YAMAHA 报警资料.pdf - 第173页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 173 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 172 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
只需点󲢺画面的[OK]按󳆃，按[始]按󳆃，
便会取消元件󲨉装状的󲳞中󲢅号，重新始󲨉装。
Ea12686 <<WARNING>> Auto-running with data save function
The data save function for analysis while auto-running is ON.
There is a possibility that tact time expands more than a usual
auto-running.
Moreover, there is a possibility that the disk volume is running short.
Please turn it OFF in software setting when unnecessary.
<<警告>>数据保存功能的自运行
自运行中的分析用数据保存功能于有效状。
󱮼󱯂运行，可能会致与通常自运行相比速度降低的󱂅象。
另外，󳉔󰋋󳋉运行，可能会使数据保存位置的磁󱎭容量受到抑。
如不使用󲢺功能，󲣌按用󲱄件󲢓置按󳆃，将󲢺功能󳋂(OFF)。
Ea12687 SERVICE MODE
Service key is activated. Machine works in the service mode.
Front
Rear
The machine works as follows during the service mode.
- The safety cover can be opened in the state of servo ON.
- axis speed under 10%%.
- Disable communication by RS232C and Ethernet
󱯉模式
󱯉已打(ON)，机器以󱯉模式󲲰行作
前
后
󱯉模式下，可以󲲰行下列作。
·在自停机呈打状(ON)󰋋，可以在伺服 ON 状下打安全盖。
·󲱉速度 10%%以下。
·不能以 RS232C 和以太网󲲰行通信󲲳接。
Ea12688 SERVICE MODE ERROR
The ACTIVE button on a side different from the service key
that had been turned on now was pressed.
The service mode inside can operate only the operation panel
on the side to which the service key is turning on.
󱯉模式󳇮󲣄
当前已打的󱯉的相反一的 ACTIVE 按󳆃呈按下状。
在󱯉模式下，只有󱯉已打一的操作面板才可以操作。
Ea12689 Media are write-protected.
Cause:
Write-protection is applied to media.
Measure:
Please cancel write-protection of media.
媒体禁止写入状
原因:
媒体呈写保状。
措施:
󲣌解除媒体的写保状。
Ea12690 Media are not formatted.
Cause:
The media is using the format form that cannot support.
Measure:
Please perform a exchange for formatted media.
媒体没有格式化
原因:
您所使用的媒体的格式不适用本机。
措施:
󲣌󲲰行格式化或更󰀷成已格式化的媒体。
Ea12691 Failed to access to the "FEEDER ID LOG" file.
%s
To update information for the file on the server, was failed.
There are some possibility of Network Impediment.
Please make sure the condition for above.
Production can be continued with the following condition.
1. The function "ID Log Management" should be set to "Disable"
in Application Setup.
2. Count for Feeder Driven, Error, etc. are not totaled during
this condition is kept.
送料器 ID 履文件存取󳇮󲣄
%s
不能更新保存在服器中的各 ID 履信息。
可能生了网󱮱障碍。
网󱮱障碍排除之前，如要󱮼󱯂生，可以通󲲜用󲱄件󲢓置
将 ID 履管理󲢓置「无效」即可。
但，󲢓置「无效」期󳋉，不能合󲡶送料次数和吸料出󳇮次数等󳕎目。
Ea12692 Failed to access to the "FEEDER ID LOG" file.
%s
To update information for the file on the external storage, was
failed. There are some possibility of Device Impediment.
Production can be continued with the following condition.
1. The function "ID Log Management" should be set to "Disable"
in Application Setup.
2. Count for Feeder Driven, Error, etc. are not totaled during
this condition is kept.
送料器 ID 履文件存取󳇮󲣄
%s
不能更新保存在周󲲎机器(外部 HDD、DVD 等)的各 ID 履信息。
可能是周󲲎机器生了障碍。
障碍排除之前，如要󱮼󱯂生，可以通󲲜用󲱄件󲢓置
将 ID 履管理󲢓置「无效」即可。
但，󲢓置「无效」期󳋉，不能合󲡶送料次数和吸料出󳇮次数等󳕎目。
Ea12693 Failed to write to the "FEEDER ID LOG" file.
There are not enough space can be used for it, because this disk
is full. Please delete or remove some files to keep enough space.
