YAMAHA 报警资料.pdf - 第236页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 236 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 235 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ exit position ]
可能是因下列原因所致，采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[出口位置]
Ea29224 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the exit position to the next machine
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ next machine ]
冲送装置送超
下列基板生了送。
从出口位置 向 下位机 送的基板
可能是因下列原因所致，采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[下位机]
Ea29225 BUFFER CONVEYOR TRANSFER RECOVERY
Operation of the buffer conveyor is recovered.
Do you take out the Board of the transfer error by hand,
and stop the transfer?
[YES] Take out the Board of the transfer error by hand,
and the transfer is stopped.
[NO] Without taking out a board,
the transfer is restarted as it is.
冲送装置恢送
恢冲送装置的送。
是否用手取出生送的基板，并中断送?
[是] 取出基板，并中断送。
[否] 不取出基板，在此状下始送。
Ea29230 Ext. tray changer Door switch open error
Failed to servo-on because the door switch is 'open'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
外部托交器 柜打
因托的柜在""位置，所以无法启伺服。
了恢伺服，有必要将托的柜定。
将柜置""。
确柜定后，再按一次'READY'按。
Ea29231 Ext. tray changer Magazine clamp error
Failed to servo-on because the magazine is not set correctly.
There is a necessity to lock a door of a tray to reactivate a servo.
Please lock the magazine clamp and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
外部托交器 收柜固
因托的收柜固定松了，所以无法启伺服。
了恢伺服，有必要将托的柜定。
将收柜固定，并将柜置""。
确柜定后，再按一次'READY'按。
Ea29232 Ext. tray changer Door close error
Failed to servo-on because the door was closed with the door switch 'close'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'open', and turn it 'close' again.
And press the 'READY' button again after checking the door lock.
外部托交器 柜
因在托的柜""位置的状下了柜，
所以无法启伺服。
了恢伺服，有必要将托的柜定。
先将柜置""，然后置""。
确柜定后，再按一次'READY'按。
Ea29233 Auto tray changer Door switch open error
Failed to servo-on because the door switch is 'open'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托交器 柜打
因托的柜在""位置，所以无法启伺服。
了恢伺服，有必要将托的柜定。
将柜置""。
确柜定后，再按一次'READY'按。
Ea29234 Auto tray changer Magazine clamp error
Failed to servo-on because the magazine is not set correctly.
There is a necessity to lock a door of a tray to reactivate a servo.
Please lock the magazine clamp and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托交器 收柜固
因托的收柜固定松了，所以无法启伺服。
了恢伺服，有必要将托的柜定。
将收柜固定，并将柜置""。
确柜定后，再按一次'READY'按。
Ea29235 Auto tray changer Door close error
Failed to servo-on because the door was closed with the door switch 'close'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'open', and turn it 'close' again.
And press the 'READY' button again after checking the door lock.
自托交器 柜
因在托的柜""位置的状下了柜，
所以无法启伺服。
了恢伺服，有必要将托的柜定。
先将柜置""，然后置""。
确柜定后，再按一次'READY'按。
Ea29236 Auto tray changer Rack protrude error
Failed to servo-on because the magazine is protruded to the door direction.
There is a necessity to lock a door of a tray to reactivate a servo.
Please set the magazine correctly and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托交器 料箱出
因料箱向柜，所以无法启伺服。
了恢伺服，有必要将托的柜定。
将收柜安装好，并将柜置""。
确柜定后，再按一次'READY'按。
Ea29237 Auto Tray Crash Warning
There is danger of pallet crash in this state
because returning pallet is failed.
Please be sure to do the following operation.
1. Confirm whether there is no pallet on the pallet stage.
2. Remove by the hand when a pallet exists on the pallet stage.
自托碰撞警告
料架退回失。
如运行，料架有碰撞的危。
必按以下位。
1. 确料架是否从收柜出。
2. 如有料架出，用手推回收柜。
Ea29238 Auto Tray Servo-On Confirmation
Is not there a pallet on the pallet stage?
If there is not pallet on the pallet stage
and there is not danger of pallet crash,
自托伺服 ON 确
料架台上留有料架?
如确定料架台上没有料架且不会有碰撞的危，
按[是]。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 236 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
please push [YES] button.
[YES] Restart by pushing the 'ready' button again.
[NO] Cancel.
[是] 按'READY'按,重新始运行。
[否] 取消。
Ea30200 Convert Auto Wafer Map
Completed successfully.
晶片自
已正常束。
Ea30201 Convert Auto Wafer Map Failed
Undefined error.
晶片自失
生了未定的。
Ea30202 Convert Auto Wafer Map Failed
Cannot open read file.
晶片自失
无法打要取的文件。
Ea30203 Convert Auto Wafer Map Failed
Cannot open write file.
晶片自失
无法打要写入的文件。
Ea30204 Convert Auto Wafer Map Failed
No rank in read file.
晶片自失
要入的文件没有接。
Ea30205 Convert Auto Wafer Map Failed
Canceled.
晶片自失
已止。
Ea30206 Convert Auto Wafer Map Failed
Wafer size is overflow.
晶片自失
超出了最大的晶片尺寸。
Ea30207 Convert Auto Wafer Map Failed
Number of rank kind is overflow.
