JUKI贴片机错误代码.pdf - 第185页
E604341 “ Axi s Driver:| T3-axis. The dac out error exceeded the limit .” “ T3 轴错误 |DAC 输出超 出界限。 ” E604441 “ Axi s Driver:| T4-axis. The dac out error exceeded the limit .” “ T4 轴错误 |DAC 输出超 出界限。 ” E604541 “ Axi s Driver…
E604438 “Axis Driver:| T4-axis The position error exceeded the limit.”
“ T4 轴错误: 位置偏移量超过界限。”
E604538 “Axis Driver:| RT1-axis The position error exceeded the limit.”
“RT1 轴错误: 位置偏移量超过界限。”
E604638 “Axis Driver:| RT2-axis The position error exceeded the limit.”
“RT2 轴错误: 位置偏移量超过界限。”
E604738 “Axis Driver:| RT3-axis The position error exceeded the limit.”
“RT3 轴错误: 位置偏移量超过界限。”
E604838 “Axis Driver:| RT4-axis The position error exceeded the limit.”
“RT4 轴错误: 位置偏移量超过界限。”
E604139 “Axis Driver:| T1-axis Amp fault error.”
“ T1 轴错误: Amp 故障。”
E604239 “Axis Driver:| T2-axis Amp fault error.”
“ T2 轴错误: Amp 故障。”
E604339 “Axis Driver:| T3-axis Amp fault error.”
“ T3 轴错误: Amp 故障。”
E604439 “Axis Driver:| T4-axis Amp fault error.”
“ T4 轴错误: Amp 故障。”
E604539 “Axis Driver:| RT1-axis Amp fault error.”
“RT1 轴错误: Amp 故障。”
E604639 “Axis Driver:| RT2-axis Amp fault error.”
“RT2 轴错误: Amp 故障。”
E604739 “Axis Driver:| RT3-axis Amp fault error.”
“RT3 轴错误: Amp 故障。”
E604839 “Axis Driver:| RT4-axis Amp fault error.”
“RT4 轴错误: Amp 故障。”
E604141 “Axis Driver:| T1-axis. The dac out error exceeded the limit.”
“ T1 轴错误 |DAC 输出超出界限。”
E604241 “Axis Driver:| T2-axis. The dac out error exceeded the limit.”
“ T2 轴错误 |DAC 输出超出界限。”
E604341 “Axis Driver:| T3-axis. The dac out error exceeded the limit.”
“ T3 轴错误 |DAC 输出超出界限。”
E604441 “Axis Driver:| T4-axis. The dac out error exceeded the limit.”
“ T4 轴错误 |DAC 输出超出界限。”
E604541 “Axis Driver:| RT1-axis. The dac out error exceeded the limit.”
“RT1 轴错误 |DAC 输出超出界限。”
E604641 “Axis Driver:| RT2-axis. The dac out error exceeded the limit.”
“RT2 轴错误 |DAC 输出超出界限。”
E604741 “Axis Driver:| RT3-axis. The dac out error exceeded the limit.”
“RT3 轴错误 |DAC 输出超出界限。”
E604841 “Axis Driver:| RT4-axis. The dac out error exceeded the limit.”
“RT4 轴错误 |DAC 输出超出界限。”
E605110 “Axis Driver:| Support table parameter error.”
“支撑台参数错误。”
E605210 “Axis Driver:| Right Support table parameter error.”
“右支撑台参数错误。”
E605310 “Axis Driver:| AWC parameter error.”
“自动调整基板宽度(AWC)参数错误。”
E605510 “Axis Driver:| Center motor parameter error.”
“中心马达参数错误。”
E605610 “Axis Driver:| Right Center motor parameter error.”
“右中心马达参数错误。”
E605111 “Axis Driver:| Station is not used.”
“没有选用左侧站点。”
E605211 “Axis Driver:| Station is not used.”
“没有选用右侧站点。”
E605112 “Axis Driver:| Support table failed originating.”
“支撑台的返回原点失败。”
E605212 “Axis Driver:| Right Support table failed originating.”
“右支撑台的返回原点失败。”
E605312 “Axis Driver:| AWC failed originating.”
“自动调整基板宽度的返回原点失败。”
E605113 “Axis Driver:| Support table error.|Servo power is OFF.”
“支撑台的电源被关闭。”
E605213 “Axis Driver:| Right Support table error.|Servo power is OFF.”
“右支撑台的电源被关闭。”
E605313 “Axis Driver:| AWC error.|Servo power is OFF.”
“自动调整基板宽度的电源被关闭。”
E605513 “Axis Driver:| Center motor error.|Servo power is OFF.”
“中心马达的电源被关闭。”
E605613 “Axis Driver:| Right Center motor error.|Servo power is OFF.”
“右中心马达的电源被关闭。”
E605119 “Axis Driver:| Support table error.|Stopper is locked.”
“支撑台的制动器被锁定。”
E605219 “Axis Driver:| Right Support table error.|Stopper is locked.”
“右支撑台的制动器被锁定。”
E605130 “Axis Driver:| XMP error occurred on support table.”
“支撑台发生 XMP 错误。”
E605230 “Axis Driver:| XMP error occurred on right support table.”
“右支撑台发生 XMP 错误。”
E605330 “Axis Driver:| XMP error occurred on AWC.”
“自动调整基板宽度发生 XMP 错误。”
E605530 “Axis Driver:| XMP error occurred on center motor.”
“中心马达发生 XMP 错误。”
E605630 “Axis Driver:| XMP error occurred on right center motor.”
“右中心马达发生 XMP 错误。”
E605131 “Axis Driver:| Support table status error.”
“支撑台发生状态错误。”
E605231 “Axis Driver:| Right Support table status error.”
“右支撑台发生状态错误。”