YAMAHA 报警资料.pdf - 第19页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 19 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 18 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
it is impossible to use "Sp.Dump Back" for [Dump Way].
CMP No.(with alternative component)
Name
CMP No.(with "Sp.Dump Back")
Name
不能使用[特殊返理]。
替代元件指定元件号 名称
特殊返指定元件号 名称
Ea00293 COMPONENT DATA ERROR
[BGA ball data]file for this component does not exist.
This component needs [BGA ball data] file.
Component Name
Please make [BGA ball data] file.
元件数据
与元件数据的[BGA 球引脚信息]文件不存在。
元件必需使用[BGA 球引脚信息]文件。
元件名称
建[BGA 球引脚信息]数据。
Ea00295 DATA LOAD ERROR
Failed to load [BGA ball data].
Component data Name
In Draw Shape button of Adjust window, please
confirm [BGA ball data] file.
数据入
[BGA 球引脚信息]文件的入失了。
元件数据 号 名称
在助整的[定形状示]中，
确[BGA 球引脚信息]数据。
Ea00296 BOARD DATA ERROR
Setting of [Alignment Type] is [Undefined].
Please set [Alignment Type].
Component data Name
基板程序
[校正型][未置]。
置[校正型]。
元件数据 号 名称
Ea00297 BOARD DATA ERROR
Ext.TC or AutoTC is not available on
this machine.
Mount data
Component data Name
基板程序
因没有配置外部托交器或自托交器，
所以不能使用。
装数据 号
元件数据 号 名称
Ea00298 BOARD DATA ERROR
There is no dispense sequence for dot dispensing.
Check the head and unit
in 2-1-[Dot Disp. Info].
Dot Dispense data
基板程序
行正式点胶的作流程不存在。
在正式点胶画面确点胶和胶液量。
正式点胶数据 号
Ea00299 BOARD DATA ERROR
There is no dispense sequence for pre dispensing.
Check the head and unit
in 2-1-[Pre Disp. Info].
Pre Dispense data
基板程序
行点胶的作流程不存在。
在点胶画面确点胶和胶液量。
点胶数据 号
Ea00300 Tray unit error : The component is not placed
correctly on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
托交器∶没有将供元件正确放置在料站上。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00301 Tray unit error : Returned component is not placed
correctly on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 未能将返回的元件正确放置在料站上。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
Ea00302 Tray unit error : Failed to pick the component from
the tray.
The tray unit could not pick
from the following tray position:
Remove component from head.
Mount data
Component data Name
Pallet
Next tray position is for the next pick sequence.
(X= , Y= )
托交器: 未能从托上吸附元件。
如果托上有元件存在，取出。
如果有吸附状的元件，取出。
装数据 号
元件数据 号 名称
料架
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00303 Tray unit error : Failed to put the component
on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
托交器: 未能将元件正确放置在料站上。
如果料站上有元件，取出。
装数据 号
元件数据 号 名称
料站
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00304 Tray unit error : Failed to pick the component from
the traverser station.
If component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 未能从料站上吸附元件。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 19 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea00305 Tray unit error : Unknown component is
on the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 料站上放置了元件。
取出元件。
装数据 号
元件数据 号 名称
料站
Ea00306 Tray unit error : Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架退回收柜。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00307 Tray unit error : Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架从收柜中抽出。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00308 Tray unit error : Failed to start the Hook Action.
Please check the following items:
1. Pallet (No. ) access position.
2. The hook nail.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open..
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP" ON.
2. Remove the pallet from the stage section.
3. Return the pallet to its magazine.
托交器: 抓手未能正常作。
注意以下的目。
1．重新将料架(No. )放置在正确位置。
2．抓手的爪弯曲。
3．抓手感器的作不良。
4．收柜不能正常行收。
5．收的收柜柜敞状。
如料架出了收柜，按下列操作。
1．按下急停机按。
2．取出料架。
3．将料架放回收柜。
Ea00310 Tray unit : The tray unit head or traverser station
has a component attached to its nozzle (pad).
Please remove the component.
托交器: 外部托的 Head 或外部托
料站上存在元件，取出。
Ea00311 Tray unit error: Abort the RESET process.
If a pallet is out of the magazine, please remove it
and store it to its assigned magazine by hand.
托交器
因急停机，料架抽出作中断了。
Ea00313 Tray unit error: The pallet is out of the magazine.
Return the pallet to its assigned magazine.
托交器: 料架出了收柜。
将料架退回收柜。
Ea00314 Tray unit error: The door is open.
Please close the door.
托交器:柜敞着。
敞的柜。
Ea00315 Tray unit error: Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能将料架退回收柜。
将料架退回收柜。
Ea00316 Tray unit error: Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能从收柜中抽出料架。
将料架退回收柜。
Ea00317 TRAY CHANGER ERROR : The door is open.
The door is open or the Z-axis is servo-off.
Please close the door.
(When the door light is off in spite of the door switch 'close',
please make the door switch into 'open' once and make it 'close'.)
托交器 : 柜敞着。
柜敞着，或托交器的 Z 的伺服着。
敞着的柜。
(然柜[]，但柜指示灯不亮灯，
先将柜置[]，然后再置[]。)
Ea00318 Tray unit error : Failed to pick up components from
the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
If this error exist many times, please confirm following,
1.[YTF] Vacuum sensor of the traverser station
2.[SMT] Vacuum valve of the head
3.[TrayChanger] Z-axis
托交器:未能从料站吸附元件。
取出元件。
装数据 号
元件数据 号 名称
料站
如生，下列目。
1．[YTF] 料站的真空感器
2．[片机] 装的吸附
3．[托交器] 料站 Z 坐
Ea00330 The head of the machine or tray-changer is picking a
component. If "SET PALLET" is executed,
component will drop from head.
