YAMAHA 报警资料.pdf - 第102页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 102 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

Comparison Table ( English - Chinese )

Code

CodeCode

Code

English

EnglishEnglish

English

Chinese

ChineseChinese

Chinese

Ea03924 DISPENSE PROTECT

The data of dispense which is less than the appointed restriction

value exists. Check the quantity of dot(pre)dispense in board data,

and rate of nozzles in machine data.

Kind

1:Predispense 2:Dotdispense 3:Sequence

Dispense data No.

Quantity

Nozzle(Type)

Rate

Dispense Low Limit(ms)

涂胶量限制保

存在比指定的限制量低的涂胶量数据。

󲣌确󲡹基板程序中的正式(󳕙)点胶数据的涂胶量，

以及机器󲢓置画面中使用点胶嘴的系数数据。

󱥐

1:󳕙点胶 2:正式点胶 3:作流程

点胶数据 No.号

胶液量

使用 Nozzle(󱥐型)

系数

涂胶量限制(ms)

Ea03926 DATA CHECK ERROR

Wait Point(Y) exceeds Safety Pos.for Camera(Machine Y Axis).

Please set it to less than Wait Point(Y) minus Head Offset(Y).

Please correct the machine settings and read same Board data.

Wait Point(Y)

[Setting][Machine Data][Mechanical][Position]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

Head Offset(Head1-2 Y)

[Setting][Machine Data][Head][Head Offset]

数据󰖕󰒺󳇮󲣄

待机位置(Y)超出了相机安全位置(主机 Y 󲱉坐󰓜)。

󲣌在相机安全位置(主机 Y 󲱉坐󰓜) - Head 偏移量(Head Y)内󲢓置。

󲣌正确󲢓置[机器󲢓置]画面后，重新󲣐入基板程序。

待机位置(Y)

[机器󲢓置][机器数据][机械坐󰓜][位置坐󰓜]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Head 偏移量(Head 1-2 Y)

[机器󲢓置][机器数据][Head][Head 偏移量]

Ea03927 DATA CHECK ERROR

Discard Point(Y) exceeds Safety Pos.for Camera(Machine Y Axis).

Please set it to less than Discard Point(Y) minus Head Offset(Y).

Please correct the machine settings and read same Board data.

Discard Point(Y)

[Setting][Machine Data][Mechanical][Position]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

Head Offset(Head1-2 Y)

[Setting][Machine Data][Head][Head Offset]

数据󰖕󰒺󳇮󲣄

弃位置(Y)超出了相机安全位置(主机 Y 󲱉坐󰓜)。

󲣌在相机安全位置(主机 Y 󲱉坐󰓜) - Head 偏移量(Head Y)内󲢓置。

󲣌正确󲢓置[机器󲢓置]画面后，重新󲣐入基板程序。

弃位置(Y)

[机器󲢓置][机器数据][机械坐󰓜][位置坐󰓜]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Head 偏移量(Head 1-2 Y)

[机器󲢓置][机器数据][Head][Head 偏移量]

Ea03928 DATA CHECK ERROR

Dump Station(Y) exceeds Safety Pos.for Camera(Machine Y Axis).

Please set it to less than Dump Station(Y) minus Head Offset(Y).

Dump Station No.

Please correct the machine settings and read same Board data.

Dump Station(Y)

[Setting][Machine Data][Mechanical][Position]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

Head Offset(Head1-2 Y)

[Setting][Machine Data][Head][Head Offset]

数据󰖕󰒺󳇮󲣄

弃位置(Y)超出了相机安全位置(主机 Y 󲱉坐󰓜)。

󲣌在相机安全位置(主机 Y 󲱉坐󰓜) - Head 偏移量(Head Y)内󲢓置。

弃站号

󲣌正确󲢓置[机器󲢓置]画面后，重新󲣐入基板程序。

弃站(Y)

[机器󲢓置][机器数据][机械坐󰓜][位置坐󰓜]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Head 偏移量(Head 1-2 Y)

[机器󲢓置][机器数据][Head][Head 偏移量]

Ea03929 DATA CHECK ERROR

Dipping Area(Y) exceeds Safety Pos.for Camera(Machine Y Axis).

Please set it to less than Dipping Area(Y) minus Head Offset(Y).

Dipping Station No.

Please correct the machine settings and read same Board data.

