YAMAHA 报警资料.pdf - 第131页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 131 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 130 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please create the data for feedback or repeal Feedback Function. 生成反辨象的数据或将
反功能置无效。
Ea08585 DATA CHECK ERROR
Mask Standard Position which is specified isn't supported.
According to the conveyer standard side, please set it to
the following Mask Standard Position.
A) For "Front side"
(1) Front
(2) Center
B) For "Rear side"
(1) Center
(2) Rear
程序
不所置的网板制版基准。
按送基准，置下列网板制版基准。
A) 送基准"前"
(1) 前
(2) 中央
B) 送基准"内"
(1) 中央
(2) 内
Ea08586 DATA CHECK ERROR
Distance From Printing Height of Squeegee Detail is
out of range.
Please set the following values.
0
From 0.01 to 10.0(mm/sec)
程序
刮刀置的[离板 自印刷高度的距离]的置在范外。
置下列数。
0，
0.01 至 10.0(mm/sec)。
Ea08587 SQUEEGEE I/O BOARD DATA READ ERROR
Failed to read Loadcell data from Squeegee I/O Board.
刮刀 I/O 端口 数据取
自刮刀 I/O 端口取器参数失了。
Ea08588 SQUEEGEE I/O BOARD DATA READ ERROR
The parameter of Loadcell in machine data is different from
the data of Loadcell in Squeegee I/O Board.
Please readjust the parametor of Loadcell.
The data of Loadcell in Squeegee I/O Board:
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
刮刀 I/O 端口 程序
机器数据的器参数与从刮刀 I/O 端口取的
器参数不一致。
重新整器参数。
从刮刀 I/O 端口取的数:
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
Ea08589 SQUEEGEE I/O BOARD DATACHECK ERROR
The parametor of Loadcell in machine data is different from
the data of Loadcell in Squeegee I/O Board.
Please readjust the parametor of Loadcell.
The data of Loadcell in Squeegee I/O Board:
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
刮刀 I/O 端口 程序
机器数据的器参数与从刮刀 I/O 端口取的
器参数不一致。
重新整器参数。
从刮刀 I/O 端口取的数:
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
Ea08590 BOARD TABLE PRINT HIGHT ERROR
The print action cannot be executed because the board table
is not in the print height.
Please confirm the state of the board table and the board.
Please restart Auto-Running after Reset.
基板工作台印刷高度
因基板工作台没有达到印刷高度，所以不能行印刷作。
确基板工作台和基板的状。
如无异常，位后，重新始自运行。
Ea08591 DATA CHECK ERROR
If PU axis has been selected detach axis,
Board Clamp cannot be used.
程序
离版 PU ，
不能用基板固定固定基板。
Ea08592 DATA CHECK ERROR
Print inspection is specified to work after sizuri.
But all object are specified not to work after sizuri
on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for sizuri
and "Execution Specification Number" of object
data.
数据
然已置印刷后行印刷、
但是在印刷后的行条件的置全部的象文件印刷后不行。
确印刷后的行条件置、
或象数据的条件号。
Ea08593 DATA CHECK ERROR
Print inspection is specified to work for sizuri less
(Filling adjust).
But all object are specified not to work for sizuri less
B on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for sizuri less
and "Execution Specification Number" of object data.
数据
然已"不行印刷(充校正)"置行印刷、
但是在"不行印刷"的行条件上已置
全部象数据"不行印刷"不行。
确"不行印刷"的行条件置或象数据的条件号。
Ea08594 DATA CHECK ERROR
[Real PCB inspection sizuri Less] is set to
[Auto Inspection] in VmSpec.
However, the setting of data is not correct.
Please confirm data.
[SizuriFirstCheck] must be set to [NotUse].
[FillingAdjust(Manual)] must be set to [Use].
数据
然机器已置[不行印刷的生基板]、
但是基板程序的置不正确。
确以下的置。
- "印刷"置"不使用"。
- "充校正(手)"置"使用"。
Ea08599 DATA CHECK ERROR
Cleaning interval should have following relationship.
[Dry Auto] < [Wet Auto] < [Detail Auto] < [Manual]
程序
清隔的置必遵循下列大小系。
[干式自隔] < [湿式自隔] < [自隔] < [手隔]
Ea08600 [Vacuum Check] Confirmation
[Vacuum Check] is specified to [IgnoreErr].
