YAMAHA 报警资料.pdf - 第145页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 145 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 144 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Es00075 Es00075:EncoderBreak A
--- CAUSE ---
The encoder cable wiring is broken.
The servo-motor or servo-board is defective.
--- COUNTERMEASURE ---
Check the encoder cables.
Replace the servo-motor or servo-board.
Es00075: 󱯫󱓖器断󱮔 A 相
原因:
󱯫󱓖器󱈊󱯛的断󱮔
伺服󳝁达、伺服卡的异常
策:
󰖕󰒺󱯫󱓖器󱈊󱯛
更󰀷伺服󳝁达、伺服卡
Es00076 Es00076:Position deviation overflow
Servo-motor not responding to commands from servo-board.
--- CAUSE ---
Mechanical locking in motor-axis.
Failure in connecting motor-encoder cables.
Failure in connecting motor-power cables.
The servo-motor is defective.
The servo-board or the driver-board is defective.
Short in power supply capacity.
--- COUNTERMEASURE ---
Check the mechanical friction in motor-axis.
Check the motor-encoder and motor-power cables.
Replace motor,cable,servo-board,or driver-board.
Check the voltage and capacity of power supply.
Es00076:位置偏差溢出
伺服󳝁达伺服卡的指令没有充分答。
原因:
·机械󳝁达󲱉的上󳇖
·󱯫󱓖器󱈊󱯛的断󱮔、󳇮󲣄配󱮔
·󳝁达󱈊源󱮔的断󱮔、󳇮󲣄配󱮔
·伺服󳝁达的异常
·伺服卡或󳝆卡的异常
·󱈊源容量不足
策:
·确󲡹机械󳝁达󲱉的上󳇖
·确󲡹󱯫󱓖器󱈊󱯛、󳝁达󱈊源󱮔的配󱮔
·更󰀷󳝁达、󱈊󱯛、伺服卡或󳝆卡
·确󲡹󱈊源󱈊、容量
Es00077 Es00077:Servo Checksum Err
Please consult your distributor for further information.
--- CAUSE ---
Servo cannot receive data from System correctly.
Es00077:伺服󰖕󰒺合󲡶󳇮󲣄
󲣌向制造商咨󲢷。
原因:
在伺服接收数据生了异常。
Es00078 Es00078:Servo DownLoad Err
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in controller.
Es00078:伺服下󲱒󳇮󲣄
󲣌向制造商咨󲢷。
原因:
控制器内部异常。
Es00079 Es00079:SrvCom cable Err
The servo communication cable is broken.
--- CAUSE ---
The servo communication cable is broken.
The SERVO-IF board or the REMOTE-SERVO board is defective.
--- COUNTERMEASURE ---
Check the servo communication cables.
Check the LEDs on the SERVO-IF board and on the REMOTE-SERVO board.
Replace the SERVO-IF board or the REMOTE-SERVO board.
Es00079:伺服通信断󱮔
󰖕󰨠出伺服通信󱮔断󱮔了。
--- 原因 ---
伺服通信󱮔的断󱮔
伺服-IF 端口、󲲱程伺服端口异常
--- 策 ---
󰖕󰒺伺服通信󱮔
确󲡹伺服-IF 端口、󲲱程伺服端口的 LED
更󰀷伺服-IF 端口、󲲱程伺服端口
Es00080 Es00080:Encoder CS Err
The initial position data of encoder (CS DATA) is abnormal.
--- CAUSE ---
Fail in connecting motor-encoder cables.
The encoder cable wiring is broken.
The servo-motor or servo-board is defective.
--- COUNTERMEASURE ---
Check the encoder cables.
Replace the servo-motor or servo-board.
Es00080:󱯫󱓖器 CS 󳇮󲣄
󱯫󱓖器的初始位置数据(CS)异常。
--- 原因 ---
󱯫󱓖器󱮔的󳇮󲣄配󱮔
󱯫󱓖器󱮔的断󱮔
伺服󳝁达的异常
伺服端口的异常
--- 策 ---
󰖕󰒺󱯫󱓖器󱮔的配󱮔
更󰀷伺服󳝁达、伺服端口
Es00081 Es00081:48V motor power fail
Voltage of 48V for motor power is out from DC29V-60V
--- CAUSE ---
The SW power supply for 48V is defective.