Remove component from head and execute "SET PALLET"
again.
机器或者托交器呈元件吸附状。
如果此抽出料架，元件可能会脱落。
取出吸附状的元件，并再次行。
Ea00331 TRAY CHANGER ERROR
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
托交器
因托交器陷于了危状或没有料到的状，所以不能重新始运行。
如料架从收柜中出，按下列恢原状。
1. 按急停机按
2. 用手取出料架
3. 按 READY 按
4. 打柜，将料架放回原位
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 20 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
5. Close the door 5. 柜
Ea00332 TRAY CHANGER ERROR
The operation of opening the door was interrupted by EMERGENCY STOP.
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP", Please open the door again and store the
pallet.
(If the door switch is already 'open',
Please make the door switch into 'close' once and make it 'open')
托交器
因急停机等原因，柜打作中断了。
料架可能不在正确的位置上。
解除急停机后，重新打柜装入料架。
(柜已置[]，先将柜置[]，
然后再置[]。)
Ea00333 TRAY CHANGER ERROR
The operation of manual pallet set was interrupted by emergency stop.
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP", Please make the door switch into 'close'
and store the pallet.
托交器
因急停机等原因，手抽出料架的作中断了。
料架可能不在正确的位置上。
解除急停机后，重新打柜放入料架。
Ea00334 TRAY CHANGER ERROR
There is no pallet required in the magazine.
Please check whether the pallet and the magazine are set correctly.
Pallet
托交器
收柜内没有必需的料架。
确料架及收柜是否已正确安装。
料架号 号
Ea00335 TRAY CHANGER ERROR
Can not start production because the operation of manual pallet set is not
completed.
Please put the pallet back in the magazine by opening the door again,
and restart the production.
托交器
因手料架安装作未完成，所以不能始自运行。
打柜安装好料架后，再次启自运行。
Ea00336 TRAY CHANGER ERROR
Can not start production because the operation of opening the door is not
completed.
Though door switch is 'Open', the palette has not been stored yet.
This error is caused by interruptions of opening the door by emergency stop, etc.
Please put the pallet back in the magazine by opening the door again,
and restart the production.
托交器
因以手方式安装料架的作未完成，所以不能始自运行。
柜""，但本收在收柜中的料架却抽出状。
状生在因急停机而引起中断柜打。
打柜安装好料架后，重新始自运行。
Ea00337 Tray changer door opening warning
The magazine rack may not move to the drawer position,
because the door switch was operated quickly.
Please make the door switch into 'close' once (the door light lights),
and make it 'open' again.
托交器柜打警告
因快按柜，所以收柜料箱可能未到达抽出位置。
先将柜置''，等柜指示灯点亮后，再置''。
Ea00338 Tray changer magazine set warning
The magazine rack is not set correctly.
Please check the following points.
1. The magazine clamp must be locked correctly.
2. The pallet suppression of the magazine must be tightened correctly.
3. The pallet not protruding from the magazine.
托交器 收柜安装警告
收柜料箱没有安装好。
确以下目。
1. 收柜固定已。
2. 收柜的料架板已。
3. 料架没有出收柜。
Ea00339 Tray changer door closing warning
The door was closed with the door switch 'close'.
In this state, the tray changer may not work.
Please make the door switch into 'open', and make it 'close' again.
托交器 柜警告
在柜''的状下了柜。
在此状下，托交器可能不能作。
先将柜置''，然后再置''。
Ea00340 TRAY CHANGER DOOR OPENING ERROR
Can not open the door because of the INTERLOCK error.
Please make the door switch 'open' and remove the cause of the INTERLOCK error.
Then please make the door switch 'close' once again.
托交器 柜警告
因正在状，所以不能打柜。
在此状下，托交器可能不能作。
先将柜置''，等排除原因后，
再置''。
Ea00351 INTERLOCK ERROR
The tray unit pallet is out of the magazine.
When you press [READY], you must check the following.
1. Are conditions safe for other people?
2. Are you outside the machine's moving area?
3. Have you returned the pallet to the magazine?
托交器的料架从收柜中出。
按[READY]，注意以下的事。
1．其他人是否在工作
2．是否确保了机械的作范
3．是否已将料架退回收柜
Ea00352 ORIGIN INCOMPLETE
When you press [READY], you must check the following.
1. Are conditions safe for other people?
2. Are you outside the machine's moving area?
3. Have you returned the pallet to the magazine?
返回原点
托交器的料架从收柜中出。
按[READY]，注意以下的目。
1．其他人是否在工作
2．是否确保了机器的作范
3．料架是否已退回收柜
Ea00363 NO COMPONENT FOR USE
All components in alternative loop are not available.
This can be caused by the following:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Tray start No.
Tray end No.
替代元件循的所有元件已不可使用的状。
原因如下:
- 生了吸附或。
- 使用的元件数量已达到指定的数量。
充下列元件后，重新始运行。
元件数据号 号
托始号 号
托束号 号
Ea00365 NO COMPONENT FOR USE 替代元件循的所有元件已不可使用的状。