YAMAHA 报警资料.pdf - 第220页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 220 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 219 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea25623 Take over file write-in error
Writing of take over file went wrong.
移交文件写入
移交文件的写入失了。
Ea25624 Take over file reading error
Reading of take over file went wrong.
移交文件入
移交文件的入失了。
Ea25625 Manual Select plan
The following ID information was set up.
ASSY:%s
Surface Information:%s
Program Name:%s
Board Count:%d
Creation time:%s
Do you want to plan it from this information?
品指定切
已置了下列 ID 信息。
ASSY 号 :%s
生面信息 :%s
程序名称 :%s
定生枚数:%d
生成日期 :%s
用信息行生品切?
Ea25626 Auto Plan Change
It changes to an auto plan "No Use."
Please use this mode to choose a plan manually.
However, when it changes into "No Use", it will be in the following states.
- Board Id is deleted altogether.
- Production number of sheets and production schedule number of sheets are reset.
- It cannot return to the state before change.
Is it all right?
自切生品功能的切
将自切生品功能置[不使用]。
如要用手切生品，使用模式。
但，更改[不使用]，将成以下状。
- 将除全部基板 ID。
- 生枚数、定生枚数将初始化。
- 不能原至切前的状。
确行?
Ea25627 Auto Plan Change
It changes to an auto plan "Use."
Please use this mode to perform an auto plan.
Is it all right?
自切生品功能的切
将自切生品功能置[使用]。
如果要使用自切生品功能，模式。
确行?
Ea25628 Auto Plan Change
It is an auto plan "Use."
In this mode, it does not correspond to the plan selection in manual operation.
Please change auto plan use mode into "No Use"
from ID monitor or choose "Yes" to perform plan selection.
However, when it changes into "No Use", it will be in the following states.
- Board Id is deleted altogether.
- Production number of sheets and production schedule number of sheets are reset.
- It cannot return to the state before change.
Do you want to perform plan selection in manual operation?
自切生品功能的切
自切生品功能于[使用]状。
模式下，不能用手切生品。
如要手，从 ID 控屏将自切生品功能的
使用模式更改[不使用]，或[是]。
但，更改[不使用]，将成以下状。
- 将除全部基板 ID。
- 生枚数、定生枚数将初始化。
- 不能原至切前的状。
可以行用手方式切生品?
Ea25629 Auto Plan Change
It is an auto plan "Not Use."
The usual production will be started if auto running is started as it is.
Please change to an auto plan "Use" to perform production
which used the auto plan.
Do you want to change to an auto plan "Use"?
自切生品功能的切
自切生品功能于[不使用]状。
如在状下行自运行，将行通常的生。
若要使用自切生品功能行生，
将自切生品功能置[使用]。
确将自切生品功能置[使用]?
Ea25630 Program list file access failure.
Since other equipment or external PC is using the program list,
it cannot be edited. Please stop editing by corresponding equipment.
Equipment under edit:
不能程序列
其他或外部的 PC 正在使用程序列，所以不能。
在相上中止。
正在的:
Ea25631 Board ID reading error
Reader Index : 1
Status : %s
Reading Result: %s
Reader Index : 2
Status : %s
Reading Result: %s
Please retry or input Board ID manually.
基板 ID 信息取
器号: 1
状 : %s
取果 : %s
器号: 2
状 : %s
取果 : %s
重新行或手入 ID 信息。
Ea25632 Auto Plan Change
It is an auto plan "Use."
In this mode, it does not correspond to the plan selection in manual operation.
Please perform the following procedure to change auto plan mode into "No Use."
1. Reset by taking out all board from inside of machine.
2. Change auto plan use mode into "No Use" from ID Monitor.
自切生品功能的切
自切生品功能于[使用]状。
模式下，不能使用手切生品。
如要将自切生品功能更改[不使用]，
按如下行。
1.将机器内全部基板出，并行位。
2.在 ID 控屏中将自切生品功能的使用模式更改[不使用]。
Ea25633 Auto Plan mode change
Auto plan mode is changed.
Change of Auto plan mode deletes all of ID information,
the production number of sheet, and the production plan number of sheet.
When you start production, please reread production kind information.
When Auto plan mode is "None", please start production in the usual procedure.
切模式的更改
更改切模式。
如果更改切模式，全部 ID 信息、生枚数、定生
枚数将被除。
始生，重新入生品信息。
[不使用自切生品]，按通常的序始生。
Ea25634 Auto Plan start error
In the state where there is no production kind information,
Board was detected at the last process.
