YAMAHA 报警资料.pdf - 第42页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 42 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 41 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Head No.
装号 号
Ea00881 INTERLOCK ERROR
You can't move N axis,
because there is some heads with INDEX nozzle.
不能启 N 。
下列目。
1．吸嘴交站的吸嘴正安装在装上。
2．吸嘴交站的感器状不正常。
Ea00882 INTERLOCK ERROR
You can't move axis,
because digital multi camera lights were up.
Please check below.
1. Are digital multi camera lights up?
2. Are digital multi camera lights sensor good?
因数多相机的照明正在上升，
所以不能移。
下列目。
1．数多相机照明是否在上升
2．数多相机照明的感器状是否正常
Ea00883 INTERLOCK ERROR
You can't move W axis, because the cover
on lower conveyor is open.
因收到了下送装置机盖启的信号，
所以不能移 W 。
Ea00884 ALARM!
The lights of a wafer camera have been turned off,
because they were switched on too long.
If it is necessary, please turn it on again.
警告!
因晶片相机照明的点灯超了定的，
所以了照明。
如有必要，重新打照明。
Ea00887 INTERLOCK ERROR
You can't move X or Y axis,
because some nozzles exist in the shaft cleaning blow units.
因吸嘴吸嘴排气站的吸嘴感器正在感，
所以 X,Y 无法移。
Ea00888 ILLEGAL NOZZLE DOWN ACTION 1
Head down action is abnormal.Following reasons are possible.
- Board fixation is not correct.
- MntHeight is not correct.
- The nozzle shaft is bent.
- The head did not reach the bottom within 1 sec.
- Fatal error occurred in Servo system.
- Fatal error occurred in I/O communication.
TABLE
HEAD
装下降作异常
装无法到达下降端。可能是以下原因所致。
- 基板固定异常
- 装高度异常
- 吸嘴形
- 下降始后 1 秒内没有到达下降端
- 伺服端口异常
- I/O 端口异常
工作台号
Head 号 号
Ea00889 ILLEGAL NOZZLE DOWN ACTION 2
Head down action is abnormal.Following reasons are possible.
- MntHeight is not correct.
- The nozzle shaft is bent.
- Fatal error occurred in Servo system.
- Fatal error occurred in I/O communication.
TABLE
HEAD
装下降作异常
装的下降作异常。可能由下列原因所致。
- 装高度异常
- 吸嘴形
- 伺服端口异常
- I/O 端口异常
工作台号
Head 号 号
Ea00890 ILLEGAL NOZZLE DOWN ACTION 3
Head down action is abnormal.Following reasons are possible.
- MntHeight is not correct.
- The nozzle shaft is bent.
- The head did not reach the blow position within 1 sec.
- Fatal error occurred in Servo system.
- Fatal error occurred in I/O communication.
TABLE
HEAD
装下降作异常
装无法到达排气始高度。可能是由以下原因所致。
- 装高度异常
- 吸嘴形
- 下降始后 1 秒内没有到达排气始高度
- 伺服端口异常
- I/O 端口异常
工作台号
Head 号 号
Ea00891 INTERLOCK ERROR
You can't move X or Y axis,
because there isn't a shaft cleaning blow unit at the bottom.
因吸嘴排气站不在下降端，所以不能移 X、Y 。
Ea00892 Nozzle mismatch error 1
The installation nozzle and the empty situation of the nozzle station are not in
agreement.
Table
Head
Nozzle Type
The nozzle of the head may be equipped with another nozzle.
Please store the nozzle of the head in the nozzle station by hand,
and perform a nozzle change.
It is very dangerous to operate as it is. Is operation stopped?
[YES] Quit [NO] Continue
吸嘴交站不一致 1
安装的吸嘴和吸嘴站的空位不一致。
工作台号 号
Head 号 号
吸嘴型
Head 上的吸嘴可能装成其他吸嘴了。
用手将 Head 上的吸嘴放回吸嘴交站，并行吸嘴交作。
此状下生将非常危，停止操作?
[是] 停止 [否] 始
Ea00893 Nozzle mismatch error 2
The installation nozzle is in the nozzle station.
Table
Head
Nozzle Type
Please perform a nozzle change after confirming that the head
is not equipped with a nozzle.