Dipping Area1-2(Y):Station Origin + Station Size

[Setting][Machine Data][Station][Dipping Station]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

Head Offset(Head1-2 Y)

[Setting][Machine Data][Head][Head Offset]

数据󰖕󰒺󳇮󲣄

浸胶范(Y)超出了相机安全位置(主机 Y 󲱉坐󰓜)。

󲣌在相机安全位置(主机 Y 󲱉坐󰓜) - Head 偏移量(Head Y)内󲢓置。

浸胶站号

󲣌正确󲢓置[机器󲢓置]画面后，重新󲣐入基板程序。

浸胶范(Y): 浸胶站原点 + 浸胶站尺寸

[机器󲢓置][机器数据][站装置][浸胶站]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Head 偏移量(Head 1-2 Y)

[机器󲢓置][机器数据][Head][Head 偏移量]

Ea03930 DATA CHECK ERROR

Dispense Area on Dot Station(Y) exceeds Safety Pos.for Camera(Y).

Please set it to less than Dispense Area on Dot Station(Y)

minus Head Offset(Y).

Please correct the machine settings and read same Board data.

Dispense Area on Dot Station(Y):Station Datum(Y) + Size(Y)

[Setting][Machine Data][Station][Dot Station]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

Head Offset(Head1-2 Y)

[Setting][Machine Data][Head][Head Offset]

数据󰖕󰒺󳇮󲣄

打点站上的涂胶范(Y)超出了相机安全位置。

󲣌在相机安全位置(主机 Y 󲱉坐󰓜) - Head 偏移量(Head Y)内󲢓置。

󲣌正确󲢓置[机器󲢓置]画面后，重新󲣐入基板程序。

打点站上的涂胶范(Y): 打点站基准(Y) + 尺寸(Y)

[机器󲢓置][机器数据][站装置][打点站]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Head 偏移量(Head 1-2 Y)

[机器󲢓置][机器数据][Head][Head 偏移量]

Ea03931 A PARTS NUMBER IS ABNORMAL

The parts number registered with mount data is

abnormal. It occurs for the time when data after a

ASCII change is used just as it is. Please use the

board data of the line distribution and the

optimization execution ending.

Mount data

元件号󱓖异常

登在󲨉装数据上的元件号󱓖异常。

使用 ASCII 󲱁󰀷后的数据󰋋生。

󲣌使用已󱮤󲲰行󲲜生󱮔分配、最化的基板程序。

机器号

元件号

可以登在󲨉装数据上的元件号󱓖是 1-255。

Comparison Table ( English - Chinese )

Code

CodeCode

Code

English

EnglishEnglish

English

Chinese

ChineseChinese

Chinese

Component number

The parts number by which registration is possible

is 1-255 in mount data.

Ea03934

The code scanning data exists more than a regulated number.

存在󲚙定数以上的条󱓖描数据

Ea03935 Please correct the mark data.(Pcb CodeScan)

Mark information corresponding to the Pcb CodeScan doesn't exist or,

there is no mark data for the code scanning.

Mark No

󲣌修改󰓜󲢅数据(基板条󱓖描)

不存在符合基板条󱓖描的󰓜󲢅信息,

或󰓜󲢅数据不是条󱓖描用数据。

󰓜󲢅号󱓖 号

Ea03936 Please correct the mark data.(Block CodeScan)

Mark information corresponding to the Block CodeScan doesn't exist or,

there is no mark data for the code scanning.

Mark No

󲣌修改󰓜󲢅数据(拼条󱓖描)

不存在符合拼条󱓖描的󰓜󲢅信息,

或󰓜󲢅数据不是条󱓖描用数据。

󰓜󲢅号󱓖 号

Ea03937 Please correct the Pcb CodeScan position.

The following axis coordinates are outside range of motion.

Axis name

Please correct positional coordinates of the Pcb CodeScan

in range of motion.

󲣌修改基板条󱓖描位置

以下󲱉的坐󰓜在工作范外。

󲱉名称

󲣌把基板条󱓖描的位置坐󰓜修改到工作范内。

Ea03938 Please correct the Block CodeScan position.

Please correct the Pcb CodeScan position.

Axis name

Please correct positional coordinates of the Block CodeScan

in range of motion.

󲣌修改拼条󱓖描位置。

以下󲱉坐󰓜在工作范外。

󲱉名称

󲣌把拼条󱓖描的位置坐󰓜修改到工作范内。

Ea03939 Please correct the mark data.(Pcb CodeScan)

The height of recognition of the Pcb CodeScan

is outside range of motion.

Please confirm mark information.

Mark No

󲣌修改󰓜󲢅信息

基板条󱓖描的󲢛高度在工作范外。

󲣌确󲡹󰓜󲢅信息。

󰓜󲢅号󱓖

Ea03940 Please correct the mark data.(Block CodeScan)

The height of recognition of the Block CodeScan

is outside range of motion.