The IF board or remote-servo board is defective.
The circuit-protector off.
--- COUNTERMEASURE ---
Check circuit-protector
Replace the servo-motor or servo-board.
Es00081:󳝁达󱈊异常 48V
48V 系列󳝁达的󱈊异常。
--- 原因 ---
48V 󱈊源的异常
󲲱程伺服端口或 IO 端口的异常
󱈊路保器的 OFF
--- 策 ---
󰖕󰒺󱈊路保器
更󰀷伺服󳝁达、伺服端口
Es00082 Es00082:Encoder Pulse Error
The encoder count is abnormal
--- CAUSE ---
The encoder cable wiring is broken.
The servo-motor or servo-board is defective.
--- COUNTERMEASURE ---
Check the encoder cables.
Replace the servo-motor or servo-board.
Es00082:󱯫󱓖器脉冲异常
󱯫󱓖器脉冲异常。
--- 原因 ---
󱯫󱓖器脉冲松落
󱯫󱓖器󱮔的断󱮔
伺服󳝁达的异常
伺服端口的异常
--- 策 ---
󰖕󰒺󱯫󱓖器󱮔
更󰀷伺服󳝁达、伺服端口
Es00083 Es00083:Application watchdog error
A servo detected a hang-up of application software.
--- CAUSE ---
--- COUNTERMEASURE ---
Power ON again.
Es00083:󲱄件󱎦󲚛󳇮󲣄
󰖕出了󲱄件中止󳇮󲣄。
原因:
󲱄件异常。
策:
重新接通󱈊源
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 145 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please consult your distributor for further information. 󲣌向厂商咨󲢷。
Es00084 Es00084:IPM short-circuit error
A servo board detected a short circuit of the IPM on driver board.
--- CAUSE ---
A power module on driver board is defective.
--- COUNTERMEASURE ---
Replace the driver board.
Es00084:IPM 短路󳇮󲣄
󰖕󰨠出󲢓󱈊路板上的 IPM 短路了。
原因:
󲢓󱈊路板上的元件生故障
策:
更󰀷󲢓󱈊路板
Es00100 Es00100: Es00100:
Es00101 Es00101:Disk Write Protected
--- CAUSE ---
Write protect of the floppy disk is active.
--- COUNTERMEASURE ---
Release Write protect of the floppy Disk.
Es00101:磁󱎭写入禁止
原因:
磁󱎭󲢓置了写保。
策:
󲣌解除磁󱎭的写保。
Es00102 Es00102:Drive Not Available
--- CAUSE ---
The path can't be found.
--- COUNTERMEASURE ---
Check the path.
Es00102:󳝆󱎭不存在
原因:
指定了不存在的󳝆󱎭。
策:
󲣌确󲡹指定的󳝆󱎭。
Es00103 Es00103:Drive Not Ready
--- CAUSE ---
there is no file in Drive A.
--- COUNTERMEASURE ---
Put the floppy disk into Drive A.
Es00103:󳝆󱎭未完成准
原因:
指定的󳝆󱎭中没有插入磁󱎭。
策:
󲣌在指定的󳝆󱎭中插入磁󱎭。
Es00104 Es00104:Invalid Disk Command
Please consult your distributor for further information.
Es00104:没有指定磁󱎭指令
󲣌向制造商咨󲢷。
Es00105 Es00105:CRC Error
Please consult your distributor for further information.
Es00105:CRC 󳇮󲣄
󲣌向制造商咨󲢷。
Es00106 Es00106:Invalid Command Length
Please consult your distributor for further information.
Es00106:指令󳉔度溢出
󲣌向制造商咨󲢷。
Es00107 Es00107:Seek Error
--- CAUSE ---
Write protect of the floppy disk is Effective.
