YAMAHA 报警资料.pdf - 第219页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 219 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 218 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
The Board on the lower buffer conveyer has been lost at the following position.
[Exit position]
Please return the Board to former position according to the
position of ID information.
Please delete ID information when you remove the Board as it is.
ID information on the conveyer can be confirmed by the ID monitor.
在下流冲送装置的下列位置上，失了基板。
[出口位置]
参照 ID 信息的位置，将基板放回原来的位置。
如立即取出基板，除 ID 信息。
送装置上的 ID 信息，可在 ID 控屏行确。
Ea25610 Illegal Board was detected.
An illegal Board was detected on the lower buffer conveyer at the following position.
[Exit position]
Please remove an illegal Board without ID information.
ID information on the conveyer can be confirmed by the ID monitor.
出的基板不正确
在下流冲送装置的下列位置上，出了基板。
[出口位置]
取出没有 ID 信息的基板。
送装置上的 ID 信息，可在 ID 控屏行确。
Ea25611 Board ID Illegal
Inputted ID is inaccurate.
Please retry or input Board ID manually.
Board ID: %s
基板 ID 信息不正确
入的 ID 信息不正确。
重新行或手入 ID 信息。
ID 信息: %s
Ea25612 deletion confirmation.
Do you remove the line chosen at present?
除确
确要除当前所行?
Ea25613 Board Data re-reading under APCO
It is under operation using an automatic plan.
Is the present board data re-read?
[Yes] The board data under selection is re-read.
[No] It moves to the check of board selection.
Current Board Data: %s
自切生品运行中 基板程序再入
正在使用自切生品功能运行机器。
重新入当前的基板程序?
[是] 重新入当前所基板程序
[否] 移至基板确画面
当前的基板程序: %s
Ea25614 PRODUCTION PLAN ERROR
The board for the next production is detected
before current production does not reach for the
count of plan.
Do you want to switch the next production?
生枚数
完成定生枚数前，出了下一个生品信息。
是否切上道工序出口所出的生品生?
Ea25615 PRODUCTION PLAN ERROR
The board detected is over count of the current
plan.
生枚数
出了超定生枚数的基板生品信息。
Ea25616 LOT END
Specified number of Board is finished.
定生枚数束
已生完所指定枚数的基板。
Ea25617 INITIALIZE ERROR OF AUTO PLAN
Reading of a command definition file went wrong.
Please check whether a file exists.
This file is required when plan mode is "Board Id plan".
Please change plan mode, when this file is unnecessary.
File path
%s
自切生品 初始化理
指令定文件的入失了。
确文件是否存在。
文件在切模式[基板 ID 切]必使用。
如不需要，更改切模式。
文件路径
%s
Ea25618 FIRST Board CHECK
Please check first pcb of a lot by moving
camera. Press the [OK] button to check,
or [CANCEL] button to abort.
After checking and correcting, please start
production.
首件模式
利用移相机目一批品中首件的装状。
行按[OK]，中止按[取消]。
束后，重新始自运行。
Ea25619 FINAL Board CHECK
Please check last pcb of a lot by moving
camera. Press the [OK] button to check,
or [CANCEL] button to abort.
After checking and correcting, please start
production.
末件模式
利用移相机目一批品中末件的装状。
行按[OK]，中止按[取消]。
束后，重新始自运行。
Ea25620 INTERVAL Board CHECK
Please check specified pcb of a lot by moving
camera. Press the [OK] button to check,
or [CANCEL] button to abort.
After checking and correcting, please start
production.
指定枚数模式
利用移相机目指定批次的装状。
行按[OK]，中止按[取消]。
确束后，重新始自运行。
Ea25621 INITIALIZE ERROR OF AUTO PLAN
Reading of Board Id information item definition file went wrong.
Please check whether a file exists.
File path
%s
自切生品功能 初始化理
基板 ID 信息目定文件的入失了。
确文件。
文件路径
%s
Ea25622 INITIALIZE ERROR OF AUTO PLAN
Communication port did not open.
Please check a setup of command definition file or check whether
it's equipped with the extended communication board.
This communication port is required
when plan mode is "Board Id plan".
Please change plan mode, when unnecessary.
Port number: %d
自切生品功能 初始化理
未能打通信端口。
确指令定文件的置或确是否安装了展通信卡。
通信端口在切模式[基板 ID 切]必使用。
如不需要，更改切模式。
端口号: %d
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 219 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea25623 Take over file write-in error
Writing of take over file went wrong.
