YAMAHA 报警资料.pdf - 第130页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 130 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 129 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Light unit level of view data hasn't been set up.
Mask Inspection View Data
野数据的照明未置。
网板野数据 号
Ea08572 DATA CHECK ERROR
Mask inspection function is specified to work.
But all parameter of inspection execution for following
conditions.
(1) After Dry Auto Cleaning
(2) After Wet Auto Cleaning
(3) After Manual Auto Cleaning
程序
然已指定使用网板，但以下所有条件
的网板都置了"不使用"
(1) "干式自清后"
(2) "湿式自清后"
(3) "手清后"
Ea08573 DATA CHECK ERROR
Mask inspection is specified to work after dry auto
cleaning.
But all object are specified not to work after dry auto
cleaning on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for dry
cleaning and "Execution Specification Number" of object
data.
程序
然已置干式自清后行网板，
但是在干式自清后的行条件置
中所有的象数据都置了干式自清后
不行网板。
确干式自清后的行条件的置
和条件号。
Ea08574 DATA CHECK ERROR
Mask inspection is specified to work after wet auto
cleaning.
But all object are specified not to work after wet auto
cleaning on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for wet
cleaning and "Execution Specification Number" of object
data.
程序
然已置湿式自清后行网板，
但是在湿式自清后的行条件置
中所有的象数据都置了湿式自清
后不行网板。
确湿式自清后的行条件的置
和条件号。
Ea08575 DATA CHECK ERROR
Mask inspection is specified to work after manual
cleaning.
But all object are specified not to work after manual
cleaning on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for manual
cleaning and "Execution Specification Number" of object
data.
程序
然已置手清后行网板，
但是在手清后的行条件置
中所有象数据都置了手清后
不行网板。
确手清后的行条件的置
和条件号。
Ea08576 DATA CHECK ERROR
Local fiducial is specified to work but Board fiducial
is specified not to work.
Local fiducial function requires execution of Board fiducial.
程序
然置使用局部基准，但是基板基准
呈不使用状。
使用局部基准，必使用基板基准。
Ea08577 DATA CHECK ERROR
Board table position XYR during local fiducial
recognition is out of Soft Limit.
程序
局部基准的工作台位置 XYR 在极限外。
Ea08578 DATA CHECK ERROR
Squeeze stroke in print action is not correct.
Please check "Rolling Stroke", "Over Stroke",
"F. Start Offset", "B. Start Offset".
程序
刮刀的印刷作冲程异常。
确"刮刀助跑距离"、"刮刀滑跑距离"、"去程始偏移量"、
"返程始偏移量"的置。
Ea08579 DATA CHECK ERROR
"Fiducial Position" is specified to "Board&Mask Common".
But the parameters in fiducial setting are different between Board
and Mask.
Please check the following parameters.
(1) Coordinates of Fiducial Position
(2) Fiducial Type
(3) Datum Position
程序
基准位置置"基板&网板共同指定"，
但在基板基准和网板基准以下的置不同。
(1) 基准位置坐
(2) 基准型
(3) 准位置
Ea08580 DATA CHECK ERROR
When production starts under specified detail cleaning data,
the cleaner blower motor may overheat.
Working duty of blower motor = Percent
Please change followings.
(1) Increase "Auto Interval".
(2) Decrease "Auto Repeat".
(3) Increase "Dry Auto Speed".
(4) Increase "Wet Auto Speed".
程序
所置的清的使用方法，可能会致
清装置扇达的温度上升超出容范。
用如下方法更改置。
(1) 增加"自隔"。
(2) 减少"自反"。
(3) 加速"干式自速度"。
(4) 加速"湿式自速度"。
Ea08581 DATA CHECK ERROR
Squeegee speed for Feedback Print is out of range.
Please specify correct speed as follows
Double Squeegee : 1 to 200[mm/sec]
Enclosed Head : 1 to 100[mm/sec]
程序
多重印刷反用刮刀速度范之外。
置如下状。
双刮刀 : 1 to 200[mm/sec]
封型刮刀 : 1 to 100[mm/sec]
Ea08582 DATA CHECK ERROR
Print pressure for Feedback Print is out of range.
Please specify correct pressure from 0.01 to 200[N].
程序
多重印刷反用印置范之外。
置在 0.01 至 200[N]之。
Ea08584 DATA CHECK ERROR
Printing or Cleaning Feedback is specified to "Exec".
But the data for feedback does not exist.
