JUKI贴片机错误代码.pdf - 第323页

因 DTS 是补充状态，所以 KE-2000 的往 DTS 发送的运行指令被取 消了。 [ 解决 ] 请把 DTS 恢复成生产状态之后，继续 操作。 E642315 “ DTS ERROR : Unable t o Move by Other .” “ DTS 错误 : 因为其它原因，不能运转 ” [ 原因 ] 虽然 KE-2000 机器往 DTS 发送指令， 可是从 DTS 接受到不可执行应答信息， 取消了运行要求 ( 不可执行原因确…

100%1 / 464
[解决]
请检查KE-2000机器和DTS的连接电缆。
KE-2000机器和DTS的连接是通过后侧台架(送料器台车)连接。
请首先确认，后侧台架的连接电缆是否与KE-2000机器后侧的[FEEDER CONN]
端口连接。
如果这里连接正常，请检查DTS的连接电缆和后侧台架(FEEDER连接端口)连接是否正常。
DTS连接电缆是，安装DTS的基准针位置(机器设置->使用单元->MTC/MTS使用单元
->DTS->送料器号)所对应的后侧台架插座针(送料器孔所对应的插座针标记说明在台架正
面)为起点，从左->右的方向,按P1、P2、P3电缆顺序连接。
请同时检查，在机器设置中设置的安装DTS送料器位置是否正确对准DTS的基准针位置
(MTC/MTS/使用单元中)。
E642311 “DTS ERROR : DTS Error Happened.”
“DTS错误 : DTS发生错误”
[原因]
虽然KE-2000机器往DTS发送指令，可是从DTS接受到错误应答信息，取消了运行要求。
[解决]
考虑DTS陷入异常状态。
再投入DTS的电源(如果取掉连接器，电源被切断)、
再度请初始化DTS后，继续操作。
两三次反复运行，还是发生错误的话，请与代理店或本公司技朮服务部取联系。
E642312 “DTS ERROR : Unable to Move by Initialize Incompletely.”
“DTS错误 : 因没有运行初始化，不能运转”
[原因]
因 DTS 没有进行初始化，所以 KE-2000 的往 DTS 发送的运行指令被取消了。
[解决]
请初始化DTS后，继续操作。
E642313 “DTS ERROR : Unable to Move by Opening Safety Cover.”
“DTS错误 : 因安全盖被打开，不能运转”
[原因]
因DTS安全盖被开着，所以KE-2000的往DTS发送的运行指令被取消了。
[解决]
请关闭DTS安全盖后，继续操作。
E642314 “DTS ERROR : Unable to Move by Supply.”
“DTS错误 : 在补充阶段不能运转”
[原因]
因DTS是补充状态，所以KE-2000的往DTS发送的运行指令被取消了。
[解决]
请把DTS恢复成生产状态之后，继续操作。
E642315 “DTS ERROR : Unable to Move by Other.”
“DTS错误 : 因为其它原因，不能运转”
[原因]
虽然KE-2000机器往DTS发送指令，可是从DTS接受到不可执行应答信息，取消了运行要求
(不可执行原因确定不了)。
[解决]
考虑DTS陷入异常状态。
再投入DTS的电源(如果取掉连接器，电源被切断)、再度请初始化DTS后，继续操作。两三
次反复运行，还是发生错误的话，请与代理店或本公司技朮服务部取联系。
E642321 “DTS ERROR : Setting Tray Request End Abnormally.”
“DTS错误 : 托盘设置要求错误”
[原因]
虽然KE-2000机器往DTS发送指令，可是要抽出的DTS托盘与实际托盘位置不相符(相反方
向)
[解决]
考虑DTS陷入异常状态。
再投入DTS的电源(如果取掉连接器，电源被切断)、再度请初始化DTS后，继续操作。两三
次反复运行，还是发生错误的话，请与代理店或本公司技朮服务部取联系。
E642322 “DTS ERROR : Switching Supply Request End Abnormally.”
“DTS错误 : 补充要求错误”
[原因]
虽然KE-2000机器往DTS发送补充指令，可是DTS状态切换不了补充状态。
[解决]
考虑DTS陷入异常状态。
再投入DTS的电源(如果取掉连接器，电源被切断)、再度请初始化DTS后，继续操作。两三
次反复运行，还是发生错误的话，请与代理店或本公司技朮服务部取联系。
第七章 传送基板驱动
[传送基板驱动、CVS、AWC、I/O、照明、共面性检测器、访问 VME 总线]
E650001 “PWB Conveying Error :| System Error.”
“基板传送错误 :|传送系统错误。”
W650009 “Conveying device error: | Since a PWB which interferences the check cylinder, | the cylinder can
not come up. | Please remove the PWB”
“基板传送错误 :|因发现检查气缸干涉基板, |气缸不能上升。| 请取下基板。”
[Cause]
Failed to lift up the cylinder that had been coming down since a PWB was detected at the cylinder
lifting-up position.
打算要使检查汽缸上升, 但是，因为在汽缸上升动作位置上检测出基板，所以没能进行上
升动作。
[Treatment]
Please take the PWB off the conveyor.
请除去传送轨道上的基板。
E650010 “Conveying device error: | Due to the abnormality of the check cylinder sensor, | cylinder can not
come up. | Please re-start the machine and check again”
“基板传送错误: |因检测到基板气缸传感器错误，气缸不能上升。重新启动后，再检查。”
[Cause]
The sensor of the check cylinder did not get ON within a certain time although you tried to run the
check cylinder.
虽进行检查气缸操作， 但检查气缸传感器不能在规定时间内开启。
[Treatment]
Select [Manual Control] from the menu bar, and choose [Control(C)] [Conveyor(C)] and [Movable
station control(A)]. Select “PWB detect pin” from the “Control Item” and [PWB detect pin(A)] from
[Control item] frame to enable or disable ON/OFF. The treatments to take depends on the result you
get from the action above.
1 Cylinder works fine.
1.1 The status of 'PWB check sensor' in the 'status' displaying frame gets ON/OFF.
The cause might be that the speed controller of the PWB detector was wrung too much. Please release
the speed controller of the PWB detector.
1.2 The status of 'PWB check sensor' in the 'status' displaying frame does not get ON/OFF.
1) The cause might be that PWB check sensor was adjusted to out of the operation range of the
cylinder. Please re-adjust the sensor to where it gets ON/OFF.
2) If the treatment1 above does not work, there is a possibility that the PWB check sensor is broken.
It could be that the wiring came out of the connector part, that a contact pin of the connector part is
broken, that wiring got cut off, or that sensor itself is broken (If LED of the PWB check sensor gets
ON/OFF but the status of 'PWB check sensor' in the 'status' displaying frame does not get ON/OFF,
signal line of the PWB check sensor may be either abnormal or cut off, or the connector part does not
work well).
Please examine the wiring and connector part. If any of them are broken, you need to replace them
with new ones.
3) If the treatment2 does not even work, PCB is broken or the wiring between the PCBs is bad.
2 Cylinder does not work.