Please confirm mark information.

Mark No

󲣌修改󰓜󲢅信息

拼条󱓖描的󲢛高度在工作范外。

󲣌确󲡹󰓜󲢅信息。

󰓜󲢅号󱓖

Ea03942 DATA CHECK ERROR

Force Calibration Station Position(Y) exceeds Safety Pos.for

Camera(Machine Y Axis).

Please set it to less than Force Calibration Station Position(Y).

Please correct the machine settings and read same Board data.

Force Calibration Station Position(Y)

[Setting][Specification Information][Force Control Specification]

[Basic/Convert]

Safety Pos.for Camera(Machine Y Axis)

[Setting][Machine Data][Tray Changer][Position]

程序󰖕󰒺󳇮󲣄

󲧴荷校正站基准(Y)超出了相机安全位置(主机 Y 󲱉坐󰓜)。

󲣌󲢓置在相机安全位置(主机 Y 󲱉坐󰓜)以内。

󲣌正确󲢓置[机器󲢓置]画面，并重新󲣐入基板程序。

󲧴荷校正站基准(Y)

[机器󲢓置][󲚙格信息][󲧴荷控制󲚙格]

[基本/󲱁󰀷]

相机安全位置(主机 Y 󲱉坐󰓜)

[机器󲢓置][机器数据][托󱎭交󰀷器][位置坐󰓜]

Ea03959 MACS DATA ERROR

There is wrong parameter in mark database for Wafer Thermal MACS.

because of following reasons;

- Mark Type is not "Wafer Fiducial".

- Algorithm Type is "PTRN ?".

Database No.

MACS 数据󳇮󲣄

晶片󰷂校正 MACS 用󰓜󲢅数据异常。

可能是因下列原因所致。

- 󰓜󲢅󱥐型没有󲢓置"晶片基准󰓜󲢅"。

- 󲢛󱥐型的󲢓置"󰔌匹配"。

数据 号

Ea03962 DATA CHECK ERROR

3A Correction cannot work under the current condition.

Please check the following items.

[Print][Board][Board Fiducial] must not be [Not Use].

程序󰖕󰒺󳇮󲣄

使用当前的󲢓置,无法行 3A 校正。

󲣌确󲡹以下󳕎目。

[印刷]-[基板]-[基板基准󰓜󲢅]的󲢓置不是[不使用]。

Ea03963 DATA CHECK ERROR

3A Correction cannot work under the current condition.

Please check the following items.

[Print][Board][Fiducial Type] must be [2 Points].

程序󰖕󰒺󳇮󲣄

使用当前的󲢓置，无法行 3A 校正。

󲣌确󲡹以下󳕎目。

[印刷]-[基板]-[基准󰓜󲢅󱥐型]的󲢓置[2 点]。

Ea03964 DATA CHECK ERROR

3A Correction cannot work under the current condition.

Please check the following items.

[Print][Mask][Mask Fiducial] must not be [Not Use].

程序󰖕󰒺󳇮󲣄

使用当前的󲢓置，无法行 3A 校正。

󲣌确󲡹以下󳕎目。

[印刷]-[网板]-[网板基准󰓜󲢅]的󲢓置不是[不使用]。

Ea03965 DATA CHECK ERROR

3A Correction cannot work under the current condition.

Please check the following items.

[Print][Squeegee][F.&B.Mask Offset] must be [Same Offset].

程序󰖕󰨠󳇮󲣄

使用当前的󲢓置，无法行 3A 校正。

󲣌确󲡹以下󳕎目。

[印刷]-[刮刀]-[往返目󰨠偏移量]的󲢓置[往返同一指定]。

Ea04000 <<<WARNING SENSOR ERROR>>>

Head down sensor or Lower Sensor is OFF in C-table.

Please check sensor and remove the cause of

this sensor being OFF.

If you don't remove the cause, it is impossible

<<<警告 感器异常>>>

在 C 工作台，󰖕出了[吸嘴下降状]。

下降端或第 1 下降区域的感器呈 OFF 。

󲣌󰖕󰒺感器，排除󳇮󲣄原因。

如不排除󳇮󲣄原因，不能󲲰行自运行。

Comparison Table ( English - Chinese )

Code

CodeCode

Code

English

EnglishEnglish

English

Chinese

ChineseChinese

Chinese

to start production.

Ea04001 <<<WARNING SENSOR ERROR>>>

Head down sensor or Lower Sensor is OFF in D-table.

Please check sensor and remove the cause of

this sensor being OFF.

If you don't remove the cause, it is impossible

to start production.