吸嘴交站不一致 2
安装的吸嘴在吸嘴交站中。
工作台号 号
Head 号 号
吸嘴型
如确吸嘴不在 Head 上，行吸嘴交作。
如吸嘴在 Head 上，吸嘴交站上可能放着其他 Head 的吸嘴。确。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 42 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
When the head is equipped with the nozzle, the nozzle of another head
may be stored in the nozzle station.Please confirm.
It is very dangerous to operate as it is. Is operation stopped?
[YES] Quit [NO] Continue
此状下生将非常危，停止操作?
[是] 停止 [否] 始
Ea00894 Nozzle mismatch error 3
The empty situation of two or more exists in the nozzle station,
and the installation nozzle cannot be discriminated.
Table
Head
Nozzle Type
The nozzle of The nozzle station may be stored in the mistaken place.
Please confirm the installation nozzle of the head,
and store the shortage nozzle in the nozzle station by hand.
It is very dangerous to operate as it is. Is operation stopped?
[YES] Quit [NO] Continue
吸嘴交站不一致 3
吸嘴交站有多个空位存在，不能辨要安装的吸嘴。
工作台号 号
Head 号 号
吸嘴型
可能吸嘴交站的吸嘴放在了其他位置。
确 Head 上安装的吸嘴，并用手方式将吸嘴交站中不足的吸嘴
放入吸嘴交站的空位中。
此状下生将非常危，停止操作?
[是] 停止 [否] 始
Ea00895 Nozzle mismatch error
The compulsion operating was selected.
May I really begin operating?
[YES] Continue
[NO] Quit
吸嘴交站不一致
了制始。
确始操作?
[是] 始
[否] 停止
Ea00896 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check followings:
- Some nozzles are on the blow unit?
- The sensor detects something but nozzles?
- The sensor is broken?
Table A
吸嘴排气装置的吸嘴感器正在感。
下列目。
- 排气装置上是否不存在吸嘴?
- 感器是否被遮盖?
- 感器是否生故障?
工作台号 A
Ea00897 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check followings:
- Some nozzles are on the blow unit?
- The sensor detects something but nozzles?
- The sensor is broken?
Table B
吸嘴排气装置的吸嘴感器正在感。
下列目。
- 排气装置上是否不存在吸嘴?
- 感器是否被遮盖?
- 感器是否生故障?
工作台号 B
Ea00898 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check followings:
- Some nozzles are on the blow unit?
- The sensor detects something but nozzles?
- The sensor is broken?
Table C
吸嘴排气装置的吸嘴感器正在感。
下列目。
- 排气装置上是否存在吸嘴?
- 感器是否被遮盖?
- 感器是否生故障?
工作台号 C
Ea00899 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check followings:
- Some nozzles are on the blow unit?
- The sensor detects something but nozzles?
- The sensor is broken?
- The setting in VmSpec is right?
[Setting]-[Installation Setting]-[Cleanng Blow Unit]
Table D
吸嘴排气装置的吸嘴出感器正在感。
下列目。
- 排气装置上是否存在吸嘴?
- 感器是否被遮盖?
- 感器是否生故障?
- 机器置是否符合机器格?
[机器置]-[工厂置]-[吸嘴清排气装置]
工作台号 D
Ea00901 DEFINED MAXIMUM AMOUNT OF BOARDS
FOR THE UNLOADER IS REACHED:
Set the parameter [Unloader Count Max.], in the
[Board information] menu to 0 to ignore this.
下料机内的基板枚数已达到了所置枚数。
如[基板信息]内的[定下料枚数]置 0，
不行数。
Ea00902 DEFINED PRODUCTION AMOUNT OF BOARDS IS REACHED.
To continue the production, set the
[Board/Schedule] parameter to 0. When switching
the Board data, make sure that there is no Board
on the buffer conveyor.
生枚数已达到定生枚数。
如此基板的生，将生数量更改 0。
切生基板，确冲送上没有基板存在。
Ea00904 Now WARMING UP .....
Press any key to stop WARMING UP.
在正在行暖机运行。
如要停止，按[ESC]。
Ea00905 Stopped according to CONVEY OUT BOARD button.
When switching the Board data, make sure that there
is no Board on the buffer conveyor.