送料器 ID 履文件󲱨出󳇮󲣄
不能保存送料器 ID 履文件。
磁󱎭空󳋉已󰮶。
󲣌增加保存履文件用磁󱎭的空󳋇容量。
Ea12694 Failed to write to the "FEEDER ID LOG" file.
The attribute of the disk or file may be set as "Read Only".
Please check above.
送料器 ID 履文件󲱨出󳇮󲣄
不能保存 ID 履文件。
󲢺文件是只󲣐文件。
󲣌解除媒体的写保状，
或将要保存的文件的属性更改可写入状。
Ea12695 Failed to write to the "FEEDER ID LOG" file.
feeder ID log file cannot be saved.
It is in the state which cannot be written in.
Please find a cause, and enable it to write.
送料器 ID 履文件󲱨出󳇮󲣄
不能保存送料器 ID 履文件。
目前于不能写入的状。
󲣌󰒺明原因，使其恢至可写入状。
Ea12696 "FEEDER ID LOG" data reset
Log data is reset. Is it all right?
Reset target [%s]
Reset range [All Data]
送料器 ID 履数据初始化
可以履数据行初始化?
初始化象 [%s]
初始化范 [全部数据]
Ea12697 "FEEDER ID LOG" data reset
Log data is reset. Is it all right?
Reset target [%s]
Reset range [Selection line]
ID [%s]
送料器 ID 履数据初始化
可以履数据行初始化?
初始化象 [%s]
初始化范 [所󲳞行的数据]
ID [%s]
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 173 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Feeder set number [%d] 送料器安装号󱓖 [%d]
Ea12698 Failed to write to the "NOZZLE ID LOG" file.
There are not enough space can be used for it, because this disk
is full.
Please delete or remove some files to keep enough space.
Nozzle ID 履文件󲱨出󳇮󲣄
不能保存 Nozzle ID 履文件。
磁󱎭空󳋉已󰮶。
󲣌增加保存履文件用磁󱎭的空󳋇容量。
Ea12699 Failed to write to the "NOZZLE ID LOG" file.
The attribute of the disk or file may be set as "Read Only".
Please check above.
Nozzle ID 履文件󲱨出󳇮󲣄
不能保存 Nozzle ID 履文件。
󲢺文件是只󲣐文件。
󲣌解除媒体的写保状，
或将要保存的文件的属性更改可写入状。
Ea12700 Failed to write to the "NOZZLE ID LOG" file.
Nozzle ID log file cannot be saved.
It is in the state which cannot be written in.
Please find a cause, and enable it to write.
Nozzle ID 履文件󲱨出󳇮󲣄
不能保存 Nozzle ID 履文件。
目前于不能写入的状。
󲣌󰒺明原因，使其恢至可写入状。
Ea12701 "NOZZLE ID LOG" data reset
Log data is reset. Is it all right?
Reset target [%s]
Reset range [All Data]
Nozzle ID 履数据初始化
可以履数据行初始化?
初始化象 [%s]
初始化范 [全部数据]
Ea12702 "NOZZLE ID LOG" data reset
Log data is reset. Is it all right?
Reset target [%s]
Reset range [Selection line]
ID [%s]
Table Number [%d]
Head Number [%d]
Nozzle Type [%s]
Nozzle station number [%d]
Nozzle ID 履数据初始化
可以履数据行初始化?
初始化象 [%s]
初始化范 [所󲳞行的数据]
ID [%s]
工作台号󱓖 [%d]
󲨉装号󱓖 [%d]
吸嘴󱥐型 [%s]
吸嘴交󰀷站号󱓖 [%d]
Ea12703 "NOZZLE ID LOG" data reset
Log data is reset. Is it all right?
Reset target [%s]
Reset range [Selection line]
ID [%s]
Table Number [%d]
Head Number [%d]
Nozzle Type [%s]
Nozzle ID 履数据初始化
可以履数据行初始化?
初始化象 [%s]
初始化范 [Selection line]
ID [%s]
工作台号󱓖 [%d]
Head 号󱓖 [%d]
Nozzle 󱥐型 [%s]
Ea12704 Failed to access to the "NOZZLE ID LOG" file.
%s
To update information for the file on the server, was failed.
There are some possibility of Network Impediment.
Please make sure the condition for above.
Production can be continued with the following condition.
1. The function "ID Log Management" should be set to "Disable"
in Application Setup.
2. Count for Feeder Driven, Error, etc. are not totaled during
this condition is kept.