晶片自失
超出了最大等数。
Ea30208 Convert Auto Wafer Map Failed
Illegal delimiter.
晶片自失
分隔符的位置非法。
Ea30209 Convert Auto Wafer Map Failed
Rank is non-converted.
晶片自失
存在无法的等。
Ea30210 Convert Auto Wafer Map Failed
Line of no rank in read file.
晶片自失
要入的文件中存在没有等的行。
Ea30211 Convert Auto Wafer Map Failed
Cannot read font file.
晶片自失
无法入文件。
Ea30212 Convert Auto Wafer Map Failed
Cannot write font file.
晶片自失
无法写入文件。
Ea30213 Convert Auto Wafer Map Failed
Cannot read option file.
晶片自失
无法入文件。
Ea30214 Convert Auto Wafer Map Failed
Cannot write option file.
晶片自失
无法写入文件。
Ea30215 Convert Auto Wafer Map Failed
Cannot read source file.
晶片自失
无法入要的文件。
Ea30216 Convert Auto Wafer Map Failed
Cannot write destination file.
晶片自失
无法写入目的位置的文件。
Ea30297 Cannot Run Wafer Map Converter
According to the following reasons, wafer map converter could not be run.
- Reading "WaferMapConverter.ini" file was failed.
- The source folder path set in the file does not exist.
- The source file corresponds to the Wafer Map ID is not found.
晶片器无法启
可能是因下列原因，致晶片器无法启。
- "WaferMapConverter.ini"的入失了。
- 所置的要的文件路径不存在。
- 无法找到与晶片 ID 相的要的文件。
Ea30298 Failed To Run Wafer Map Converter
Failed to create process of Wafer Map Converter.
晶片器的启失了
程的启失了。
Ea30299 Retry To Convert Auto Wafer Map
Is it converted again?
(However, even if it succeeds in retrying,
when the time-out has been occured to the machine,
it is necessary to restart to run again on the machine.)
晶片自重新行
重新行?
(注意，即使重新行成功了，
如生了超，
必在重新启运行。)
Ea30301 Matching Condition Data File Write Error
It failed to write the Matching Condition Data file.
Please confirm followings before restart.
1. Please confirm the connection with Management PC or Server PC.
2. Please confirm file path.
[Machine]-[Option Setting]-[Detail Setting]
-[Matching Condition File Path]
位条件数据写入
位条件数据的文件写入失了。
1. 确管理 PC 或服器的接状。
2. 确文件路径的置。
[机器置]-[置]-[置]
-[位条件数据文件的路径]
Ea30304 Take over File Write Error
It failed to write the take over file.
Please confirm followings before restart.
1. Check the connection with Server PC.
2. Check the following specification about file path.
[Machine]-[Option Setting]-[Detail Setting]-[Common File Path]
移交文件写入
移交文件的写入失了。
确以下内容后重新始运行。
1. 确服器的接状。
2. 确文件路径的置。
[机器置]-[置]-[置]-[通用文件路径]
Ea30305 Remove Board
The board was detected in the exit position,
but the matching condition data file is not created.
When it is not created,
3A process control is not operated correctly.
Measure :
1. Please remove the board in the exit position.
2. Please start auto-running again.
取出基板。
已在出口位置出了基板，
但却未建当前的位条件数据文件。
如没有建位条件数据文件，
3A 校正功能将无法正常运行。
解决方法:
1. 取出出口位置的基板。
2. 重新始运行。
Ea30311 Remove Board
Matching Condition Data was changed while all boards have not carried out.
取出基板。
在印刷基板没有全部出的状下就更改了位
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 237 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
The board detected at the following position was printed under the different
Matching Condition from previous one.
3A Correction does not work correctly when carried by force.
Please remove the board, and put the board into next machine.
条件数据。
在以下位置所出的基板因更改前的位条件数据
已施了印刷，所以如制出基板，无法正确
行 3A 校正。
取出基板并放入下位机器。
Ea30312 Matching Condition Data Change
The Matching Condition Data will be changed.
Please restart auto-running according to the following procedure.
Procedure
1. Watching and wait until all boards on the mounters on which 3A correction is
effective have been finished mounting and all of them have been carried out of
the lowest mounter with 3A correction.
2. Change board data on mounters with 3A Correction for the next production.
Even if borad data have already changed to the target one, please read the borad
again after changing Maching Condition.
3. Restart auto-running.
切位条件数据
切位条件数据。
按以下重新始运行。
1. 确生内行 3A 校正的片机上的所有基板都已
完成了装，且所有基板都已出了最末尾的片机。
2. 将生内行 3A 校正的片机的生基板程序切
接下来要生的基板程序。即使已入了象基板
程序，在切了位条件数据后也必重新入基板程序。
3. 始印刷机的运行。
Ea30313 Matching Condition Data File Write Error
It failed to write the Matching Condition Data file.
Please confirm followings before restart.
1. Check the connection with Management PC or Server PC.
2. Check the following specification about file path.
[Machine]-[Option Setting]-[Detail Setting]-[Common File Path]
位条件数据写入
位条件数据的文件写入失了。
确以下内容后重新始运行。
1. 确管理 PC 或服器的接状。
2. 确文件路径的置。
[机器置]-[置]-[置]-[通用文件路径]