When recognition error for the fiducial mark occurs,
the machine continues printing without fiducial
[像理校正]置警告
[像理校正]的置[忽略]。
即使基准失，也不会行
基准校正，而是施印刷。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 131 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
correction.
Ea08601 "Demo." button is pressed down.
So print pressure feedback is not executed.
"示范印刷"按已按下。
不会行印控制理。
Ea08602 "No Vision" and "Demo." button is pressed down:
- fiducial recognition will not be executed.
- print pressure feedback will not be executed.
"不"、"示范印刷"按已按下。
不会行基准。
不会行印控制理。
Ea08603 Conveyor width changes.
Please be careful.
改送度。
注意。
Ea08604 Remove Board on the conveyor. 取出送上的基板。
Ea08605 Printing action starts.
Please be careful.
始印刷。
注意。
Ea08606 Squeegee head moves.
Please be careful.
将要移刮刀。
注意。
Ea08607 Board table moves.
Please be careful.
将要移基板工作台。
注意。
Ea08608 Please clean the mask manually.
After cleaning please release "EMERGENCY STOP"
and press below button.
清网板。
如已完成清，机盖，
解除急停机状。
Ea08609 Cleaner moves back.
Please be careful.
将要收回清装置。
注意。
Ea08610 Please clean the mask manually. 清网板。
Ea08611 Do you wish to change squeegee direction? 可以改印刷方向?
Ea08612 Cleaning action starts.
Please be careful.
始自清。
注意。
Ea08613 Do you wish to reset auto running?
This operation is not available under this status.
要位自运行?
因不是位状，所以不能行理。
Ea08614 Executing cleaning action... 正在行自清．．．
Ea08615 Rolling cleaner gauze... 正在卷取清卷．．．
Ea08616 Executing print action... 正在印刷．．．
Ea08617 Reset operation... 正在行位理．．．
Ea08618 Board table is moving... 正在移基板工作台．．．
Ea08619 Cleaner is not fixed.
Do you put it back?
清装置没有收回。
是否收回清装置?
Ea08620 Cleaner is moving back. 正在收回清装置．．．
Ea08621 Board is not fixed.
Do you want to fix the Board?
基板没有固定
是否入基板?
Ea08622 Enclosed squeegee head moves up.
Please be careful.
将要上升封型刮刀。
注意。
Ea08623 Enclosed head is moving up... 正在上升封型刮刀．．．
Ea08624 Fiducial recognition starts.
Please be careful.
将要行基准。
注意。
Ea08625 Recognizing Board fiducial... 正在基板基准．．．
Ea08626 Recognizing Mask fiducial... 正在网板基准．．．
Ea08627 Please release "EMERGENCY STOP". 解除急停机状。
Ea08628 Mask is not clamped.
Do you want to clamp the mask?
网板没有固定，是否固定网板?
Ea08629 Mismatch of detected mask size.
Possible causes:
(1) Detected mask has mismatch size specified in Board
data.
(2) Mask positioner pin is not set correctly.
出网板尺寸不一致
可能因下列原因所致。
(1) 指定尺寸的网板没有安装。
(2) 决定网板位置的定位没有插在正确的位置。
Ea08630 Supply Board on entrance of the conveyer. 将基板插入送入口。
Ea08631 Carrying Board in and fixing it... 正在入并固定基板．．．
Ea08632 Releasing Board and carrying it out... 正在松并出基板．．．
Ea08633 Changing conveyor width... 正在改送度．．．
Ea08634 Squeegee is moving... 正在移刮刀．．．
Ea08635 Do you carry Board in and fix it for confirmation? 是否用入并固定基板方法来行确?
Ea08636 Do you supply solder? 是否供膏?
Ea08637 CLEANING INTERVAL TIME
Specified interval time have passed.
清超
已超指定的，始施清。
Ea08638 END OF JOB
Please press "RUN" button to restart auto running.
作完成
按"RUN"按，重新始自运行。
Ea08639 Board table and squeegee head move.
Please be careful.
移基板工作台和刮刀。
注意。
Ea08640 Cleaner is not fixed. 清装置没有收回。
Ea08641 Cleaner is connected with Board table.
Connection is being released.
清装置着。
解除。
Ea08645 Do you wish to carry out the fixed Board? 是否出基板?
Ea08646 Remove Board on the upper buffer conveyor. 取出上冲送上的基板。
Ea08647 Remove Board on the lower buffer conveyor. 取出下冲送上的基板。
Ea08648 Fixing Board... 正在固定基板．．．
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 132 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea08649 Releasing Board... 正在松基板．．．
Ea08650 Insufficient diskspace left.