Nozzle ID 履文件存取󳇮󲣄
不能更新保存在服器中的各 ID 履信息。
可能生了网󱮱障碍。
%s
网󱮱障碍排除之前，如要󱮼󱯂生，可以通󲲜用󲱄件󲢓置
将 ID 履管理󲢓置「无效」即可。
但，󲢓置「无效」期󳋉，不能合󲡶送料次数和吸料次数等󳕎目。
Ea12705 Failed to access to the "NOZZLE ID LOG" file.
%s
To update information for the file on the external storage, was
failed.There are some possibility of Device Impediment.
Production can be continued with the following condition.
1. The function "ID Log Management" should be set to "Disable"
in Application Setup.
2. Count for Feeder Driven, Error, etc. are not totaled during
this condition is kept.
Nozzle ID 履文件存取󳇮󲣄
不能更新保存在周󲲎机器(外部 HDD、DVD 等)中的各 ID 履信息。
可能是周󲲎机器生了障碍。
障碍排除之前，如要󱮼󱯂生，可以通󲲜用󲱄件󲢓置
将 ID 履管理󲢓置「无效」即可。
但，󲢓置「无效」期󳋉，不能合󲡶送料次数和吸料次数等󳕎目。
%s
Ea12708 Moving an XY axis at a safe position... 正在使主机的 XY 󲱉移至安全位置。
Ea12709 Searching a part on a wafer... 正在󰒺找晶片上的元件...
Ea12710 Moving an LCXY axis at a safe position... 正在使相机移至安全位置。
Ea12712 CHARACTER DATA CONVERT
An illegal character is included in the board data.
An illegal character converted as follows and read data.
[ " ] or [ , ] -> [ ^ ]
space -> [ _ ]
other illegal character -> [ ~ ]
An available character is an alphanumeric character and the following signs.
_!#$%&\'\\+-=@(){}:.`^~*<>?/|;
Please don't save it by overwriting when you don't want to change the board data.
Please remove the check from the following check box when you do not want to
convert an illegal character automatically at of the board data reading.
Software Setting - History - Detail History setting - FullASCII Output
文字数据󲱁󰀷
基板程序含有不正确的文字。
已󲣐入将不正确的文字󲱁󰀷成下列文字的数据、
[ " ] 及 [ , ] -> [ ^ ]
半角空格 -> [ _ ]
全角文字、半角片假名、其他使用禁止文字 -> [ ~ ]
使用可能的文字是、半角英文与以下的󲢅号。
_!#$%&\'\\+-=@(){}:.`^~*<>?/|;
不需要更基板程序󰋋、󲣌不要覆盖保存。
󲣐入基板󰋋不需要自󲱁󰀷不正确的文字󰋋
去掉󲳞框中的󲳞中󰓜󲢅。
用程序󲢓置 - 履 - 履󲢻󱮛󲢓置 - 󰓜准文字代󱓖
Ea12713 CHARACTER DATA WARNING
An illegal character is included in the board data.
There is a possibility that the problem occurs when keeping operating it.
文字数据警告
基板程序含有不正确的文字。
如果󱮼󱯂操作、有可能生󳋃󳕭。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 174 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please correct it with off-line software such as YGOS.
An available character is an alphanumeric character and the following signs.
_!#$%&\'\\+-=@(){}:.`^~*<>?/|;
Please put the check from the following check box when you do want to
convert an illegal character automatically at of the board data reading.
Software Setting - History - Detail History setting - FullASCII Output
󲣌用 YGOS 等脱机󲱄件修改。
可以使用文字是半角英文、数字和下列的󲢅号。
_!#$%&\'\\+-=@(){}:.`^~*<>?/|;
需要基板程序󲣐取󰋋自󲱁󰀷不正确的文字󰋋、
󲣌󲳞中下面的󲳞框。
用程序󲢓置 - 履 - 履󲢻󱮛󲢓置 - 󰓜准文字代󱓖
Ea12721 Moving an wafer camera... 正在移晶片相机...
Ea12724 VACUUM CHECK
Vacuum Check is executed.
[OK] Vacuum Check is executed.
[CANCEL] Abort.
真空󰖕󰒺确󲡹
行真空󰖕󰒺。
[OK] 行真空󰖕󰒺。
[取消] 取消行、返回原画面。
Ea12725 Checking VacuumCheck... 正在行真空󰖕󰒺作...