移交文件写入
移交文件的写入失了。
Ea25624 Take over file reading error
Reading of take over file went wrong.
移交文件入
移交文件的入失了。
Ea25625 Manual Select plan
The following ID information was set up.
ASSY:%s
Surface Information:%s
Program Name:%s
Board Count:%d
Creation time:%s
Do you want to plan it from this information?
品指定切
已置了下列 ID 信息。
ASSY 号 :%s
生面信息 :%s
程序名称 :%s
定生枚数:%d
生成日期 :%s
用信息行生品切?
Ea25626 Auto Plan Change
It changes to an auto plan "No Use."
Please use this mode to choose a plan manually.
However, when it changes into "No Use", it will be in the following states.
- Board Id is deleted altogether.
- Production number of sheets and production schedule number of sheets are reset.
- It cannot return to the state before change.
Is it all right?
自切生品功能的切
将自切生品功能置[不使用]。
如要用手切生品，使用模式。
但，更改[不使用]，将成以下状。
- 将除全部基板 ID。
- 生枚数、定生枚数将初始化。
- 不能原至切前的状。
确行?
Ea25627 Auto Plan Change
It changes to an auto plan "Use."
Please use this mode to perform an auto plan.
Is it all right?
自切生品功能的切
将自切生品功能置[使用]。
如果要使用自切生品功能，模式。
确行?
Ea25628 Auto Plan Change
It is an auto plan "Use."
In this mode, it does not correspond to the plan selection in manual operation.
Please change auto plan use mode into "No Use"
from ID monitor or choose "Yes" to perform plan selection.
However, when it changes into "No Use", it will be in the following states.
- Board Id is deleted altogether.
- Production number of sheets and production schedule number of sheets are reset.
- It cannot return to the state before change.
Do you want to perform plan selection in manual operation?
自切生品功能的切
自切生品功能于[使用]状。
模式下，不能用手切生品。
如要手，从 ID 控屏将自切生品功能的
使用模式更改[不使用]，或[是]。
但，更改[不使用]，将成以下状。
- 将除全部基板 ID。
- 生枚数、定生枚数将初始化。
- 不能原至切前的状。
可以行用手方式切生品?
Ea25629 Auto Plan Change
It is an auto plan "Not Use."
The usual production will be started if auto running is started as it is.
Please change to an auto plan "Use" to perform production
which used the auto plan.
Do you want to change to an auto plan "Use"?
自切生品功能的切
自切生品功能于[不使用]状。
如在状下行自运行，将行通常的生。
若要使用自切生品功能行生，
将自切生品功能置[使用]。
确将自切生品功能置[使用]?
Ea25630 Program list file access failure.
Since other equipment or external PC is using the program list,
it cannot be edited. Please stop editing by corresponding equipment.
Equipment under edit:
不能程序列
其他或外部的 PC 正在使用程序列，所以不能。
在相上中止。
正在的:
Ea25631 Board ID reading error
Reader Index : 1
Status : %s
Reading Result: %s
Reader Index : 2
Status : %s
Reading Result: %s
Please retry or input Board ID manually.
基板 ID 信息取
器号: 1
状 : %s
取果 : %s
器号: 2
状 : %s
取果 : %s
重新行或手入 ID 信息。
Ea25632 Auto Plan Change
It is an auto plan "Use."
In this mode, it does not correspond to the plan selection in manual operation.
Please perform the following procedure to change auto plan mode into "No Use."
1. Reset by taking out all board from inside of machine.
2. Change auto plan use mode into "No Use" from ID Monitor.
自切生品功能的切
自切生品功能于[使用]状。
模式下，不能使用手切生品。
如要将自切生品功能更改[不使用]，
按如下行。
1.将机器内全部基板出，并行位。
2.在 ID 控屏中将自切生品功能的使用模式更改[不使用]。
Ea25633 Auto Plan mode change
Auto plan mode is changed.
Change of Auto plan mode deletes all of ID information,
the production number of sheet, and the production plan number of sheet.
When you start production, please reread production kind information.
When Auto plan mode is "None", please start production in the usual procedure.
切模式的更改
更改切模式。
如果更改切模式，全部 ID 信息、生枚数、定生
枚数将被除。
始生，重新入生品信息。
[不使用自切生品]，按通常的序始生。
Ea25634 Auto Plan start error
In the state where there is no production kind information,
Board was detected at the last process.
Auto plan cannot be started with this.
Since production kind information is reread, please start production.