There is no more HDD-space for saving inspection result.
Data can't be saved any more until more diskspace is
made available:
1.(Archive and) delete old inspection results.
2.Select another drive to save data to.
磁空不足。
保存果的磁的空容量不足。
如依旧，无法保存数据。
按以下方法确保磁空。
1.除去的果文件。
2.更保存器。
Ea08651 Drive not ready.
The drive to which an inspection result must be saved
is not ready. Possible causes are:
1.A floppy disk is not inserted.
2.A network is not connected.
3.No access right for writing data.
没有准器
保存果的器没有准。
可能因下列原因所致，确。
1．磁没有插入器。
2．网没有接。
3．置禁止写入。
Ea08659 Print Inspection starts.
Please be careful.
将要始印刷。
注意。
Ea08660 Executing print inspection action... 正在行印刷．．．
Ea08661 <<< WARNING >>>
If the enclosed squeegee head attaches on the mask and
is filled by solder, please press "CANCEL" button.
In this case please use "SHAKE OFF" button to move
the squeegee head up.
If you want to enforce it, press "OK" button.
封型刮刀上升警告
封型刮刀接触网板，充填膏，
按"取消"按。
此，用"振停止"按使刮刀上升。
只有在制行，才按"OK"。
Ea08663 <<< WARNING >>>
Current angle of Board table is not good for teaching.
Position teaching has failed.
Do you want to adjust the angle?
示教警告
基板工作台的角度，不适合示教作。
示教无效。
是否更改基板工作台的角度?
Ea08664 Do you wish to carry Board in and fix it? 是否入并固定基板?
Ea08666 Executing rolling action... 正在行膏拌．．．
Ea08667 Do you execute filling solder of Enclosed Head?
Please execute this operation, when solder is completely empty
in Enclosed Head.
It is not necessary to execute this operation for supplying
solder because of solder amount error.
行膏充填?
此操作只有在封型刮刀内完全没有膏才可行。
封型刮刀已有膏、因膏余量而充膏，
没有必要行此操作。
Ea08668 Executing filling solder... 正在充填膏．．．
Ea08669 Please supply solder.
Enclosed Head is running out of solder.
增加膏。
封型刮刀的膏不足。
Ea08671 Executing mask inspection action... 正在行网板．．．
Ea08672 Executing mask measurement action... 正在定网板．．．
Ea08673 Overwrite the result on inspection data?
The result of mask measurement is overwritten on inspection data.
But Board data is not saved.
If you want to save the result, Please save Board data.
是否将网板定果覆盖保存在数据上?
网板定果将覆盖保存在数据的外形
面比率上，但基板程序并不会保存。
如需保存此次的网板定果，保存基板
程序。
Ea08674 "Mask Offset" parameter will change
If you change "Board Distortion" parameter, "Mask Offset"
parameter will change to keep print position.
更新目偏移量。
更新基板歪斜校正参数，必同
更新目偏移量。与基板歪斜校正
参数的化量相当的目偏移量也
随之更新。
Ea08685 SIZURI DEMAND
%s
You have to carry out sizuri,
before going into automatic operation.
Is sizuri performed?
要求印刷
%s
自运行前、需要行印刷。
行印刷?
Ea08686 SIZURI DEMAND
%s
Before going into automatic operation,
you have to carry out sizuri.
When the board is on a conveyor, please remove it.
Is sizuri performed?
要求印刷
%s
自运行前、需要行印刷。
如果送上存在基板、清除基板。
行印刷?
Ea08688 SIZURI INTERVAL OVER
Specified interval time have passed, since the last PCB
was printed.
Is sizuri performed?
印刷要求已
前次的基板印刷后、指定的已。
行印刷?
Ea08689 SOLDER ABANDONMENT WARNING
Specified interval time have passed, since the last PCB
was printed.
Please discard solder.
膏弃警告
从上次基板的印刷始，指定的已。
弃膏。
Ea08690 Do you wish to execute Feedback Printing function?
Please press "RUN" button to restart auto running after
selection.
是否行多重印刷反?
某后，按"RUN"按，再次启自运行。
Ea08691 Do you wish to execute Feedback Cleaning function?
Please press "RUN" button to restart auto running after
是否行清反?
某后，按"RUN"按，再次启自运行。