基板装后，按照出指令已停止了送。
切生基板，确冲送上没有
基板存在。
Ea00906 EMERGENCY STOP function is now active.
Or INTERLOCK is active.
急停机状或运行中，
不能切断源。
解除急停机和。
Ea00909 Search for origin failed
due to EMERGENCY SWITCH or SERVO ERROR.
因急停机和伺服等原因，
返回原点失了。
Ea00910 ILLEGAL TRAY DATA DURING RUNNING-1
Meaning: Illegal data during running.
Recovering: Pls. RESET RUNNING.
运行中托数据异常 1
内 容: 运行中数据生了异常。
恢方法: 行初始化理。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 43 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea00914 CYCLE STOP button was executed.
因[装-停机]指令，机器停止了运行。
Ea00915 DEFINED PRODUCTION AMOUNT OF BOARDS IS REACHED.
To continue the production, set the
[Board/Schedule] parameter to 0. When switching
the Board data, make sure that there is no Board
on the buffer conveyor.
生枚数已达到了定生枚数。
如基板的生，将生枚数改 0。
如切生基板，确冲送装置上没有基板存在。
Ea00916 CYCLE STOP button was executed.
因基板装的完成，机器停止了运行。
Ea00917 GROUP CYCLE STOP button was executed.
因吸料的装已完成，机器停止了运行。
Ea00918 ORIGIN ERROR
Search origin failed,
because the result is too much different from
a dual-offset parameter.
返回原点
因所指定的双重位移与数(量果)
的差在置的范外，所以返回原点失了。
Ea00919 INTERLOCK ERROR
The Y-axis is interfering with the wafer camera LCY-axis.
Please move the Y-asis to front side.
主机 Y 与晶片相机 LCY 相干。
将主机 Y 向机器正面一移，避干。
Ea00928 CONFORM DATUM BALL AUTO SET
Datum ball has already been set.
Execute the automatic setting of datum ball?.
基准球重新置的确
基准球信息已置。
是否需要重新置?
Ea00929 DATUM BALL AUTO SET ERROR
The automatic setting of datum ball failed.
Please set it by manual.
基准球自置
基准球的自置失了。
用手方式重新行置。
Ea00930 Nozzle dirt detection error
Although multi-camera recognition was successful,
side view camera recognition was failed.
Since the nozzle may be dirty, please check a nozzle.
If nozzle is dirty please perform nozzle cleaning immediately,
because it cannot keep good mounting condition.
MountData PartsData
Name Comment
Feeder Pos
Pallet Pos
Table/Head
吸嘴垢出
然多相机成功了，但面相机没有出元件。
吸嘴可能有垢，吸嘴。
吸嘴有垢，可能会造成不良装，立刻清吸嘴。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00931 Part standup detection error
Side view camera found part was picked up with standing up.
Please check in following order.
1. Check the pick up position by manual feeding the feeder.
2. Check the nozzle tip was broken or stuffed nozzle hole.
3. Check the pick up position in parts information.
MountData PartsData
Name Comment
Feeder Pos
Pallet Pos
Table/Head
元件立出
面相机中出了元件立异常。
可能由多原因造成，按下列序行确。
1. 用手送料器，确元件是否被送至正确的位置。
2. 目吸嘴前端，确是否堵塞或缺。
3. 确元件信息的吸附位置坐(X,Y)。
4. 确元件信息的吸料高度。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00932 Part thickness error
The part thickness recognized with the side view camera is
out of tolerance.
Please reconfirm Thickness Tolerance in component information.
MountData PartsData
Name Comment
Feeder Pos
Pallet Pos
Table/Head
元件厚度不足
面相机所的元件厚度尺寸在指定公差范外。
在元件信息的面相机中重新确公差。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00933 Side view camera recognition error
Although multi-camera recognition was successful,
side view camera recognition was failed.
MountData PartsDat
Name Comment
Feeder Pos
Pallet Pos
Table/Head
面相机元件
然多相机成功了，但面相机未能出元件。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00934 Multi-camera recognition error
Although side view camera recognition was successful,
multi-camera recognition was failed.
Please check in following order.
1.Check the part size XY.
多相机元件
然面相机成功了，但多相机失了。
确以下目。
1.元件 XY 尺寸。
2.照明和界限。