JUKI贴片机错误代码.pdf - 第79页
“ 不存在装配喷嘴的 AT C 。 | 请用机械配置，给 ATC 安装喷嘴。 ” [Cause] Although Nozzle change was chosen i n ATC control, no nozzle has been assigned to the ATC. [Treatment] Please alloca te nozzles to ATC in ATC Nozzle allocation in Mach ine…
There was no character when you hit Enter key to define characters.
[Treatment]
Please enter characters.
E316012 “Input character has irregularities”
“输入了非法字符。”
[Cause]
The letter strings had irregularities when defining the input.
[Treatment]
Please enter proper characters.
E316013 “Input value exceeds predetermined data range”
“输入值超过范围。”
[Cause]
The value when defining the input exceeded the input range.
[Treatment]
Please enter the values that are within the range.
E316021 “Return to home has not yet been completed”
“尚未结束原点返回。”
[Cause]
The axis has not yet been returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E316022 “Servo is in the free state”
“伺服处于不使用状态。”
[Cause]
The axis could not move since the servo is not locked.
[Treatment]
Please lock the servo with S-FREE switch.
E316031 “Selected device is not install. Please reselect other device on HOD”
“被选设备尚未安装。|请重新选择其它设备。”
[Cause]
You could not go into the teaching mode since the device selected by HOD has not been installed.
[Treatment]
Please reselect the device which is currently installed.
W316041 “There is no ATC that is allocated with nozzle. Allocate nozzle to ATC when setting up the
machine”
“不存在装配喷嘴的 ATC。|请用机械配置，给 ATC 安装喷嘴。”
[Cause]
Although Nozzle change was chosen in ATC control, no nozzle has been assigned to the ATC.
[Treatment]
Please allocate nozzles to ATC in ATC Nozzle allocation in Machine Setup.
W316042 “Nozzle is not set on head”
“Head 上没有装配喷嘴。”
[Cause]
Although Nozzle returning was chosen in ATC control, no nozzle has been installed on the specified
head.
[Treatment]
Please install a nozzle on the head, then try again.
E316051 “Z axis limit has been exceeded”
“Z 方向坐标超过界限。”
[Cause]
Z axis coordinate exceeded its limit. The axis can not move any further.
[Treatment]
Please move the axis within the limitation.
E316101 “Error has occurred when setting laser parameters |code: %ld”
“激光参数设置发生错误。|代码: %ld”
[Cause]
An abnormal matter happened when setting the Laser parameter.
1): Error code.
2): A communication error occurred.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316102 “Error has occurred during laser measurement(ONCE) | code: %ld”
An error occurred during the measurement(ONCE) by laser. “激光测量(ONCE)发生错误。|代码:
%ld”
1): Error code.
2): A communication error.
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316103 “Error has occurred during laser measurement(SWEEP) | code:%ld”
“激光测量(SWEEP)发生错误。|代码: %ld”
[Cause]
An error occurred during the measurement(SWEEP) by laser.
1): Error code
2): A communication error occurred.
3): An axis error occurred
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316104 “Error has occurred during the nozzle presence check | code:%ld”
“检查喷嘴是否存在时，发生错误。|代码: %ld”
[Cause]
An error occurred during the measurement(ONCE) by laser.
1): Error code.
2): A communication error.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316105 “Error has occurred during the image data obtain. | code:%ld”
“获取图像数据发生错误。|代码: %ld”
[Cause]
An error occurred while getting the Image data by laser.
1): Error code
2): A communication error occurred.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316106 “Error has occurred during the edge check data learning. | code:%ld”
“获取确定边界数据发生错误。|代码: %ld”
[Cause]
An error occurred while getting the Edge check by laser.
1): Error code.
2): A communication error occurred.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment]
Please reference [Status list] in [Laser Control] in Manual Control.
E316107 “Data has not been learned”
“不能获取数据。”