JUKI贴片机错误代码.pdf - 第72页
E301077 “ IP address 0.0.0.0 is invalid .” “ 0.0.0.0 是不正确的 IP 地址。 “ E301078 “ The IP address contains blanks .” “ IP 地址上 有空格。 “ Q302000 “ Reset I/O? ” “ 是否进行各 I/O 的安全方向设定？ ” [Cause] You are asked if to set each I /O in t…
E301062 “There is no head that can move to specified position.”
“不存在可以移到指定位置的吸嘴。”
W301063 “Selected MTC/MTS is not connected.”
“已被选用的 MTC/MTS 处于脱机状态。”
E301064 “MTS is in the supply state.”
“MTS 处于补充状态。”
E301065 “%s ||Specified nozzle data has not been registered.|Please register nozzle data.”
“%s ||吸嘴信息没有注册。|请注册吸嘴信息。”
E301066 “The nozzle no. is invalid.”
“无效的吸嘴号。”
E301067 “A drive can not be access.|Please check the FD”
“不能访问 A 驱动器。|请确认一下软盘。”
E301068 “Because the right head is disable, it can not be measured.”
“因为右 Head 处于不使用状态，所以不能进行测量。”
E301069 “Input value exceeds predetermined data range.”
“输入数据超过范围。”
E301070 “It can not be set the small nozzle on a large ATC.”
“大型 ATC 上不能安装小型吸嘴。”
E301071 “The SemiAuto Trash box is not at the abandonment position.|Please set the SemiAuto Trash box at
the abandonment position.”
“半自动废弃盒不在废弃位置。|请把半自动废弃盒设置在废弃位置。”
E301072 “The production program has not read.”
“不能读取生产程序。”
E301073 “An error occurred while BOC alignment.”
“BOC 校准发生错误。”
E301074 “An error occurred while BOC Mark Correct.”
“BOC 标记校正发生错误。”
W301075 “Because the nozzle data[ %s ] is initial data, it can not be delete.”
“因为被选吸嘴的信息[ %s ]是初始数据，不能删除。”
W301076 “Input value exceeds the simultaneous BOC mark recognition limit.|Please check out the Y value.”
“输入值超过了同时识别 BOC 标记的范围。|请检查一下 Y 坐标值。”
E301077 “IP address 0.0.0.0 is invalid.”
“ 0.0.0.0 是不正确的 IP 地址。 “
E301078 “The IP address contains blanks.”
“ IP 地址上有空格。 “
Q302000 “Reset I/O?”
“是否进行各 I/O 的安全方向设定？”
[Cause]
You are asked if to set each I/O in the safety direction.
[Treatment]
“YES” button will sets I/O in the safety direction.
“NO” button will discontinue to exit the Manual control.
Q302001”Exit machine setup. | Set value is saved?”
“退出机器设置。|是否保存设置？”
[Cause]
You are asked if to save the parameter that was set in Machine Setup.
[Treatment]
“YES” button will save the set value.
“NO” button will not save the set value.
“Cancel” button will cancel your inquiry.
Q302002 “Error has occurred during automatic measurement of nozzle. | Do you interrupt automatic
measurement?”
“吸嘴的自动测量发生错误。|是否停止自动测量？”
[Cause]
An error occurred during the auto. nozzle measurement of ATC nozzle allocation. You are asked if to
abort the following ATC auto. measurement.
[Treatment]
“YES” button will abort the auto. measurement.
“NO” button will continue the auto. measurement.
Q302003 ”Return to home has not yet been completed. | Return to home?”
“未完成原点返回。|是否进行原点返回？”
[Cause]
The axis has not returned to home yet. You are asked if to perform Home returning.
[Treatment]
“YES” button will perform the Home returning, and continue the process.
“NO” button will not perform the Home returning, but continue the process.
Q302004 ”Error has occurred during nozzle installation. | Move to parking position?”
“安装吸嘴发生错误。|是否移到待命位置？”
[Cause]
A nozzle installation error of ATC nozzle allocation occurred. You are asked if to move the head to
the nozzle removal position.
[Treatment]
“YES” button will move the head to the nozzle removal position, and continue the process.
“NO” button will not move the head to the nozzle removal position, but continue the process.
Q302005 “Extend shuttle?”
“是否取出滑梭？”
[Cause]
You are asked if to draw a shuttle out of MTC when teaching the MTC shuttle pick position to the
machine.
[Treatment]
“YES” button will draw the shuttle from MTC, and get in the teaching mode.
“NO” button will no draw the shuttle from MTC, but get in the teaching mode.
Q302006 “Do you interrupt automatic measurement?”
“是否停止自动测量？”
[Cause]
STOP switch was pressed while nozzle were automatically assigned. You are asked if to abort the
auto. measurement.
[Treatment]
“YES” button will abort the auto. measurement.
“NO” button will continue the auto. measurement.
Q302007 “A nozzle is fixed to %s. | Do you want to auto-return the nozzle?”
“吸嘴被装配在%s。 |是否自动放回吸嘴？”
[Cause]
With a nozzle on the head, the head in the Use unit was changed to “not use” from “use” You are
asked if to return the nozzle to ATC before enabling the change.
[Treatment]
“YES” button will return the nozzle installed on the head.
“NO” button will enable the change with the nozzle on the head. When you choose “NO”, you need
to cancel the nozzle allocation in the 'ATC nozzle allocation'.
Q302008 “Extend MTS mark?”
“是否获取 MTS 标记？”
[Cause]