JUKI贴片机错误代码.pdf - 第380页
issued. The process was aborted since th e mast er lock bit, block lock b it, and RP# lock were detected. ‧Flush memory is broken. [Treatment] ‧Please turn off the power supply and re-boot your machine. ‧If the error occ…
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691003 “Deleting cue of flush memory does not get useable”
“不能使用闪存卡的删除指令。”
[Cause]
'Deleting' cue did not get useable when checking its status after a 'deleting' command to flush memory
was issued.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691004 “WSM(Write State Machine) of flush memory does not get ready”
“闪存卡的WSM(Write State Machine)不能达到就绪状态。”
[Cause]
'WSM' did not get ready when checking its status after a command to flush memory was issued.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691005 “Write-in voltage range error occurred in flush memory control”
“闪存卡控制中发生写入电压范围错误。”
[Cause]
An error occurred while checking the 'Write-in' voltage status after a command to flush memory was
issued.
The process was aborted since the 'write-in' voltage is too low.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691006 “Write-in error occurred in flush memory control”
“闪存卡控制中发生设备保护错误。”
[Cause]
An error occurred while checking the 'device protecting' status after a command to flush memory was
issued.
The process was aborted since the master lock bit, block lock bit, and RP# lock were detected.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691007 “Write-in error occurred in flush memory control”
“闪存卡控制中发生写入错误。”
[Cause]
An error occurred while checking the 'Write-in' status after a command to flush memory was issued.
An error occurred while writing data in.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691008 “Command sequence error occurred in flush memory control”
“闪存卡控制中发生指令次序错误。”
[Cause]
An error occurred while checking the status after a command to flush memory was issued.
A command sequence error occurred.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691009 “Lock Bit Set error occurred n flush memory control”
“闪存卡控制中发生Lock Bit Set错误。”
[Cause]
An error occurred while checking the 'lock bit set' status after a command to flush memory was
issued.
An error occurred while setting the master/block lock bit.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691010 “Lock Bit Clear error occurred in flush memory control”
“闪存卡控制中发生Lock Bit Clear错误。”
[Cause]
An error occurred while checking the 'lock bit clear' status after a command to flush memory was
issued.
An error occurred while clearing the lock bit.
‧Flush memory is broken.
[Treatment]
‧Please turn off the power supply and re-boot your machine.
‧If the error occurs even after the re-boot, there is a possibility that the Safety board is broken.
Please contact our technical service dept. for information.
E691011 “The check word for the common data of flush memory is abnormal”
“闪存卡的共通数据的字节校验法(Check Word)错误。”
[Cause]
The type of the common data that is saved in the flush memory is irregular.
‧The common data is not saved in the flush memory.
‧Flush memory is broken.
[Treatment]
‧Please re-start the application.
‧Please re-install or version up the application.
‧If the error occurs even after the treatments above were performed, please contact our technical
service dept. for information.
E691012 “The checksum for the common data of flush memory is abnormal”
“闪存卡的共通数据的和数校验法(Check sum)错误。”
[Cause]
The common data that is saved in the flush memory is irregular.
‧The common data of flush memory is broken.
‧Flush memory is broken.
[Treatment]
‧Please re-start the application.
‧Please re-install or version up the application.
‧If the error occurs even after the treatments above were performed, please contact our technical
service dept. for information.
E691013 “The data version for the common data of flush memory is abnormal”
“闪存卡的共通数据的数据版本错误。”