JUKI贴片机错误代码.pdf - 第57页
E291029 “ MTC is not power on .” “ MTC 电源未打开。 ” E291030 “ MTC is not online .” “ 没有连 接 MTC 。 ” E291031 “ MTC initialize not done .” “ MTC 未初始化。 ” E291032 “ MTC is in the supply state .” “ MTC 处于补充状态。 ” E291033 “ MTC conv…
This process could not be executed since there is no complete placement data.
[Treatment]
Please input and complete the placement data.
E291022 “Because the one PWB is not clamped, cannot execute the BOC alignment”
“因为在上面没有固定基板，所以不能运行 BOC 校准。”
[Cause]
Any PWBs are clamped on the conveyor buffer. If there is no PWB, BOC mark recognition is not
available.
[Treatment]
Please load PWB(s) to BOC align.
E291023 “The automatic conveyor width adjustment is set in unused by the setup”
“在设置中，自动调整基板宽度没有被选用。”
[Cause]
Auto. PWB Width Alignment Control is set to “not use” in Setup.
[Treatment]
If Auto. PWB Width Alignment Control is available, please set it to “use” in the Setup. If not, this
operation cannot be executed.
E291024 “The BOC mark data send error [ID : &d]”
“BOC 标记信息发送失败 [ ID : %d ]”
[Cause]
BOC Mark data could not be sent to VCS.
[Treatment]
Please re-teach the Mark data to the machine.
E291025 “Servo off, it is not possible to operation”
“因伺服被关闭, 不能运行。”
[Cause]
Servo is in the free state.
[Treatment]
Please perform the Home returning.
E291026 “The PWB detected on conveyor. Please remove the PWB.”
“请取下传送轨道上基板。”
E291027 “Can't execute the BOC alignment,because PWB clamp is non-completion.”
“因为固定基板操作未结束，所以不能运行 BOC 校准。”
E291028 “Device selection is mistake.”
“设备选择有错误。”
E291029 “MTC is not power on.”
“MTC 电源未打开。”
E291030 “MTC is not online.”
“没有连接 MTC。”
E291031 “MTC initialize not done.”
“MTC 未初始化。”
E291032 “MTC is in the supply state.”
“MTC 处于补充状态。”
E291033 “MTC conveyor initialize not done.”
“MTC 传送没有进行初始化。”
E291034 “MTC Emergency Switch is Pressed.”
“MTC 处于紧急停止状态。”
E291035 “The PWB data is not set.”
“未输入基板数据。”
E291036 “The Coplanarity is set in unused by the setup. “
“在设置中，共面检测器没有被选用。”
E291037 “The BAD mark data is not set.| Operation is aborted.”
“未设置坏板标记数据。|停止执行。 “
E291038 “The BAD mark sensor is set in unused by the setup. “
“在设置中，坏板标记传感器没有被选用。 “
Q291500 “The BOC mark recognition error. | Please push 'No' when discontinuing. 'Yes' when continuing”
“识别 BOC 标记失败。|继续，请按[是]﹔停止，请按[否]。”
[Cause]
The BOC mark(s) could not be recognized by VCS.
[Treatment]
There is a possibility that the BOC mark(s) could not be taught to the machine properly.
Q291501 “Operation interruption. | Please push 'No' when discontinuing. 'Yes' when continuing”
“被用户中断。|继续，请按[是]﹔停止，请按[否]。”
[Cause]
The operation was aborted since STOP button was pressed.
[Treatment]
If you want continue the operation, press 'Yes'. If not, press 'No'.
Q291502 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291503 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291504 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291505 “Unit is moved to escape point. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“轴往等待位置移动，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291506 “Conveyor width is moved. Please remove handknob and PWB from conveyor. | Please push 'No'
when discontinuing. 'Yes' when continuing”
“移动基板幅宽，请取下基板和摇把。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check by removing PWBs and a handknob from the conveyor
since the conveyor width is adjusted.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.