Ea12726 May I switch the edit mode to "Simplicity"?
The input parameter is lost when switching from "Details" to "Simplicity".
可以将󱯫󲱦模式切󰀷成"󱡕易"?
如果从"󲢻󱮛" 切󰀷到 "󱡕易"、会失去󲱨入参数。
Ea12734 Failed in the save of the print inspection result 印刷󰖕󰒺󱮨果的保存失󲧺了。
Ea12738 Print inspection result CSV preservation error
It failed in making the folder that preserved print inspection result CSV.
Please confirm the CSV output folder path of the option setting.
印刷󰖕󰒺󱮨果 CSV 保存󳇮󲣄
建保存印刷󰖕󰒺󱮨果 CSV 的文件失󲧺了。
󲣌确󲡹󲳞󳕎󲢓置画面的 CSV 󲱨出文件的路径。
Ea12739 Print inspection image preservation error
It failed in making the folder that preserved the print inspection image.
Please confirm the image output folder path of the option setting.
印刷󰖕󰒺像保存󳇮󲣄
建保存印刷󰖕󰒺像的文件失󲧺了。
󲣌确󲡹󲳞󳕎󲢓置画面的像󲱨出文件的路径。
Ea12741 Board data is modified.
- Block offset point of the board data is different
from the last production.
- Halfway Continue cannot be done.
Is AutoRun begun from the mount of the first point?
[Yes] :AutoRun Execute
[No] :Not Execute
正在更改基板程序
- 基板程序的拼位移数与前次生󰋋不同。
- 无法施从中途始运行。
是否从始运行?
[是] :始自运行。
[否] :不始自运行。
Ea12743 History preservation connection error
Can not find the preservation.
Possible causes are:
1.A network is not connected.
2.The path setting of History is not correct.
3.No access right for writing data.
Preservation :
履的保存地址󳇮󲣄
没有找到指定的保存地址。
有以下几󱚢原因
1.网󱮱没有󲲳接。
2.󲢓定的保存地址不正确。
3.文件不允󲢍写入。
保存地址 :
Ea12744 Image preservation connection error
Can not find the preservation.
Possible causes are:
1.A network is not connected.
2.The path setting of Image is not correct.
3.No access right for writing data.
Preservation :
画像的保存地址󳇮󲣄
没有找到指定的保存地址。
有以下几󱚢原因
1.网󱮱没有󲲳接。
2.󲢓定的保存地址不正确。
3.文件不允󲢍写入。
保存地址 :
Ea12745 History preservation capacity shortage error
There is no more HDD-space for saving History files.
Data can't be saved any more until more diskspace is
made available:
Preservation :
Capacity : KB
履的保存空󳋉不足󳇮󲣄
所指定的保地址已没有足的空󳋉
保存地址 :
剩余空󳋉 : KB
Ea12746 Image preservation capacity shortage error
There is no more HDD-space for saving Image files.
Data can't be saved any more until more diskspace is
made available:
Preservation :
Capacity : KB
画像的保存空󳋉不足󳇮󲣄
所指定的保地址已没有足的空󳋉
保存地址 :
剩余空󳋉 : KB
Ea12747 The preservation of History is not connected 履的保存地址未󲲳接
Ea12748 The preservation of Image is not connected 画像的保存地址未󲲳接
Ea12749 The preservation of History is uninput 履的保存地址未󲢓定
Ea12750 The preservation of Image is uninput 画像的保存地址未󲢓定
Ea12751 History preservation capacity shortage error Warning
There is no more HDD-space for saving History files.
Data can't be saved any more until more diskspace is
made available:
Preservation :
Capacity : KB
履的保存空󳋉不足󳇮󲣄警告
所指定的保地址已没有足的空󳋉
保存地址 :
剩余空󳋉 : KB
Ea12752 Error Clear 󳇮󲣄已清除
Ea12753 Error Stop 󳇮󲣄停止
Ea12754 Emergency stop 非常停止
Ea12755 Stop by defined production amount of boards 因达到󳕙󲡶生数量而停止
Ea12759 The first equipment was not found
The following first equipment file was not found.
Path:
1. Please confirm the connection of the server.
没有找到最前端󲢓
没有找到以下最前端󲢓的文件。
路径:
1. 󲣌确󲡹服器的󲲳接状。