--- COUNTERMEASURE ---
Release Write protect of the floppy Disk.
Es00107:󰒺找󳇮󲣄
原因:
在文件的中途，󲲰行了󲣐入或写入。
策:
󲣌再次󲲰行文件的操作。如仍然出󱂅󲢺󳇮󲣄，
󲣌与制造商󱴩系。
Es00108 Es00108:Disk Not MS-DOS Es00108:󲱄󱎭格式异常
原因:
正在使用的󲱄󱎭不是 1.4M 格式。
策:
󲣌使用 1.4M 格式的󲱄󱎭。
Es00109 Es00109:Sector Not Found Es00109:磁󱎭不能使用
正在使用的󲱄󱎭没有格式化。。
原因:
·正在使用的󲱄󱎭不是 1.4M 格式。
策:
·󲣌使用新的󲱄󱎭。
·󲣌将󲱄󱎭格式化成 1.4M。
Es00110 Es00110:No Paper
Please consult your distributor for further information.
Es00110:没有卷󱮍
󲣌向制造商咨󲢷。
Es00111 Es00111:Write Fault
--- CAUSE ---
This floppy disk has a trouble.
This floppy disk isn't formatted by 1.4M type.
--- COUNTERMEASURE ---
Use the new floppy disk.
Use the floppy disk formatted by 1.4M type
Es00111:写入失󲧺了
原因:
·正在使用的󲱄󱎭中有异常。
·正在使用的󲱄󱎭不是 1.4M 格式。
策:
·󲣌使用新的󲱄󱎭。
·󲣌使用󲲰行了 1.4M 格式化的󲱄󱎭。
Es00112 Es00112:Read Fault
--- CAUSE ---
This floppy disk has a trouble.
This floppy disk isn't formatted by 1.4M type.
--- COUNTERMEASURE ---
Use the new floppy disk.
Use the floppy disk formatted by 1.4M type
Es00112:󲣐入失󲧺了
原因:
·正在使用的󲱄󱎭异常。
·正在使用的󲱄󱎭不是 1.4M 格式。
策:
·󲣌使用新的󲱄󱎭。
·󲣌使用󲲰行了 1.4M 格式化的󲱄󱎭。
Es00113 Es00113:General Failure
Please consult your distributor for further information.
Es00113:一般󳇮󲣄
󲣌向制造商咨󲢷。
Es00114 Es00114:Unknown Error
Please consult your distributor for further information.
Es00114:󳇮󲣄原因不明
󲣌向制造商咨󲢷。
Es00115 Es00115:No Such File
--- CAUSE ---
There is not the objective file.
--- COUNTERMEASURE ---
Check the objective file.
Es00115: 没有的文件
原因:
指定的文件不存在
策:
󲣌确󲡹指定的文件。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 146 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Es00116 Es00116:Argument List Too Long
Please consult your distributor for further information.
Es00116:启󲳞󳕎󲲜大
󲣌向制造商咨󲢷。
Es00117 Es00117:Exec File Format Error
Please consult your distributor for further information.
Es00117:行格式󳇮󲣄
󲣌向制造商咨󲢷。
Es00118 Es00118:Bad File Number
Please consult your distributor for further information.
Es00118:文件号󱓖异常
󲣌向制造商咨󲢷。
Es00119 Es00119:Not Enough Memory
Please consult your distributor for further information.
Es00119:内存不足
󲣌向制造商咨󲢷。
Es00120 Es00120:Permission Denied
Please consult your distributor for further information.
Es00120:文件操作不可
󲣌向制造商咨󲢷。
Es00121 Es00121:File Exists
--- CAUSE ---
There is not the objective file.
--- COUNTERMEASURE ---
Check the objective file.
Es00121:文件已󱮤存在
原因:
与指定文件同名的文件已󱮤存在。
策:
与指定文件同名的文件已󱮤存在。
Es00122 Es00122:Cross Device Link
Please consult your distributor for further information.