Auto plan cannot be started with this.
Since production kind information is reread, please start production.
自切生品功能始
没有生品信息的状下，在前道工序中出了基板。
在此状下无法始自切生品功能。
重新入生品信息后，再始行生。
Ea25635 Production Plan error
Production for schedule number of sheets is not completed.
生枚数
没有达到定生枚数。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 220 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Although production of a stock-in-hand kind cannot be continued
when auto plan mode is changed, do you want to chage auto plan mode?
更改切模式后，不能当前品的生。
需要更改切模式?
Ea25636 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in sub stopper position.
Automatic plan operation can't be continued.
Remove the board of sub stopper position.
无基板 ID 信息
待机位置不存在基板 ID 信息。
在此状下无法用自切生品功能行运行。
取出待机位置的基板。
Ea25637 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in upper buffer conveyor position.
Automatic plan operation can't be continued.
Remove the board of upper buffer conveyor position.
无基板 ID 信息
上冲送位置上不存在基板 ID 信息。
在此状下无法使用自切生品功能行运行。
取出上冲送装置上的基板。
Ea25638 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in main stopper position.
Automatic plan operation can't be continued.
Remove the board of main stopper position.
无基板 ID 信息
印刷位置不存在基板 ID 信息。
在此状下无法使用自切生品功能行运行。
取出印刷位置上的基板。
Ea25639 Auto plan start error
The error occurred during the automatic plan change.
The current board data differs from the program name
contrasted from production kind information.
Production of as it is present is uncontinuable.
When you resume production, please cope with it as follows.
1.Automatic plan use mode is changed into "No Use."
2.Board data is reread from a Setup screen.
3.Automatic plan use mode is changed into "Use."
4.Automatic operation is resumed and
production kind information is reread.
自切生品功能始
在切自切生品功能中生了。
当前入的基板程序与生品信息所的程序名称不一致。
无法当前的生。
如重新始生，按照如下行。
1.将自切生品功能的使用模式更改[不使用]。
2.在生画面重新入基板程序。
3.将自切生品功能的使用模式更改[使用]。
4.重新始自运行，重新入生品信息。
Ea25640 Auto plan warning
The error occurred during automatic plan operation.
Please cope with it as follows and
check the contents of an error displayed.
-It stands by until all the Board in a machine are conveyed.
-Auto running is stopped.
自切生品警告
使用自切生品功能行运行的程中生了。
按照如下方法之一，确示的内容。
·使机器置于待机状，直至机器内的基板全部出止。
·停止自运行。
Ea25641 NO BOARD DATA
Although automatic reading of a dummy board was performed,
the specified Board data does not exist.
BOARD DATA %s
无基板程序
行了虚基板的自入，但指定的基板程序
没有登在机器中。
基板程序 %s
Ea25642 Auto Plan start error
In the state where there is no production kind information,
Auto plan was started.
Auto plan cannot be started with this.
Since production kind information is reread, please start production.
自切生品功能始
在没有生品信息的状下，始了自运行。
在此状下无法始自切生品功能。
重新入生品信息后，再始生。
Ea25643 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
It is an auto plan "Not Use."
Please change to an auto plan "Use".
条板 ID 取
不能取条板 ID。
原因
自切生品功能于[不使用]状。
将自切生品功能切[使用]。
Ea25644 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
Next ASSY information has already been registered.
Please cancel registered information when you want to
register ASSY information again.
Please reset it when you want to cancel.
条板 ID 取
不能取条板 ID。
原因
已登了下个品信息。
重新登品信息，
将已登品信息取消。
若要取消，先初始化。
Ea25645 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
The error occurred during automatic plan operation.
Please cope with it as follows and
check the contents of an error displayed.
-It stands by until all the Board in a machine are conveyed.
-Automatic operation is stopped.
条板 ID 取
不能取条板 ID。
原因
使用自切生品行运行的程中生了。
按照下列方法之一，确所示的内容。
·置于待机状，直至机器内的基板全部送完止。
·停止自运行。
Ea25646 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
KANBAN ID cannot be read at a present operator level.
Please operate it by the operator to whom the readout
of KANBAN ID is permitted.
条板 ID 取
不能取条板 ID。
原因
当前的操作不能取条板 ID。
由允取条板 ID 的操作者行操作。
Ea25647 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
A Board or Board ID information exists in equipment.
Please reset it after removing all Board and Board ID information
in equipment.
