YAMAHA 报警资料.pdf - 第148页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 148 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 147 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please consult your distributor for further information. 向制造商咨。
Es00211 Es00211:KG2-58D9 File Close Error
Please consult your distributor for further information.
Es00211:KG2-58D9 文件
向制造商咨。
Es00212 Es00212:APPL CPU Handshake Error
APPL or I/O communication has a trouble.
--- CAUSE ---
Failure in connecting of I/O cables.
Error in the APPL board.
--- COUNTERMEASURE ---
Check the mechanical friction in I/O.
Check the cables of earth.
Power ON again.
Replace APPL-board.
Es00212:APPL CPU 信号交
APPL 或 I/O 通信中有异常。
原因:
·I/O 通信的断，APPL 卡内部的。
策:
·确 I/O 通信的接插件是否脱出·断、
接地是否松懈。
·重新接通源，更 APPL 卡。
Es00213 Es00213:Servo HEX Data Error
Please consult your distributor for further information.
Es00213:Servo HEX 数据
向制造商咨。
Es00214 Es00214:Servo HEX Address Error
Please consult your distributor for further information.
Es00214:Servo HEX 地址
向制造商咨。
Es00215 Es00215:ENB/DIS before D.L.
Please consult your distributor for further information.
Es00215:ENB/DIS before D.L.
向制造商咨。
Es00216 Es00216:KG2-42S7 File Read Error
Please consult your distributor for further information.
Es00216:KG2-42S7 文件入
向制造商咨。
Es00217 Es00217:KG2-42S9 File Write Error
Please consult your distributor for further information.
Es00217:KG2-42S9 文件写入
向制造商咨。
Es00218 Es00218:KG2-42S8 File Write Error
Please consult your distributor for further information.
Es00218:KG2-42S8 文件写入
向制造商咨。
Es00219 Es00219:KG2-42S7 File Write Error
Please consult your distributor for further information.
Es00219:KG2-42S7 文件写入
向制造商咨。
Es00220 Es00220:KG2-58D9 File Write Error
Please consult your distributor for further information.
Es00220:KG2-58D9 文件写入
向制造商咨。
Es00221 Es00221:KG2-42S8 File Read Error
Please consult your distributor for further information.
Es00221:KG2-42S8 文件入
向制造商咨。
Es00222 Es00222:KG2-42S7 File Read Error
Please consult your distributor for further information.
Es00222:KG2-42S7 文件入
向制造商咨。
Es00223 Es00223:KG2-42S7 File Read Error
Please consult your distributor for further information.
Es00223:KG2-42S7 文件入
向制造商咨。
Es00224 Es00224:Servo Card Not Found
--- CAUSE ---
There is no Servo Card detected on the motherboard.
--- COUNTERMEASURE ---
Reset Servo Card.
Change to new Servo Card.
Es00224:伺服卡未安装
向制造商咨。
原因:
·伺服卡没有插入。
策:
·拆下伺服卡再重新安装。
·更伺服卡。
Es00225 Es00225:KG2-58D9 File Read Error
Please consult your distributor for further information.
Es00225:KG2-58D9 文件入
向制造商咨。
Es00226 Es00226:KG2-58D9 File Read Error
Please consult your distributor for further information.
Es00226:KG2-58D9 文件入
向制造商咨。
Es00227 Es00227:BadSRAM/DC srv#1
Please consult your distributor for further information.
Es00227:BadSRAM/DC srv#1
向制造商咨。
Es00228 Es00228:BadSRAM/DC srv#2
Please consult your distributor for further information.
Es00228:BadSRAM/DC srv#2
向制造商咨。
Es00229 Es00229:BadSRAM/AC srv
Please consult your distributor for further information.
Es00229:BadSRAM/AC srv
向制造商咨。
Es00230 Es00230:Servo Card1 Data Write Error
Please consult your distributor for further information.
Es00230:Servo Card1 数据写入
向制造商咨。
Es00231 Es00231:Servo Card2 Data Write Error
Please consult your distributor for further information.
Es00231:Servo Card2 数据写入
向制造商咨。
Es00232 Es00232:Servo Card3 Data Write Error
Please consult your distributor for further information.
Es00232:Servo Card3 数据写入
向制造商咨。
Es00233 Es00233:Servo Card4 Data Write Error
Please consult your distributor for further information.
Es00233:Servo Card4 数据写入
向制造商咨。
Es00234 Es00234:Binary File Over 32KB
Please consult your distributor for further information.
