00196044-05 - sg x und x4i fse_en.pdf - 第452页

Modular Conveyor Conveyor Settings Setting the Fixed Conveyor Side (from SW701) S tudent Guide (FSE) SI PL ACE X Series and X4I Modular Conveyor Edition 01/2009 EN 452 1 1.3.2 Setting the Fixed Conveyor Side (from SW701)…

100%1 / 632
Modular Conveyor
Setting the Belt Tension Conveyor Settings
Student Guide (FSE) SIPLACE X Series and X4I
Edition 01/2009 EN Modular Conveyor
451
Legend
11.3.1.1 Belt Tension of PCB Conveyor (SIPLACE X, X4I)
1 Width adjustment stepping motor 4 Toothed drive belt for adjusting the width /
measuring the belt tension
2 Toothed belt for the drive
3 Adjustment unit 1.2 and 3 T Transport direction
11-9: Width adjustment motor
The belt is tensioned is set by means of cams on
the idler pulleys. The idler pulleys are located on
the left and right of the motor.
Legend
1. Loosen the cam shaft on the idler pulley and
set the belt tension.
NOTE:
The modular conveyor uses different belt lengths. The different belt tensions between the
conveyor lanes are due to the different arrangement of hexagonal shafts and deflection pulleys.
Belt tension For lane 1
(single and dual conveyor)
For lane 2
(dual conveyor)
Belt tension for the width adjustment 30 Hz +/-2 Hz
Input belt 102 Hz +/- -10 Hz 144 Hz +/- -14 Hz
Placement area 1 66 Hz +/- -7 Hz 71 Hz +/- -7 Hz
Intermediate belt 94 Hz +/- -9 Hz 94 Hz +/- -9 Hz
Placement area 2 66 Hz +/- -7 Hz 71 Hz +/- -7 Hz
Output belt 102 Hz +/- -10 Hz 144 Hz +/- -14 Hz
Modular Conveyor
Conveyor Settings Setting the Fixed Conveyor Side (from SW701)
Student Guide (FSE) SIPLACE X Series and X4I
Modular Conveyor Edition 01/2009 EN
452
11.3.2 Setting the Fixed Conveyor Side (from SW701)
11.3.2.1 General Notes
Setting the fixed conveyor side
The fixed conveyor side is always set in the standard mode with right side fixed. You need to set a value
of 38.8 mm between the conveyor base and the fixed conveyor side, with the help of a gauge.
03054247-xx: Gauge for fixed conveyor side DT/ET HS60/D4
03054248-xx: Distance gauge for conveyor side DT HS-60/D4
Teach the fixed side with the software and store the value.
11-10: Setting the fixed conveyor side
Values
The measurement is performed between the side flange and the fitting flange of the mounting frame.
(See also "Example for X Series")
When using dual conveyors in the X4I, the fixed
conveyor side can be set as required i.e. the left or
right side, or the outer edges of each conveyor for
i-placement. The compatibility to the other
machines can be set via predefined values in the
SW (see diagram).
NOTE:
This menu is available from user level
Service (customer)
!
Machine Single conveyor
Standard width
508 (460) mm
Dual conveyor
Standard width
250 (216) mm
Quad lane
Standard width
114 mm
HF series 19 (43) mm 4.5 (38.8) mm
X series / D3
up to July 2007
19 (43) mm 4.5 (38.8) mm
X series / D3
from July 2007
16 (40) mm 4.5 (38.8) mm 2 mm
X4I 16 (40) mm 4.5 (38.8) mm 2 mm
Modular Conveyor
Setting the Fixed Conveyor Side (from SW701) Conveyor Settings
Student Guide (FSE) SIPLACE X Series and X4I
Edition 01/2009 EN Modular Conveyor
453
Example of X series
11-11: Setting the "fixed conveyor side" in SIPLACE X, HF series
Shaft fixtures (bearing flange)
Machine Single conveyor
Standard width
460 mm
Dual conveyor
Standard width
216 mm
HS-60 34.5 mm 30.5 mm
S27 HM 34.5 mm 30.5 mm
D4 34.5 mm 30.5 mm
D1/D2 34.5 mm 30.5 mm
NOTE:
The fixed conveyor side should be adjusted only with the SITEST software and the width
adjustment devices. This ensures that the conveyor sides are in their correct positions (parallel)
i.e. that the conveyor runs straight.
NOTE:
Since July 2007, X machines with single conveyors use a new version of the shaft fixtures
(bearing flange) with a width of 15 mm, instead of 12 mm. The setting for standard single
conveyors changes with this new version, to 40 mm.