JUKI贴片机错误代码.pdf - 第441页
[Cause] Indicates that the line has 710, 720, or 770. [Deal] Check the circuit division nu mber (n x n). E3868 No adhesize data exists,unless dispensing bond. [Cause] Appears if there is no adhesion data despite "Mo…
E3862 The designated station does not support directed inspection.
[Cause]
Appears if any other inspection defined in the following table is selected in an invalid combination
with a particular station.
(Specified station) (Chip standup) (Verify) (Coplanarity)710 OK
720 OK
730 OK OK
740 OK OK OK
750 OK OK
760 OK OK OK
2010 OK OK
2020 OK OK OK
2030 OK OK
2040 OK OK OK
[Deal]
For available inspection for a particular station, refer to the above table.
E3863 Designated station's IC marks are over 50.
[Cause]
Appears if more than 50 IC marks are specified for one station.
[Deal]
Specify another station, or decrease the allocated IC marks to 50 or less.
E3864 IC marks are over max value.
[Cause]
Excessive IC marks have been specified.
[Deal]
Decrease the specified IC marks to the maximum or less.
W3865 Position conflicts betweer feeder and IC collection belt.
[Explanation]
Appears if the installation position is different from the position specified for the absorption data,
with the IC recycle belt enabled during the MSL setup.
E3866 PWB size is over max value.
[Cause]
Excessive line configuration has been set during the MSL setup to the largest PWB size.
[Deal]
Find out the PWB size available for the line configuration set during the MSL setup.
E3867 Station which cannot support more than 100 circuits is in the line.
[Cause]
Indicates that the line has 710, 720, or 770.
[Deal]
Check the circuit division number (n x n).
E3868 No adhesize data exists,unless dispensing bond.
[Cause]
Appears if there is no adhesion data despite "Mounting-Application" or "Only Mounting" is selected
for the item "Application/Mounting" in the mounting data.
[Deal]
Create adhesion data.
E3908 “File open failed. “
"打开文件失败."
E3909 “File close failed. “
"关闭文件失败."
E3910 “Data read-in or file conversion failed. “
"数据读入或文件转换失败."
E3914 “File has no extension. “
"文件不扩展."
E3919 “INI file has no entry. “
"INI 文件没有目录."
E3920 “Memory cannot be secured. Please terminate other application and do it again. “
"内存不能被保护，请终止其它应用并重新执行."
E3928 “File is being used by another application. Please terminate other application and do it again. “
"文件已经被其它应用使用，请终止其它应用并重新操作."
E3929 “This file type is not supported. File version or file type is incorrect. Please check the file. “
"不支持该文件类型. 文件版本或文件类型不正确.请检查文件."
E4001 “Initialization failed. “
"初始化失败."
E4002 “Allocation for profile use failed. “
"为剖面使用分配失败."
E4003 “Allocation for line configuration use failed. “
"给线外形分配使用失败."
E4004 “Allocation for source table use failed. “
"为资源表使用分配失败."
E4005 “Allocation for use of previously mounted components failed. “
"为预定贴装使用分配失败."
E4006 “Line configuration file is incorrect.Please repeat setup. “
"线结构文件不正确，请重新设置."
E4007 “INI file information is incorrect.Please repeat setup. “
"文件信息不正确，请重新设置."
E4008 “Reserved program does not exist. “
"保留程序不存在."
E4009 “Reserved program file cannot be created. “
"不能创建保留程序文件."
E4010 “Opening of reserved program file failed. “
"打开保留程序失败."
E4011 “Read-in of reserved program file failed. “
"读入保留程序失败."
E4012 “Write-in of reserved program file failed. “
"写入保留程序失败."
E4013 “Reserved program for production not yet performed does not exist. “
"不能执行的为生产的保留程序不存在."
E4014 “Full management information line cannot be set. “
"
整体管理信息线不能被设置."
E4015 “Acquisition of information for full management information line failed. “
"为整体管理信息获得信息失败."
E4016 “Management information station ID = %dinformation acquisition failed. “
"管理信息位置 ID=%D 获得信息失败."
E4017 “Number of components information station ID = %dinformation acquisition failed. “
"获得组件信息位置 ID=％d 信息数量失败."
E4018 “Number of components information area allocation failed. “
"组件信息区域数量分配失败."