YAMAHA 报警资料.pdf - 第204页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 204 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 203 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea17500 Line Number mismatch
The line number is different between the selected
file and this program.
Adopt this program's line number - OK?
生序号不一致
所文件的生序号和此程序的生序号不一致。
可以使用此程序的生序号?
Ea17501 File Writing Failure!
Failed to write to the line information file.
文件保存
生信息文件的保存失了。
Ea17502 File Writing Failure!
Failed to write to the nozzle number information file.
文件保存
吸嘴数信息文件的保存失了。
Ea17503 File Writing Failure!
Failed to write to the feeder number information file.
文件保存
送料器个数信息文件的保存已失。
Ea17504 Enter a save file name. 入置保存文件名。
Ea17505 Warning!
Do you want to clear trace information?
作的确
清除跟踪信息。
您确定?
Ea17506 Warning!
Do you wish to stop the executing process?
[Yes] Stop
[No] Continue
作的确
是否中止最化理?
[是] 中止
[否] 不中止
Ea17507 It is impossible to close this application while optimizing.
Please stop the process, then close it.
因正在行最化，所以不能束。
先中断理，然后再束。
Ea17508 Warning!
Do you want proceed and save the current result?
[Yes] Save the current result and stop.
[No] Abort the result and stop immediately.
作的确
完成此最化理循，保存果后，中止?
[是] 保存此基板的中果并中止。
[否] 放弃果，立刻中止。
Ea17509 Warning!
It's not possible to save Board data in this demo version.
警告
因是示范版，所以不能保存基板程序。
Ea17510 Enter a file name to save to. 入文件名。
Ea17511 Maximum number of characters exceeded!
The number of characters of the save Board name
exceeded a limitation (%s characters).
The save Board name is made same as the target Board name.
Target Board Name : %s
文字字数溢出!
保存基板名的字数已超(%s 文字)。
将保存基板名置成行基板名。
行基板名: %s
Ea17512 Delete all optimize result information.
Delete all optimize result information file.
Select [Yes] to continue.
最化果信息文件的除
除最化果信息文件。
若要理，[是]。
Ea17513 Initial value check of Estimate Correction
Please set Estimate Correction of each machine as an initial value (100).
As for Improvement in Estimate accuracy, Estimate Correction is adjusted
in the state of the initial value (100).
推校正初始确
将各个机器的推校正置初始(100)。
推精度的提高是在推校正置初始
(100)的状下行整的。
Ea17514 BOARD DATA ERROR
Mount position is outside moving area.
Component data Name
Axes
基板程序
装位置在作范外。
元件数据 号 名称
名称
Ea17515 File Read Error
Failed to read "Nozzle Priority Setting File".
Normal nozzle priority is set and optimization is excuted.
文件入
吸嘴先度置文件的入已失。
用通常的吸嘴先度的置来行最化。
Ea17516 Failed to delete temp optimizinig data.
Machine
Board
最化数据的除失了。
机器名称
基板名称
Ea17517 Failed to make temp optimizinig data.
Machine
Board
最化数据的生成失了。
机器名称
基板名称
Ea17518 DATA CHECK ERROR
"Part Group Number" is contradicted
between machines.
Machine
程序
在下列机器所属的元件中，"元件号"存在矛盾。
机器名称
Ea17521 WARNING!
"Part Group Number" is contradicted
between machines.
Board Name :
Source Machine :
Source Component : Name
Reference Machine :
Reference Component : Name
警告
下列机器的元件元件号存在矛盾。
基板名称 :
参照自机器名称 :
参照自元件 : 号 名称
参照目的地机器名称 :
参照目的地元件 : 号 名称
Ea17522 WARNING!
"Part Group Number" is contradicted
between machines.
Board Name : %s
Source Machine : %s
Source Component : %s Name : %s
警告
下列机器的元件元件号存在矛盾。
基板名称 : %S
要参照的机器名称 : %S
要参照的元件 : %S 号 名称: %S
参照目的位置机器名称 : %S
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 204 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Reference Machine : %s
Reference Component :%s Name : %s
Do you continue?
参照目的位置元件 : %S 号 名称: %S
行?
Ea18000 Feeder Overflow!
There is not enough feederbarspace in the line to
accommodate all feeders.