程序
然多重印刷、清反功能有效，
但反辨象的数据不存在。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 130 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please create the data for feedback or repeal Feedback Function. 生成反辨象的数据或将
反功能置无效。
Ea08585 DATA CHECK ERROR
Mask Standard Position which is specified isn't supported.
According to the conveyer standard side, please set it to
the following Mask Standard Position.
A) For "Front side"
(1) Front
(2) Center
B) For "Rear side"
(1) Center
(2) Rear
程序
不所置的网板制版基准。
按送基准，置下列网板制版基准。
A) 送基准"前"
(1) 前
(2) 中央
B) 送基准"内"
(1) 中央
(2) 内
Ea08586 DATA CHECK ERROR
Distance From Printing Height of Squeegee Detail is
out of range.
Please set the following values.
0
From 0.01 to 10.0(mm/sec)
程序
刮刀置的[离板 自印刷高度的距离]的置在范外。
置下列数。
0，
0.01 至 10.0(mm/sec)。
Ea08587 SQUEEGEE I/O BOARD DATA READ ERROR
Failed to read Loadcell data from Squeegee I/O Board.
刮刀 I/O 端口 数据取
自刮刀 I/O 端口取器参数失了。
Ea08588 SQUEEGEE I/O BOARD DATA READ ERROR
The parameter of Loadcell in machine data is different from
the data of Loadcell in Squeegee I/O Board.
Please readjust the parametor of Loadcell.
The data of Loadcell in Squeegee I/O Board:
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
刮刀 I/O 端口 程序
机器数据的器参数与从刮刀 I/O 端口取的
器参数不一致。
重新整器参数。
从刮刀 I/O 端口取的数:
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
Ea08589 SQUEEGEE I/O BOARD DATACHECK ERROR
The parametor of Loadcell in machine data is different from
the data of Loadcell in Squeegee I/O Board.
Please readjust the parametor of Loadcell.
The data of Loadcell in Squeegee I/O Board:
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
%s
Zero Lv.[%6.1f] Gain+[%6.1f] Gain-[%6.1f]
刮刀 I/O 端口 程序
机器数据的器参数与从刮刀 I/O 端口取的
器参数不一致。
重新整器参数。
从刮刀 I/O 端口取的数:
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
%s
自身重量取消 Lv[%6.1f] 增益+[%6.1f] 增益-[%6.1f]
Ea08590 BOARD TABLE PRINT HIGHT ERROR
The print action cannot be executed because the board table
is not in the print height.
Please confirm the state of the board table and the board.
Please restart Auto-Running after Reset.
基板工作台印刷高度
因基板工作台没有达到印刷高度，所以不能行印刷作。
确基板工作台和基板的状。
如无异常，位后，重新始自运行。
Ea08591 DATA CHECK ERROR
If PU axis has been selected detach axis,
Board Clamp cannot be used.
程序
离版 PU ，
不能用基板固定固定基板。
Ea08592 DATA CHECK ERROR
Print inspection is specified to work after sizuri.
But all object are specified not to work after sizuri
on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for sizuri
and "Execution Specification Number" of object
data.
数据
然已置印刷后行印刷、
但是在印刷后的行条件的置全部的象文件印刷后不行。
确印刷后的行条件置、
或象数据的条件号。
Ea08593 DATA CHECK ERROR
Print inspection is specified to work for sizuri less
(Filling adjust).
But all object are specified not to work for sizuri less
B on current "Inspection Execution Specification".
Check "Inspection Execution Specification" for sizuri less
and "Execution Specification Number" of object data.
数据
然已"不行印刷(充校正)"置行印刷、
但是在"不行印刷"的行条件上已置
全部象数据"不行印刷"不行。
确"不行印刷"的行条件置或象数据的条件号。
Ea08594 DATA CHECK ERROR
[Real PCB inspection sizuri Less] is set to
[Auto Inspection] in VmSpec.
However, the setting of data is not correct.
Please confirm data.
[SizuriFirstCheck] must be set to [NotUse].
[FillingAdjust(Manual)] must be set to [Use].
数据
然机器已置[不行印刷的生基板]、
但是基板程序的置不正确。
确以下的置。
- "印刷"置"不使用"。
- "充校正(手)"置"使用"。
Ea08599 DATA CHECK ERROR
Cleaning interval should have following relationship.
[Dry Auto] < [Wet Auto] < [Detail Auto] < [Manual]
程序
清隔的置必遵循下列大小系。
[干式自隔] < [湿式自隔] < [自隔] < [手隔]
Ea08600 [Vacuum Check] Confirmation
[Vacuum Check] is specified to [IgnoreErr].