Es00234:Bin.FileOver32KB.
向制造商咨。
Es00235 Es00235:Illegal PLC Function
Please consult your distributor for further information.
Es00235:IllegalPLC Func.
向制造商咨。
Es00236 Es00236:I/O Already Down Loaded
Please consult your distributor for further information.
Es00236:I/O 已完成下
向制造商咨。
Es00237 Es00237:Servo CPU No Answer
Please consult your distributor for further information.
Es00237:司伏 CPU 没有答
向制造商咨。
Es00238 Es00238:KM5-42S8 File Open Error
Please consult your distributor for further information.
Es00238:KM5-42S8 文件打
向制造商咨。
Es00239 Es00239:KM5-42S8 File Close Error
Please consult your distributor for further information.
Es00239:KM5-42S8 文件
向制造商咨。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 148 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Es00240 Es00240:KM5-42S8 File Write Error
Please consult your distributor for further information.
Es00240:KM5-42S8 文件写入
向制造商咨。
Es00241 Es00241:KM5-42S8 File Read Error
Please consult your distributor for further information.
Es00241:KM5-42S8 文件入
向制造商咨。
Es00300 Es00300: Es00300:
向制造商咨。
Es00301 Es00301:File Read Error
Please consult your distributor for further information.
Es00301:文件入
向制造商咨。
Es00302 Es00302:File Seek Error
Please consult your distributor for further information.
Es00302:文件找
向制造商咨。
Es00303 Es00303:File Open Error
Please consult your distributor for further information.
Es00303:文件打
向制造商咨。
Es00304 Es00304:File Write Error
Please consult your distributor for further information.
Es00304: 文件写入
向制造商咨。
Es00305 Es00305:Softlimit Over
--- CAUSE ---
One or more servo axes are out of softlimit.
--- COUNTERMEASURE ---
Move the axis until error message disappears
Es00305:极限溢出
原因:
极限外的地方有伺服的。
策:
移至提示信息消失。
Es00306 Es00306:Watch Cat Error
Please consult your distributor for further information.
Es00306:端口
向制造商咨。
Es00307 Es00307:Invalid Target Coordinates
Please consult your distributor for further information.
Es00307:目坐异常
向制造商咨。
Es00308 Es00308:Interlocked
--- CAUSE ---
Interlocked.
--- COUNTERMEASURE ---
Release interlock of error message.
Es00308:装置状
原因:
置了装置。
策:
解除提示的装置。
Es00309 Es00309:Maintenance Switch is ON
--- CAUSE ---
Current condition is Low speed mode by NJ13 switch.
--- COUNTERMEASURE ---
Change setting of NJ13 switch.
Es00309: ON
由于 NJ13 的，呈低速运行状。
策:
更改 NJ13 的状。
Es00310 Es00310:Vision No Answer
Please consult your distributor for further information.
Es00310:未答
向制造商咨。
Es00311 Es00311:No Such Video Image
Please consult your distributor for further information.
Es00311:没有取得像
向制造商咨。
Es00312 Es00312:No Trigger Pulse
Please consult your distributor for further information.
Es00312:没有触脉冲
向制造商咨。
Es00400 Es00400:C/R BOX FAN STOP
The fan in control box is NG.
--- CAUSE ---
The fan is defective.
The cable between the fan and the mother board is disconnected
or contact-fail.
The fan locks by dust etc.
--- COUNTERMEASURE ---
Check the cable between the fan and the mother board.
Cleaning around the fan.
Replace the fan.
Es00400:C/R BOX FAN STOP
控制箱内的冷却扇已停止了。
--- 原因 ---
冷却扇的异常
扇和主板的接接插件的松落
由埃等所造成的堵塞致扇定
--- 策 ---
确接插件的接状
清扇周
更扇
Es00401 Es00401:C/R AC POWER NG
AC power at control box is NG.
--- CAUSE ---
The trip of circuit-protector, or slack of the terminal
stand screw.
The cable at control box is disconnected or contact-fail.
The mother board is defective.
The power supply stopped for a moment.
--- COUNTERMEASURE ---
Check the circuit-protector.
Check the cable at control box.
Replace mother board.
Es00401:C/R AC POWER NG
供控制箱的 AC100V 异常。
--- 原因 ---
路保器的 OFF、或配接的接板螺松了
控制箱部的接插件的松落
主板的异常
突然停断
--- 策 ---
路保器
确接板、接插件的接状
控制箱部的接插件的松落
更主板
Es00402 Es00402:C/R DC POWER NG
DC power at control box is NG.