送料器溢出
因基板程序的送料器个数比全部机器的送料器安装空多，
所以不能行分配。
Ea18001 Feeder Overflow!
There is not enough feederbar space on those machines
in the line that can handle specific parts.
Machine
Example of specific parts:
- Pick/Mount Action is 'FINE'.
- Dump Way is 'Station'.
- Using Special Nozzle.
etc.
送料器溢出
只能安装在符合条件的装置上的元件所用送料器个数超了
可安装的送料器空。
机器名称
*只能安装在符合条件的装置上的元件例
- 吸附/放作「FINE」
- 弃方法「弃站」
- 使用特殊吸嘴的元件
Ea18002 Feeder Overflow!
There is less feederbar space in the line than is
required for redistribution of the already set parts.
送料器溢出
已分配的元件的再分配所需的送料器个数超了
可安装的送料器空。
Ea18003 Feeder Overflow!
There is not enough feederbar space on the machine to which
parts have been assigned.
送料器溢出
已分配到装置的元件的送料器个数超了装置可安装
的送料器空。
Ea18004 Filling Optimization Error
Initialization of feeder filling information failed.
最化
送料器配置信息的初始化已失。
Ea18005 Feeder Overflow!
There were components which cannot be attached
even if it makes filling placement of the feeder.
Please also take into account the feeder positions used by
static components and fixed Board's.
送料器溢出
已行送料器凑配置，但仍存在不能安装的元件。
修改固定元件、固定基板的置。
Ea18006 Filling Optimization Error
Reset of feeder filling information failed.
凑配置最化
送料器凑配置信息的束理已失。
Ea18007 Filling Optimization Error
There were components which can be located on no table.
Component data Name
凑配置最化
在数个工作台装置上存在哪个工作台都不能配置的元件。
元件数据 号 名称
Ea18100 Tray Overflow!
There is not enough palette space on those machines
in the line that can handle specific parts.
Machine
托 溢出排气
只能在符合条件的装置上配置的元件的料架数
超了可安装的料架数。
机器名称
Ea18101 Tray Overflow!
There is less palette space in the line than is
required for redistribution of the already set palettes.
Machine
托 溢出排气
已配置元件的再分配所必需的料架数超了可安装
的料架数。
机器名称
Ea18102 Tray Optimization Error
Initialization of tray parts auto set information failed.
托 最化
托最化信息的初始化失了。
Ea18103 Tray Optimization Error
There were tray parts which cannot be attached
even if it makes filling placement of the tray stacker.
Please also take into account the feeder positions used by
static components and fixed Board's.
Machine
Component data Name
托 最化
存在无法决定料架数的托元件。
修改固定元件、固定基板的置。
机器名称
元件数据 号 名称
Ea18104 Tray Optimization Error
Reset of tray parts auto set information failed.
托 最化
托最化信息的束理失了。
Ea18500 The requested plan file does not exist.
Please check the file name.
入的送料器位置置文件名不存在。
确文件名。
Ea18501 SETUP OPTIMIZER ERROR
Fine is not found.
送料器位置共同置
未能打文件。
Ea18502 SETUP OPTIMIZER ERROR
Matching of a part name went wrong.
送料器位置共同置
元件名的匹配失了。
Ea18503 SETUP OPTIMIZER ERROR
There are parts that could not be assigned to a machine.
送料器位置共同置
有未分配机器的元件存在。
Ea18504 SETUP OPTIMIZER ERROR
Alternative parts loop includes more than one machine or mounting table.
送料器位置共同置
替代元件跨越了机器或者装工作台。
Ea18505 SETUP OPTIMIZER ERROR
Machine composition differs from the last plan.
送料器位置共同置
机器的构成与上次送料器位置共同置不同。
Ea18506 SETUP OPTIMIZER ERROR
Part information differs from the last plan.
送料器位置共同置
元件信息与上次送料器位置共同置不同。
Ea18507 Feeder which is not displayed has already existed.
If processing is continued as it is, it may become the cause of interference of feeder.
Is processing continued as it is?
已存在送料器，送料器只不没有示。
如果理，可能造成送料器互相干。
理?
Ea18508 Board file is not found.
PATH : %s
BOARD : %s
没找到基板文件
路径 : %s
基板名: %s
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 205 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
TYPE : %s 型 : %s
Ea18509 It is going to update the board under present editing.
Do you want to continue processing as it is?