When recognition error for the fiducial mark occurs,
the machine continues printing without fiducial
[像理校正]置警告
[像理校正]的置[忽略]。
即使基准失，也不会行
基准校正，而是施印刷。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 131 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
correction.
Ea08601 "Demo." button is pressed down.
So print pressure feedback is not executed.
"示范印刷"按已按下。
不会行印控制理。
Ea08602 "No Vision" and "Demo." button is pressed down:
- fiducial recognition will not be executed.
- print pressure feedback will not be executed.
"不"、"示范印刷"按已按下。
不会行基准。
不会行印控制理。
Ea08603 Conveyor width changes.
Please be careful.
改送度。
注意。
Ea08604 Remove Board on the conveyor. 取出送上的基板。
Ea08605 Printing action starts.
Please be careful.
始印刷。
注意。
Ea08606 Squeegee head moves.
Please be careful.
将要移刮刀。
注意。
Ea08607 Board table moves.
Please be careful.
将要移基板工作台。
注意。
Ea08608 Please clean the mask manually.
After cleaning please release "EMERGENCY STOP"
and press below button.
清网板。
如已完成清，机盖，
解除急停机状。
Ea08609 Cleaner moves back.
Please be careful.
将要收回清装置。
注意。
Ea08610 Please clean the mask manually. 清网板。
Ea08611 Do you wish to change squeegee direction? 可以改印刷方向?
Ea08612 Cleaning action starts.
Please be careful.
始自清。
注意。
Ea08613 Do you wish to reset auto running?
This operation is not available under this status.
要位自运行?
因不是位状，所以不能行理。
Ea08614 Executing cleaning action... 正在行自清．．．
Ea08615 Rolling cleaner gauze... 正在卷取清卷．．．
Ea08616 Executing print action... 正在印刷．．．
Ea08617 Reset operation... 正在行位理．．．
Ea08618 Board table is moving... 正在移基板工作台．．．
Ea08619 Cleaner is not fixed.
Do you put it back?
清装置没有收回。
是否收回清装置?
Ea08620 Cleaner is moving back. 正在收回清装置．．．
Ea08621 Board is not fixed.
Do you want to fix the Board?
基板没有固定
是否入基板?
Ea08622 Enclosed squeegee head moves up.
Please be careful.
将要上升封型刮刀。
注意。
Ea08623 Enclosed head is moving up... 正在上升封型刮刀．．．
Ea08624 Fiducial recognition starts.
Please be careful.
将要行基准。
注意。
Ea08625 Recognizing Board fiducial... 正在基板基准．．．
Ea08626 Recognizing Mask fiducial... 正在网板基准．．．
Ea08627 Please release "EMERGENCY STOP". 解除急停机状。
Ea08628 Mask is not clamped.
Do you want to clamp the mask?
网板没有固定，是否固定网板?
Ea08629 Mismatch of detected mask size.
Possible causes:
(1) Detected mask has mismatch size specified in Board
data.
(2) Mask positioner pin is not set correctly.
出网板尺寸不一致
可能因下列原因所致。
(1) 指定尺寸的网板没有安装。
(2) 决定网板位置的定位没有插在正确的位置。
Ea08630 Supply Board on entrance of the conveyer. 将基板插入送入口。
Ea08631 Carrying Board in and fixing it... 正在入并固定基板．．．
Ea08632 Releasing Board and carrying it out... 正在松并出基板．．．
Ea08633 Changing conveyor width... 正在改送度．．．
Ea08634 Squeegee is moving... 正在移刮刀．．．
Ea08635 Do you carry Board in and fix it for confirmation? 是否用入并固定基板方法来行确?
Ea08636 Do you supply solder? 是否供膏?
Ea08637 CLEANING INTERVAL TIME
Specified interval time have passed.
清超
已超指定的，始施清。
Ea08638 END OF JOB
Please press "RUN" button to restart auto running.
作完成
按"RUN"按，重新始自运行。
Ea08639 Board table and squeegee head move.
Please be careful.
移基板工作台和刮刀。
注意。
Ea08640 Cleaner is not fixed. 清装置没有收回。
Ea08641 Cleaner is connected with Board table.
Connection is being released.
清装置着。
解除。
Ea08645 Do you wish to carry out the fixed Board? 是否出基板?
Ea08646 Remove Board on the upper buffer conveyor. 取出上冲送上的基板。
Ea08647 Remove Board on the lower buffer conveyor. 取出下冲送上的基板。
Ea08648 Fixing Board... 正在固定基板．．．