JUKI贴片机错误代码.pdf - 第63页
E301011 “ An error occurred wh ile installing nozzles .” “ 安装吸 嘴发生错误。 ” E301012 “ An error occurred while measur ing nozzle height by Laser ” “ 激光测定吸嘴高度发生错误。 ” [Cause] An error occurred during the lase r hei ght measurem…
[机器设置、手动控制、各 I/O 安全方向设置]
E301000 “Memory allocation error”
“分配内存错误”
[Cause]
The working space can not be saved.
内存不足。
[Treatment]
Please add some more memory available to save the working space.
请增加可用内存。
E301001 “There is no input character”
“没有输入字符。”
[Cause]
There was no character when you hit Enter key to define characters.
没有输入字符。
[Treatment]
Please enter characters.
请输入字符。
E301002 “Input character has irregularities”
“输入非法字符。”
[Cause]
The letter strings had irregularities when defining the input.
存在非法字符。
[Treatment]
Please enter proper characters.
请正确输入字符。
E301003 “Input value exceeds predetermined data range. | (Data range: %s)”
“输入值超过输入范围。|(输入范围:%s)”
[Cause]
The value when defining the input exceeded the input range.
输入值超过输入范围。
[Treatment]
Please enter the values that are within the range.
请输入允许范围内的值。
E301004 “Window create error(%s)”
“建立窗口错误(%s)”
E301011 “An error occurred while installing nozzles.”
“安装吸嘴发生错误。”
E301012 “An error occurred while measuring nozzle height by Laser”
“激光测定吸嘴高度发生错误。”
[Cause]
An error occurred during the laser height measurement by laser.
[Treatment]
Something might be wrong with Laser alignment. Please check it.
E301014 “Failure has occurred during measurement of nozzle shape by laser. | Laser status: %3d”
“激光测定吸嘴外形发生错误。| 激光状态: %3d”
E301015 “Specify user's individual nozzle No.”
“%s | 设置用户个别吸嘴号。”
[Cause]
When measuring the width of a nozzle's outer shape by laser, the output does not coincide with that of
a standard nozzle. Therefore, the nozzle number can not be set automatically. As a temporary nozzle
No., the smallest nozzle number (530) of option nozzles is set for the nozzle.
[Treatment]
If the nozzle is a standard nozzle, please measure it again. If the same result comes out, something
might be wrong with the nozzle shape. Please check the nozzle. If the nozzle is an option nozzle, the
nozzle number set is just a temporary number and might be wrong. Please set a nozzle number for the
nozzle again. If you measure the nozzle again after set a nozzle number for the nozzle, the temporary
nozzle number will be set again.
E301016 “An error occurred while taking nozzles off”
“因卸下吸嘴，发生错误。”
[Cause]
This message occurs when the machine determines that the nozzle is still on the head even despite the
nozzle removal took place.
[Treatment]
If the nozzle is not on the head, the laser might be too dirty to work properly. Please clean the laser.
Also, please check and see if the slide plate can slide properly or the sensor works properly with
Manual control. If the slide plate or the sensor does not work well, something might be broken. Please
take a note of the error No. and contact our technical service dept. for information.
E301017 “Selected device can not move to this position. | Please reselect other device on HOD”
“被选设备不能移到目标位置。|请重新选择其它设备。”
[Cause]
You cannot go into the teaching mode since you can not move to the specified position with the
device selected by HOD.
[Treatment]
Please reselect a device available.
E301018 “Selected device is not installed. | Please reselect other device on HOD”
“被选设备尚未安装。|请重新选择其它设备。”
[Cause]
Since the device selected by HOD has not been installed (the installation of the device is not set in the
option of MS parameter), you can go into the teaching mode.
[Treatment]
Please reselected a device available.
E301019 “Return to home has not yet been completed”
“尚未完成原点返回。”
[Cause]
The axis has not yet returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E301020 “MTC power off”
“没有打开 MTC 电源。”
[Cause]
Failed to draw MTC shuttle out when teaching MTC shuttle pick position to the machine since MTS
was not ON.
[Treatment]
Please turn on the power supply of MTC.
E301021 “MTC offline”
“MTC 处于脱机状态。”
[Cause]
Failed to draw the MTC shuttle out when teaching MTC shuttle pick position to the machine since
MTC was not online.
[Treatment]
Please make MTC online.
E301022 “File I/O Error|Error code:%02d|File name:%s”
“文件 I/O 错误|错误代码:%02d|文件名:%s”
E301023”There is no installed head”
“不存在可用 Head。”
[Cause]