITS_NOT_SET) | Requested Initialzation was not done.”
“激光错误:(UNITS_NOT_SET) |未初始化状态下，被接受命令错误。”
E521102 “Laser Error:(INVALID_ALG) | The alogrithm specified for the mesurement is invalid.”
“激光错误:(INVALID_ALG) |错误的测量方法。”
E521064 “Laser Error 　(NO_PART) | The shadow was undetectable during measurement.”
“激光错误:(NO_PART) | 测量中检测不到阴影 “
E521065 “Laser Error:(TOOL_SLOW) | The MCM processor was unable to keep up with the frame rate.”
“激光错误:(TOOL_SLOW) |MCM 处理器不能跟上测量速度。”
E521067 “Laser Error:(ABORTED) | The MCM recived a command that aborted.”
“激光错误:(ABORTED) |MCM 被接受强行停止测量命令。”
E521070 “Laser Error:(ALG_ERR) | The firmware detected a state that should never happen.”
“激光错误:(ALG_ERR) |固件发现了不应该发生的状况。”
E521075 “Laser Error:(PRV_ERR) | During SWEEP_CMD error occuerd during next mesurement.”
“激光错误:(PRV_ERR) |检查端点(Peak)中发现前一次的端点检查错误。”
E521077 “Laser Error:(WIDE_ERR) | The gray-scale edge on the detector did not have enough contrast to
finde actual component edge.”
“激光错误:(WIDE_ERR) |检查组件间距中，发现组件间距不够长。”
E521078 “Laser Error:(SMALL_WIN) | The window parameters specify a window that is samll than 2000
micron.”
“激光错误:(SMALL_WIN) |被指定小于 2000 微米的窗口。”
E521079 “Laser Error:(WIN_BLOCKED) | The entire window is blocked.”
“激光错误:(WIN_BLOCKED) |窗口被赌塞错误。”
E521080 “Laser Error:(LEFT_BLOCKED) | The left edge winow is blocked.”
“激光错误:(LEFT_BLOCKED) |左窗口被赌塞错误。”
E521081 “Laser Error:(RIGHT_BLOCKED) | The right edge window is blocked.”
“激光错误:(RIGHT_BLOCKED) |右窗口被赌塞错误。”
E521082 “Laser Error:(BOTH_BLOCKED) | Both edge of window is blocked.”
“激光错误:(BOTH_BLOCKED) |左右窗口都被赌塞错误。”
E521090 “Laser Error:(TOO_FEW_FRAMES) | Error Caluculating align angle.”
“激光错误:(TOO_FEW_FRAMES) |角度计算出错。”
E521091 “Laser Error:(MIN_OUT_RANGE1) | Error Caluculating align angle.”
“激光错误:(MIN_OUT_RANGE1) |角度计算出错。”
E521092 “Laser Error:(MIN_OUT_RANGE2) | Error Caluculating align angle.”
“激光错误:(MIN_OUT_RANGE2) |角度计算出错。”
E521093 “Laser Error:(MIN_TOO_HIGH) | The Width versus angle curveis too flat.”
“激光错误:(MIN_TOO_HIGH) |因组件太小，不能确定决定组件宽度的角度。”
E521094 “Laser Error:(NO_CUTOFF1) | Error cluculating align angle.”
“激光错误:(NO_CUTOFF1) |角度计算出错。”
E521095 “Laser Error:(NO_CUTOFF2) | Error cluculating align angle.”
“激光错误:(NO_CUTOFF2) |角度计算出错。”
E521096 “Laser Error:(CONST_ANGLE) | Error cluculating align angle.”
“激光错误:(CONST_ANGLE) |角度计算出错。”
E521098 “Laser Error:(SCAN_LIMIT) | The angle exceed apecified angle limit before a minimum was
detected.”
“激光错误:(SCAN_LIMIT) |在界限角度内不能查出决定最小宽度的角度。”
E521099 “Laser Error:(OVERRUN) | Early processing was not completed before sreach for next.”
“激光错误:(OVERRUN) |发现超出限度的错误。”
E521103 “Laser Error:(LOW_BACKGROUND) | The laser intensity was too low during image chack.”
“激光错误:(LOW_BACKGROUND) |检查图像时发现激光强度过低错误。”
E521104 “Laser Error:(BAD_IMAGE_REGION) | Image check region boundaries ware not set properly.”
“激光错误:(BAD_IMAGE_REGION) |图像检查中，发现区域分界线不明确错误。”
E521105 “Laser Error:(IMG_CHK_FAIL) | Image check failed.”
“激光错误:(IMG_CHK_FAIL) |检查图像失败。”
E521106 “Laser Error:(ERR_LEVEL_TOO_LOW) | Not defined at the error level currently specified.”
“激光错误:(ERR_LEVEL_TOO_LOW) |发现定义外的错误。”
E521201 “Laser Error:Communication Link error|Abort the process.”
“激光错误:通讯错误|请关闭程序，重新启动。”
E521203 “Laser Error:Command/Response Error|Abort the process.”
“激光错误:命令/响应错误|请关闭程序，重新启动。”
E521204 “Laser Error:Check sum error”
“激光错误:检查合计错误”
E521205 “Laser Error:Reading parameter error”
“激光错误:读取参数错误”
[原因]
从激光控制基板读参数时，发生状态错误。
[解决]
关闭电源，重新启动系统。
如果重新启动系统后，还是没解决好错误时，请联系代理店或本公司技朮服务部。
E521206 “Laser Error:Data error”
“激光错误:数据错误”
[原因]
系统内部发生错误。
[解决]
关闭电源，重新启动系统。
如果重新启动系统后，还是没解决好错误时，请联系代理店或本公司技朮服务部。
E521211 “Laser Error:File Error”
“激光错误:文件错误”
[原因]
系统内部发生错误。
[解决]
关闭电源，重新启动系统。
如果重新启动系统后，还是没解决好错误时，请联系代理店或本公司技朮服务部。
E522000 “Laser Alogorithm data Error,Please check Component data.”
“组件数据的激光运算错误” [原因]
系统内部发生错误。
[解决]
关闭电源，重新启动系统。
如果重新启动系统后，还是没解决好错误时，请联系代理店或本公司技朮服务部。