JUKI贴片机错误代码.pdf - 第80页
[Cause] An error occurred during the m easurement(SWEEP) by laser. 1): Error code 2): A communication error occurred. 3): An axis error occurred Other : Please reference [Status list] in [Laser Control] in Ma nual Contro…
“不存在装配喷嘴的 ATC。|请用机械配置，给 ATC 安装喷嘴。”
[Cause]
Although Nozzle change was chosen in ATC control, no nozzle has been assigned to the ATC.
[Treatment]
Please allocate nozzles to ATC in ATC Nozzle allocation in Machine Setup.
W316042 “Nozzle is not set on head”
“Head 上没有装配喷嘴。”
[Cause]
Although Nozzle returning was chosen in ATC control, no nozzle has been installed on the specified
head.
[Treatment]
Please install a nozzle on the head, then try again.
E316051 “Z axis limit has been exceeded”
“Z 方向坐标超过界限。”
[Cause]
Z axis coordinate exceeded its limit. The axis can not move any further.
[Treatment]
Please move the axis within the limitation.
E316101 “Error has occurred when setting laser parameters |code: %ld”
“激光参数设置发生错误。|代码: %ld”
[Cause]
An abnormal matter happened when setting the Laser parameter.
1): Error code.
2): A communication error occurred.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316102 “Error has occurred during laser measurement(ONCE) | code: %ld”
An error occurred during the measurement(ONCE) by laser. “激光测量(ONCE)发生错误。|代码:
%ld”
1): Error code.
2): A communication error.
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316103 “Error has occurred during laser measurement(SWEEP) | code:%ld”
“激光测量(SWEEP)发生错误。|代码: %ld”
[Cause]
An error occurred during the measurement(SWEEP) by laser.
1): Error code
2): A communication error occurred.
3): An axis error occurred
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316104 “Error has occurred during the nozzle presence check | code:%ld”
“检查喷嘴是否存在时，发生错误。|代码: %ld”
[Cause]
An error occurred during the measurement(ONCE) by laser.
1): Error code.
2): A communication error.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316105 “Error has occurred during the image data obtain. | code:%ld”
“获取图像数据发生错误。|代码: %ld”
[Cause]
An error occurred while getting the Image data by laser.
1): Error code
2): A communication error occurred.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316106 “Error has occurred during the edge check data learning. | code:%ld”
“获取确定边界数据发生错误。|代码: %ld”
[Cause]
An error occurred while getting the Edge check by laser.
1): Error code.
2): A communication error occurred.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316107 “Data has not been learned”
“不能获取数据。”
[Cause]
Z axis coordinate by HMS could not be learned since it was out of the measurement range (-40mm
through +40mm)
[Treatment]
Please check and see if the measuring position (XY coordinates) of HMS is correct or not.
E316301 “MTC power off”
“MTC 电源被关闭。”
[Cause]
The power supply of MTC is off.
[Treatment]
Please turn on the power supply of MTC, and make it online.
E316302 “MTC offline”
“MTC 处于脱机状态。”
[Cause]
MTC is not online
[Treatment]
Please make MTS online.
E316303 “MTC is in the supply state”
“MTC 处于补充状态。”
[Cause]
MTC can not be controlled since it is in the Supply (component change) state.
[Treatment]
Please make MTC a normal status.
E316401 “MTS power off”
“MTS 电源被关闭。”
[Cause]
Failed to draw the MTS tray out since the MTS was not ON.
[Treatment]
Please turn on the power supply of MTS.
E316402 “MTS offline”
“MTS 处于脱机状态。”
[Cause]
Failed to draw the MTS tray out since the MTS was not online.
[Treatment]
Please make MTS online.