正要更新正在中的基板。
仍然理?
Ea18510 The invalid set position number was set up.
Do you want to move feeder to un-arranging?
置的安装位置号无效号。
是否将送料器移至未置安装送料器的位置?
Ea18511 BOARD SAVE
Board %1 is changed.
Do you wish to save changes?
基板保存
基板%1 已更改。
保存?
Ea18512 The board data is already opened for editing and now is re-opened.
If you proceed the edit changes will be lost and
the board data will revert to the previously saved
contents.
Proceed?
正在将中基板用基板器。
如果依此行，基板器将启前的内容。
是否行理?
Ea18513 This board is already added.
Board Name : %1
基板已添加。
基板名称 : %1
Ea18514 Failed to add boards to the plan.
Please use less than %d boards.
The present number of boards is: %d
The number of additional schedule boards : %d
基板添加失了。
将行送料器位置置的基板整%d 个基板以内。
目前的送料器位置置基板数: %d 基板
添加的基板数: %d 基板
Ea18515 There are too many boards.
The number of boards which can be treated
with a common plan sheet is up to 100 boards.
The present number of plan boards : %d
基板数多。
可在送料器位置共同置工作表中使用的基板数只能在 100 之内。
目前的送料器位置置基板数：%d 基板
Ea18516 GROUP board creation went wrong. GROUP 基板生成已失。
Ea18517 Parts will exceed the maximum number. 元件将超出最大数。
Ea18518 Part division was ended normally. 元件分割正常束了。
Ea18519 Part division went wrong. 元件分割失了。
Ea18520 There are too many boards or plan group. 基板数或送料器位置置数多。
Ea18521 When you move parts between machines
"Fiducial"
"Badmark"
These parameters become 0.
元件移在机器之，
·局部基准
·局部坏板
的参数 0。
Ea18522 It failed in the output of Plan Load file. 划荷文件的出失了。
Ea18523 It failed in the output of Production Plan file. 生划文件的出失了。
Ea18524 Do you want to save the folder path now selected?
New Folder Path : [%s]
送料器位置置文件的文件路径已更改了。
可以保存?
新文件路径 : [%s]
Ea18525 WARNING
Some of the following Parts can't be use as Common Plan.
So, number that uses the Parts increase.
Because of either of the following reasons.
- Parts can't be moved between machines.
- There is a restriction by the Parts Group Number.
Plan Group :%d
Parts Name :%s
Do you want to continue?
警告
元件的使用数量将增加。
理由:
由于机器元件不能移或受元件号的限制,
使得下列元件的一部分(或全部)不能作送料器共同置的象使用。
置 :%d
元件名 :%s
需要行理?
Ea18526 CREATE GROUP BOARD ERROR
The problem occurred by processing that added the following Board
to the Group Board.
When you allocate the Parts Group Number in Parts of the Group Board again,
Part Group Number used exceeds the max value(99).
Plan Group :%d
Board Name :%s
--- COUNTERMEASURE ---
- Remove the above Board from Plan Group.
- Set the Part Group Number only when necessary.
GROUP 基板的生成
在 GROUP 基板中添加下列基板，
GROUP 基板的元件重新分配号，
号会超最大(99)。
置 :%d
基板名 :%s
解决法∶
·减少置内的基板数。
·只需要的元件置元件号。
Ea18527 CREATE GROUP BOARD ERROR
The error occurred by processing that added the following Board
to the Group Board.
Plan Group :%d
Board Name :%s
--- COUNTERMEASURE ---
Remove the above Board from Plan Group.
GROUP 基板的生成
在 GROUP 基板中添加下列基板，生了。
置 :%d
基板名 :%s
解决法:
从置中除基板。
Ea18528 PARTS GROUP NUMBER ERROR
Alternative Parts are specified for the following Parts,
but two or more Parts Group Numbers are set to Parts in Alternative Loop.
Please set same Parts Group Number to all parts in the Alternative Loop.
Board Name :%s
Parts No. :%d
Parts Name :%s
元件号
下列元件已指定替代元件，
但替代循中的元件的号却置成了数个。
将替代循中的元件全部置相同的号。
基板名称 :%s
元件号 :%d
元件名称 :%s
Ea18529 PARTS GROUP NUMBER ERROR
There is a problem in Parts Group Number of following Board.
元件号
下列基板的号置。