Es00122:󲢓󳇓接󳇮󲣄
󲣌向制造商咨󲢷。
Es00123 Es00123:Invalid Argument
Please consult your distributor for further information.
Es00123:启󲳞󳕎无效
󲣌向制造商咨󲢷。
Es00124 Es00124:Too Many Open Files
Please consult your distributor for further information.
Es00124:打文件󲲜大
󲣌向制造商咨󲢷。
Es00125 Es00125:Disk Full
--- CAUSE ---
The diskspace of the floppy disk is full.
It is impossible to write more data to it.
--- COUNTERMEASURE ---
Use the new floppy disk.
Es00125:磁󱎭已󰮶
原因:
󲱄󱎭没有空余空󳋉，不能写入。
策:
󲣌准新的󲱄󱎭。
Es00126 Es00126:Math Argument
Please consult your distributor for further information.
Es00126:引数󳇮󲣄
󲣌向制造商咨󲢷。
Es00127 Es00127:Argument Overflow
Please consult your distributor for further information.
Es00127:引数溢出
󲣌向制造商咨󲢷。
Es00128 Es00128:Resource Deadlock
Please consult your distributor for further information.
Es00128:原代󱓖死󳇖
󲣌向制造商咨󲢷。
Es00129 Es00129:Directory Change Error
Please consult your distributor for further information.
Es00129:不能更改目
󲣌向制造商咨󲢷。
Es00130 Es00130:Drive Change Error
Please consult your distributor for further information.
Es00130:不能更改󳝆
󲣌向制造商咨󲢷。
Es00131 Es00131:Directory Exist
--- CAUSE ---
There is a same directory with the objective directory.
--- COUNTERMEASURE ---
Change the name of the objective directory.
Es00131: 存在同名目
原因:
与指定目同名的目已存在。
策:
󲣌更改指定目的名称。
Es00132 Es00132:Directory Make Error
Please consult your distributor for further information.
Es00132:不能生成目
󲣌向制造商咨󲢷。
Es00133 Es00133:Directory Remove Error
--- CAUSE ---
There is a file in the objective directory.
--- COUNTERMEASURE ---
Delete the file of ateChange the name of the objective directory.
Es00133:不能除目
原因:
指定的目中有文件存在。
策:
󲣌除指定目中的文件。
Es00134 Es00134:Rename Error
Please consult your distributor for further information.
Es00134:不能更改名称
󲣌向制造商咨󲢷。
Es00200 \\x1b[41mIO WARNING: \\x1b[41mIO WARNING:
󲣌向制造商咨󲢷。
Es00201 Es00201:KG2-42S9 File Open Error
Please consult your distributor for further information.
Es00201:KG2-42S9 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00202 Es00202:KG2-42S8 File Open Error
Please consult your distributor for further information.
Es00202:KG2-42S8 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00203 Es00203:KG2-42S7 File Open Error
Please consult your distributor for further information.
Es00203:KG2-42S7 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00204 Es00204:KG2-58D9 File Open Error
Please consult your distributor for further information.
Es00204:KG2-58D9 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00205 Es00205:KG2-58D9 File Open Error
Please consult your distributor for further information.
Es00205:KG2-58D9 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00206 Es00206:KG2-42S7 File Open Error
Please consult your distributor for further information.
Es00206:KG2-42S7 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00207 Es00207:KG2-42S9 File Close Error
Please consult your distributor for further information.
Es00207:KG2-42S9 文件打󳇮󲣄
󲣌向制造商咨󲢷。
Es00208 Es00208:KG2-42S8 File Close Error
Please consult your distributor for further information.
Es00208:KG2-42S8 文件󳋂󳇮󲣄
󲣌向制造商咨󲢷。
Es00209 Es00209:KG2-42S7 File Close Error
Please consult your distributor for further information.
Es00209:KG2-42S7 文件󳋂󳇮󲣄
󲣌向制造商咨󲢷。
Es00210 Es00210:KG2-42S7 File Close Error Es00210:KG2-42S7 文件󳋂󳇮󲣄