JUKI贴片机错误代码.pdf - 第199页
Nozzle returning was requested to a head which does not have an y nozzles on it. A caus e is either that a nozzle is actually not on the h ead or that the laser sensor i s broken. [Treatment] 1. If there is no nozzle on …
An error occurred while Z axis (Nozzle up-and-down axis) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610022 “An error occurred while Theta axis is revolving”
“θ轴移动时发生错误。”
[Cause]
An error occurred while Theta axis (Nozzle revolving axis) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610023 “No nozzle has been assigned to the cylinder”
“圆筒上没有分配吸嘴。”
[Cause]
No nozzle has been assigned to the specified ATC.
[Treatment]
Please set nozzle(s) on ATC and perform the ATC nozzle allocation. The ATC Nozzle allocation can
be performed by selecting [Machine Setup] from the menu bar, and then [Setting Group(G)] [ATC
Nozzle Allocation(A)].
E610024 “Nozzle installation was tried with a head which already has a nozzle”
“吸嘴已被安装，可又执行安装吸嘴。”
[Cause]
Nozzle installation was tried with a head which already has a nozzle. A cause is either that a nozzle is
actually on the head or that the window of the laser sensor is dirty.
[Treatment]
If a nozzle is installed on the head.
The nozzle is likely to have been set on the head manually. Please take it off by hand.
If a nozzle is NOT installed on the head.
‧Please clean the window of the laser sensor. You can check the dirt of the window with the
following procedures. Select [Manual Control] from the menu bar, and then select [Control(C)]
[Head(H)] [Laser Control(L)]. Select a concerned laser sensor in 'Control' unit, and then select 'Image
displaying' from 'Control Item' frame. By enabling ON, an image data will be shown.
‧If the treatment1 does not work, or if the image data does not appear, there is a possibility that the
MCM board in the laser sensor is not installed properly or the sensor itself is broken. Please turn off
the power supply and see if the MCM board is installed in the sensor correctly.
E610025 “Nozzle returning was requested to a head which does not have any nozzles”
“吸嘴不存在，可执行放回吸嘴。”
[Cause]
Nozzle returning was requested to a head which does not have any nozzles on it. A cause is either that
a nozzle is actually not on the head or that the laser sensor is broken.
[Treatment]
1. If there is no nozzle on the head.
The nozzle is likely to have been taken off manually.
2. If the head has a nozzle on it.
There is a possibility that the MCM board in the laser sensor is not installed properly or the sensor
itself is broken. Please turn off the power supply and see if the MCM board is installed in the sensor
correctly.
E610026 “The gotten nozzle width does not meet that of allocated nozzle”
“测定的吸嘴宽度与设置的吸嘴宽度不一致。”
[Cause]
The outer shape of a nozzle which was gotten from ATC does not meet the outer shape of a nozzle
which is assigned in the Machine Setup. The cause is either that the nozzle were changed manually or
that the window of the laser sensor is dirty.
[Treatment]
1. If nozzles were changed manually.
Please perform the ATC nozzle allocation. The ATC Nozzle allocation can be performed by selecting
[Machine Setup] from the menu bar, and then [Setting Group(G)] [ATC Nozzle Allocation(A)].
2. If nozzles were not changed manually.
‧Please clean the window of the laser sensor. You can check the dirt of the window with the
following procedures. Select [Manual Control] from the menu bar, and then select [Control(C)]
[Head(H)] [Laser Control(L)]. Select a concerned laser sensor in 'Control' unit, and then select 'Image
displaying' from 'Control Item' frame. By enabling ON, an image data will be shown.
‧If the treatment1 does not work, or if the image data does not appear, there is a possibility that the
MCM board in the laser sensor is not installed properly or the sensor itself is broken. Please turn off
the power supply and see if the MCM board is installed in the sensor correctly.
E610027 “An error occurred when setting Laser window size”
“设置激光窗口大小发生出错。”
[Cause]
An error occurred when setting a window size to check a nozzle presence by the laser recognition
unit.
[Treatment]
There is a possibility that the laser recognition unit has a problem. You can check if it is fine or now
with the following procedures. Please select [Manual Control] from the menu bar, and then select
[Control(C)] [Head(H)] [Laser Control(L)].Select a concerned laser sensor in 'Control' unit, and then
select 'Image displaying' from 'Control Item' frame. By enabling ON, an image data will be shown. At
this point, if the image data does not get shown, please turn off the power supply and try again. If the
image data does not get shown even after the retry, MCM board in the laser sensor is not installed
properly or the sensor itself is broken. Please turn off the power supply and see if the MCM board is
installed in the sensor correctly.
E610028 “An error occurred when detecting the presence of Laser nozzle”
“检查吸嘴是否存在时发生错误。”
[Cause]
An error occurred when setting a window size to check a nozzle presence by the laser recognition
unit.
[Treatment]
There is a possibility that the laser recognition unit has a problem. You can check if it is fine or now
with the following procedures. Please select [Manual Control] from the menu bar, and then select
[Control(C)] [Head(H)] [Laser Control(L)].Select a concerned laser sensor in 'Control' unit, and then
select 'Image displaying' from 'Control Item' frame. By enabling ON, an image data will be shown. At
this point, if the image data does not get shown, please turn off the power supply and try again. If the
image data does not get shown even after the retry, MCM board in the laser sensor is not installed
properly or the sensor itself is broken. Please turn off the power supply and see if the MCM board is
installed in the sensor correctly.
E610029 “An error occurred when learning laser height of Laser nozzle”
“激光识别器测量激光高度发生错误。”
[Cause]
An error occurred when measuring a nozzle length by the laser recognition unit.
[Treatment]
There is a possibility that the laser recognition unit has a problem. You can check if it is fine or now
with the following procedures. Please select [Manual Control] from the menu bar, and then select
[Control(C)] [Head(H)] [Laser Control(L)].Select a concerned laser sensor in 'Control' unit, and then
select 'Image displaying' from 'Control Item' frame. By enabling ON, an image data will be shown. At
this point, if the image data does not get shown, please turn off the power supply and try again. If the
image data does not get shown even after the retry, MCM board in the laser sensor is not installed
properly or the sensor itself is broken. Please turn off the power supply and see if the MCM board is
installed in the sensor correctly.
E610030 “Nozzles can not be detected”
“没有发现吸嘴。”
[Cause]
No nozzle could not be found in the Nozzle presence check by laser. Nozzles are not set in the ATC.
[Treatment]
Please set nozzle(s) on ATC and perform the ATC nozzle allocation. The ATC Nozzle allocation can