<<<警告 感器异常>>>

在 D 工作台，󰖕出了[吸嘴下降状]。

下降端或第 1 下降区域的感器呈 OFF 。

󲣌󰖕󰒺感器，排除󳇮󲣄原因。

如不排除󳇮󲣄原因，不能󲲰行自运行。

Ea04002 FLYING NOZZLE CHECK POSITION ERROR

Current Z position for Flying Nozzle check is abnormal.

Possible causes are:

1.Something prevents the movement to the target Z position

2.In [Machine Data]-[Mechanical]-[Position],

InitPosition of Z axis is wrong.

Head No.

󳖳行式交󰀷吸嘴󲢛位置异常

󲢛当前󳖳行式交󰀷吸嘴的高度异常。

1.因存在干物，而不能移到目的地。

2.[机器󲢓置]-[机械坐󰓜]-[位置坐󰓜]

的 Z 󲱉初始移异常。

Head 号󱓖 号

Ea04003 FLYING NOZZLE ERROR

The condition of Flying Nozzle can't be confirmed.

It has the possibility of the sensor mis-response.

󳖳行式交󰀷吸嘴󲢛异常

不能确󲡹󳖳行式交󰀷吸嘴的状。

感器的反可能失󲣄了。

󲣌修感器。

Ea04004 FLYING NOZZLE ERROR

The condition of Flying Nozzle can't be confirmed.

It has the possibility of the sensor mis-response.

󳖳行式交󰀷吸嘴󲢛异常

不能确󲡹󳖳行式交󰀷吸嘴的状。

感器的反可能失󲣄了。

󲣌修感器。

Ea04005 MACHINE STATUS ERROR

The unusual state of a machine was detected.

Please save a file required for investigation.

机器状异常

󰖕󰨠到不恰当的机器状。

󲣌保存有必要󲣘󰒺的文件。

Ea04006 OPTIMIZATION ERROR

Failed to start optimization.

Component data

Name

Information No

适当󰒺找󳇮󲣄

适当󰒺找始失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04007 OPTIMIZATION ERROR

Failed to get the light status from vision system.

Component data

Name

Information No

适当󰒺找󳇮󲣄

从󲚛󲚞系󱮴取得照明条件失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04008 OPTIMIZATION ERROR

Failed to get component information from vision system.

Component data

Name

Information No

适当󰒺找󳇮󲣄

从󲚛󲚞系󱮴取得元件信息失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04009 OPTIMIZATION ERROR

Failed to send parameter to vision system.

Component data

Name

Information No

适当󰒺找󳇮󲣄

向󲚛󲚞系󱮴的参数送失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04010 OPTIMIZATION ERROR

Failed to save image for vision system.

Component data

Name

Information No

适当󰒺找󳇮󲣄

向󲚛󲚞系󱮴保存像失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04011 OPTIMIZATION ERROR

Failed to clear the memory of vision system.

Component data

Name

Information No

适当󰒺找󳇮󲣄

󲚛󲚞系󱮴的像内存清除失󲧺了。

元件数据号名称

󳇮󲣄󲢻󱮛 No

Ea04012 IONIZER WARNING

An error occurred with the ionizer.

Please confirm a state of an ionizer,

and consult your distributor for further information.

离子生器警告

离子生器生了异常。

󲣌确󲡹离子生器的状，并向制造厂商咨󲢷。

Ea04014 FLYING NOZZLE EXCHANGE ERROR

Unable to exchange flying nozzles.

Please consult your distributor.

Head No.

󳖳行式吸嘴交󰀷超󰋋󳇮󲣄

󳖳行式吸嘴不能󲲰行交󰀷。

󲣌向生厂家咨󲢷。

Head No. 号

Ea04015 TIME OUT ERROR TO CONFIRM HEAD UP

When the parts bring back check is executed, the head up was not confirmed

though the head move up.

Nozzle down limit sensor is illegal.(Full Air Machine.)

Nozzle down lower end sensor is illegal. Or it was not possible to move the

movable head height.(Full Servo Machine.)

Please resume operations after confirming the state of each sensor

󲨉装上升确󲡹超󰋋󳇮󲣄

󲨉装后，在回元件的󰖕󰒺中，󲍒然󲨉装正在上升，

但却没能确󲡹到󲨉装的上升作。

󲢺󳇮󲣄可能是由下列原因造成。

下降󳕛域的感器异常。(全气机)

下降端的感器异常，或󲨉装没有移到足的高度。(全伺服机器)

󲣌确󲡹各感器和伺服󲨉装后，重新始运行。

工作台号󱓖