JUKI贴片机错误代码.pdf - 第46页
E249001 “ The origin point ret urn is non-completion. Pl ease operate again after completing the origi n point return ” “ 没有执行返回原点。 | 请执行返回原点 后，再次操作。 ” [Cause] The axis has not yet b een returned to home. [Treatment] Ple…
I242555 “Please set online for MTS.”
“请连接 MTS。”
I242556 “Please close the door of MTS.”
“请关闭 MTS 的门。”
I242557 “Please insert the stacker of MTS.”
“请装入 MTS 的托盘存储箱。”
I242558 “Please attach the component to the nozzle manually.”
“请手动给吸嘴安装组件。”
I242559 “The pickup of components succeeded. The measurement begins.”
“组件被成功吸着，开始测定。”
Q242560 “Failed in picking components. Do you want to make a retry?”
“组件吸着失败，是否重试？”
I242561 “Please install components by the hand in the chuck. When the button is pressed, the chuck is
close.”
“请把组件用手动安装在夹盘内。单击按钮，就关闭夹盘。”
Q242562 “Please press 'Yes' if the installation of components is a success. Please press 'No' when doing
again.”
“已成功安装组件，请单击[是]﹔重试，请单击[否]。”
Q242563 “Please press 'Yes' if detach components by the hand. Please press 'No' when scrap components.”
“手动取下组件，请单击[是]﹔废弃组件，请单击[否]。”
Q242564 “Are components returned ?”
“是否归还组件？”
Q242565 “The components pickuped on the head are returned.”
“归还 Head 上的组件。”
Q242567 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.20 times as much as specified at the maximum.”
“现在的参数存在不稳定的因素。是否继续取得参数？ |最多进行设置次数 x 20 回左右的
测量动作。”
Q242568 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.10 times as much as specified at the maximum.”
“当前照明条件下，发生识别错误，是否继续取得动作？|最多测量动作次数是设置次数
x10。”
E249001 “The origin point return is non-completion. Please operate again after completing the origin point
return”
“没有执行返回原点。|请执行返回原点后，再次操作。”
[Cause]
The axis has not yet been returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E249002 “The OCC device is unused. The bank mark recognition is aborted”
“没有使用 OCC 设备。| 停止识别台架标记。”
[Cause]
OCC or OCC2 was set not to “Use” in the Use unit in Setup when performing the Bank mark
recognition.
[Treatment]
Please set OCC or OCC2 to “Use” in the Use unit in Setup.
E249003 “The stop key was pressed. The bank mark recognition is aborted”
“停止按钮被按下。| 停止识别台架标记。”
[Cause]
The stop key was pressed while the Bank mark recognition was in operation.
[Treatment]
“OK” button will completely abort the Bank mark recognition process.
E249004”The axis cannot be moved to recognition position. The bank mark recognition is aborted”
“轴不能移到识别位置。| 停止识别台架标记。”
[Cause]
An error occurred in the axis traveling.
[Treatment]
E249005 “The bank mark recognition error. The bank mark recognition is aborted”
“识别台架标记出错。| 停止识别台架标记。”
[Cause]
An error occurred in the Mark recognition by OCC unit.
[Treatment]
Please check and see if feeder bank is dirty or if something is concealing the feeder bank.
If the mark does not fit in the frame, you need to adjust the mark.
E249006 “MTS power off”
“MTS 电源被关闭。”
[Cause]
The power supply of MTS is off.
[Treatment]
Please turn on the power supply of MTS.
E249008 “The door of MTS opens”
“MTS 门已打开”
[Cause]
Failed to draw the MTS tray out since the MTS door was open.
[Treatment]
Please close the MTS door.
E249009 ”MTS offline”
“MTS 处于脱机状态”
[Cause]
MTS is not online.
[Treatment]
Please make MTS online.
E249010 “Servo is in the free state. The bank mark recognition is aborted”
[Cause]
The axis could not move since the servo was not locked.
[Treatment]
Please lock the servo using S-FREE switch.
Q249051 “Feeder bank has descended. Do you want to lift the feeder bank up and continue the bank mark
recognition?”
“送料器台架被下降。| 是否升高台架后，继续识别台架标记？”
[Cause]
The feeder bank had been descended when you tried to perform the Bank mark recognition.
[Treatment]
“YES” button will continue the Bank mark recognition process.
“NO” button will completely abort the Bank mark recognition process.
I249070 “Set online for MTS”
“设置的 MTS 没有联线”
[Cause]
Failed to draw the MTS tray out since the MTS was not online.
[Treatment]
Please make MTS online.
I249071 “Please close the door of MTS”
“请关闭 MTS 门”