条板 ID 取
不能取条板 ID。
原因
内存在基板、或 ID 信息。
将内的基板、或 ID 信息全部除。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 221 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea25648 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
Emergency Stop Function Is Active.
Check for safe conditions and
press the READY button to
re-enable the machine.
条板 ID 取
不能取条板 ID。
原因
急停机正在作用。
确安全，并按急停机解除按。
Ea25650 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
The Board program name and current Board program name of a take over File differ
from each other.
Please, check the following data.
Board name in take over file %s
自切生品功能 坏板信息送
移交文件的基板程序名和当前的基板名不一致。
确移交文件。
移交文件的基板程序名：%s
Ea25651 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
The number of BLOCK BADMARK of a take over file is not in agreement with the
contents registered into the board.
Please, check the following data.
BLOCK BADMARK data in take over file.
自切生品功能 坏板信息送
移交文件的拼坏板数和基板登内容不一致。
确移交文件。
Ea25652 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
The number of LOCAL BADMARK of a take over file is not in agreement with the
contents registered into the board.
Please, check the following data.
LOCAL BADMARK data in take over file.
自切生品功能 坏板信息送
移交文件的局部坏板数和基板登内容不一致。
确移交文件。
Ea25653 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
No BADMARK transmission data in take over file.
Please, check the following data.
BADMARK data in take over file.
自切生品功能 坏板信息送
移交文件中不存在坏板送信息。
确移交文件。
Ea25654 The Board has been lost.
The Board on the lower buffer conveyer has been lost at the following position.
[Check position]
Please return the Board to former position according to the
position of ID information.
Please delete ID information when you remove the Board as it is.
ID information on the conveyer can be confirmed by the ID monitor.
失了基板
在下位机冲送装置的下列位置上，失了基板。
[位置]
根据 ID 信息的位置，将基板放回原来的位置。
如立即取出基板，除 ID 信息。
送装置上的 ID 信息，可在 ID 控屏行确。
Ea25655 Illegal Board was detected.
An illegal Board was detected on the lower buffer conveyer at the following position.
[Check position]
Please remove an illegal Board without ID information.
ID information on the conveyer can be confirmed by the ID monitor.
出的基板不正确
在下位机冲送装置的下列位置上，出了基板。
[位置]
取出没有 ID 信息的基板。
送装置上的 ID 信息，可在 ID 控屏行确。
Ea25656 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
Failed to get Board BADMARK data.
自切生品功能 坏板信息送
基板坏板信息的取失了。
Ea25657 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
Failed to get BLOCK BADMARK data.
自切生品功能 坏板信息送
拼坏板信息的取失了。
Ea25658 AUTO PLAN BADMARK INFORMATION TRANSMISSION ERROR
Failed to get LOCAL BADMARK data.
自切生品功能 坏板信息送
局部坏板信息的取失了。
Ea25659 Put In Board
It puts in the following Board removed in the past.
Lot Num:%d
Serial Num:%s
Board Count:%d
Mounting Status:%s
Removed Time:%s
Removed Equipment:%s
Please check a Board and put in %s.
基板的中途投入
中途投入以前曾取出的下列基板。
批号 :%d
序列号 :%s
定生枚数:%d
装状 :%s
取出 :%s
取出 :%s
确基板并投入到%s。
Ea25660 Removed Board Id Delete
Do you want to delete Removed Board Id of the line chosen now?
除取出基板 ID
除当前所行的取出基板 ID ?
Ea25661 Put In Board Error
Removed Board Id chosen now does not already exist
by the deletion from other equipment, or automatic deletion.
中途投入
当前的取出基板 ID 已被其他或自除功能
所除，已不存在了。
Ea25662 Kind Mismatch of The Board Id To Put In
The Board to put in was detected as production kind information differed.
Assy:%s
Surface Information:%s
Program Name:%s
Does it plan from this information?
中途投入基板的品不一致
出了与生品信息不一致的中途投入基板。
Assy 号 :%s
生面信息 :%s
生程序名 :%s
用信息行生品切?
Ea25663 Auto Plan Invalid Path Error
The following automatic plan setting path is an invalid path.
Please change into an effective path.
%s
自切生品功能 置路径无效
以下自切生品功能的置路径无效路径。
更改有效的路径。
%s
Ea25664 Program List File Write Failure
The writing of a file went wrong.
Please check the state of a file and edit again.
程序列写入
程序列的写入失了。
确文件的状，并重新行。
Ea25665 Program List UnSaved 程序列文件未保存