--- CAUSE ---
The slack of the terminal stand screw of the switching power supply.
The switching power supply or mother board is defective.
The output voltage adjustment of the switching power supply
is defective.
--- COUNTERMEASURE ---
Check green LED of the switching power supply and the mother board.
Check with tester about the output voltage in terminal stand of
Es00402:C/R DC POWER NG
控制箱内供的 DC 源异常。
--- 原因 ---
DC 源的配接的接板的螺松了
DC 源的异常、主板的异常
DC 源的出整不良
--- 策 ---
确 DC 源的色 LED 和主板的色 LED 的亮灯状
DC 源接板部的出、确的
接板的螺是否松
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 149 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
the switching power supply, and voltage adjustment in volume.
Check the terminal stand screw.
Replace the switching power supply or mother board.
更 DC 源或主板
Es00403 Es00403:C/R TEMP NG
The temperature at control box is too high.
--- CAUSE ---
The temperature around the machine is rising.
The cooling function of the machine is defective.
The cooling function of the control box is defective.
The mother board is defective.
-- COUNTERMEASURE ---
Check the air intake or outlet of the machine.
Check the air intake or outlet of the control box.
Check the terminal stand screw.
Es00403:C/R TEMP NG
控制箱内的温度异常上升。
--- 原因 ---
装置主体周的温度上升
装置主体的冷却功能减弱
控制箱的冷却功能减弱
主板的异常
-- 策 ---
确装置的气口、排气口是否被某物品堵塞了
确装置和控制箱的气口是否因垢而
确接板的螺是否松
Ea11000 No Error 正常束
Ea11090 Check Sum 合
Ea11091 Illegal Chain Code 式
Ea11092 Time Out 超
Ea11093 Illegal Character 字符
Ea11094 Illegal Address 地址
Ea11095 FROM Erase FROM 清除
Ea11100 Illegal Command 指令
Ea11101 Illegal Parameter 参数
Ea11102 Illegal Buf. Memory 像内存指定
Ea11103 ???(#103)
Ea11104 Illegal Fiducial No. 基准号
Ea11105 Illegal View No. 野号
Ea11106 Illegal Hist Step 直方段
Ea11107 Illegal Nozzle No. 吸嘴号
Ea11108 Illegal LinePrm No. 生参数号
Ea11110 Illegal Object No. 象号
Ea11111 Overflow Object Num 象多
Ea11120 Area=0 or Area=?? 面 0 或面不定
Ea11130 Work Area Overflow 工作区溢出
Ea11131 Part Overflow 件溢出
Ea11132 No Part ID 无指定件 ID
Ea11133 Illegal Library Data 信息数据
Ea11134 Library Load Error 信息加
Ea11135 Template Overflow 板溢出
Ea11136 Illegal Template No. 板号
Ea11137 No Template 板未登
Ea11140 Not Available 功能不可行
Ea11145 Illegal Window
Ea11149 Intensity of part is not enough. 吸嘴亮度
Ea11150 Lead Search Error
Failed to find the lead.
引脚出
不能出引脚。
Ea11151 Lead Number Error
Incorrect number of detected leads.
引脚数量
出的引脚数量与置内容不一致。
Ea11152 Lead Pitch Error
The lead pitch is out of tolerance.
引脚距
出的引脚距在公差范外。
Ea11153 Lead Width Error
The lead width is out of tolerance.
引脚度
出的引脚度在公差范外。
Ea11154 Lead Top Search Error
Failed to find the lead tops.
引脚前端出
未能出引脚前端。
Ea11155 Lead Center Error
Failed to detect the component.
引脚中心出
元件的已失。
Ea11156 Lead Number = 0
Incorrect number of detected leads.
引脚数量 0
出的引脚数量和置内容不一致。
Ea11157 Lead Group Center Error
Failed to detect the component.
引脚列的中心出
元件的已失。
Ea11158 Chip Center Error
Failed to detect the component.
芯片中心出
元件的已失。
Ea11159 Bend Detect Error
Failed to detect the component.
引脚弯曲
元件的已失。
Ea11160 Measure Error
Cannot be found.
出
不能出。
Ea11161 Area Error
The area or perimeter value of the detected it is
out of tolerance.
面
不能出已指定面或周的公差范内的。
Ea11162 Shape Error
Failed to detect the specific shape of the defined.
形状
不能出指定形状的。