自切生品功能始
没有生品信息的状下，在前道工序中出了基板。
在此状下无法始自切生品功能。
重新入生品信息后，再始行生。
Ea25635 Production Plan error
Production for schedule number of sheets is not completed.
生枚数
没有达到定生枚数。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 220 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Although production of a stock-in-hand kind cannot be continued
when auto plan mode is changed, do you want to chage auto plan mode?
更改切模式后，不能当前品的生。
需要更改切模式?
Ea25636 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in sub stopper position.
Automatic plan operation can't be continued.
Remove the board of sub stopper position.
无基板 ID 信息
待机位置不存在基板 ID 信息。
在此状下无法用自切生品功能行运行。
取出待机位置的基板。
Ea25637 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in upper buffer conveyor position.
Automatic plan operation can't be continued.
Remove the board of upper buffer conveyor position.
无基板 ID 信息
上冲送位置上不存在基板 ID 信息。
在此状下无法使用自切生品功能行运行。
取出上冲送装置上的基板。
Ea25638 THERE IS NO BOARD ID INFOMATION.
Board ID information doesn't exist in main stopper position.
Automatic plan operation can't be continued.
Remove the board of main stopper position.
无基板 ID 信息
印刷位置不存在基板 ID 信息。
在此状下无法使用自切生品功能行运行。
取出印刷位置上的基板。
Ea25639 Auto plan start error
The error occurred during the automatic plan change.
The current board data differs from the program name
contrasted from production kind information.
Production of as it is present is uncontinuable.
When you resume production, please cope with it as follows.
1.Automatic plan use mode is changed into "No Use."
2.Board data is reread from a Setup screen.
3.Automatic plan use mode is changed into "Use."
4.Automatic operation is resumed and
production kind information is reread.
自切生品功能始
在切自切生品功能中生了。
当前入的基板程序与生品信息所的程序名称不一致。
无法当前的生。
如重新始生，按照如下行。
1.将自切生品功能的使用模式更改[不使用]。
2.在生画面重新入基板程序。
3.将自切生品功能的使用模式更改[使用]。
4.重新始自运行，重新入生品信息。
Ea25640 Auto plan warning
The error occurred during automatic plan operation.
Please cope with it as follows and
check the contents of an error displayed.
-It stands by until all the Board in a machine are conveyed.
-Auto running is stopped.
自切生品警告
使用自切生品功能行运行的程中生了。
按照如下方法之一，确示的内容。
·使机器置于待机状，直至机器内的基板全部出止。
·停止自运行。
Ea25641 NO BOARD DATA
Although automatic reading of a dummy board was performed,
the specified Board data does not exist.
BOARD DATA %s
无基板程序
行了虚基板的自入，但指定的基板程序
没有登在机器中。
基板程序 %s
Ea25642 Auto Plan start error
In the state where there is no production kind information,
Auto plan was started.
Auto plan cannot be started with this.
Since production kind information is reread, please start production.
自切生品功能始
在没有生品信息的状下，始了自运行。
在此状下无法始自切生品功能。
重新入生品信息后，再始生。
Ea25643 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
It is an auto plan "Not Use."
Please change to an auto plan "Use".
条板 ID 取
不能取条板 ID。
原因
自切生品功能于[不使用]状。
将自切生品功能切[使用]。
Ea25644 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
Next ASSY information has already been registered.
Please cancel registered information when you want to
register ASSY information again.
Please reset it when you want to cancel.
条板 ID 取
不能取条板 ID。
原因
已登了下个品信息。
重新登品信息，
将已登品信息取消。
若要取消，先初始化。
Ea25645 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
The error occurred during automatic plan operation.
Please cope with it as follows and
check the contents of an error displayed.
-It stands by until all the Board in a machine are conveyed.
-Automatic operation is stopped.
条板 ID 取
不能取条板 ID。
原因
使用自切生品行运行的程中生了。
按照下列方法之一，确所示的内容。
·置于待机状，直至机器内的基板全部送完止。
·停止自运行。
Ea25646 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
KANBAN ID cannot be read at a present operator level.
Please operate it by the operator to whom the readout
of KANBAN ID is permitted.
条板 ID 取
不能取条板 ID。
原因
当前的操作不能取条板 ID。
由允取条板 ID 的操作者行操作。
Ea25647 KANBAN ID READOUT ERROR
KANBAN ID cannot be read.
Cause
A Board or Board ID information exists in equipment.
Please reset it after removing all Board and Board ID information
in equipment.
条板 ID 取
不能取条板 ID。
原因
内存在基板、或 ID 信息。
将内的基板、或 ID 信息全部除。