YAMAHA 报警资料.pdf - 第157页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 157 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 156 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea12253 Writing to %s ... 正在写入%s．．．
Ea12254 Executing of %s ... 正在行%s．．．
Ea12255 WRITE DATABASE
Normal system operation can be interrupted when
data in this database number is changed.
Do you want to write into this database number?
数据逆置
若更改数据号的数据，
系可能不能正常运行。
确行逆置?
Ea12256 CREATE DATABASE
Normal system operation can be interrupted when
data in this database number is changed.
Do you want to create this database number?
新登数据
若更改数据号的数据，
系可能不能正常运行。
确新登?
Ea12257 DELETE DATABASE
Normal system operation can be interrupted when
data in this database number is changed.
Do you want to delete this database number?
除数据
若更改数据号的数据，
系可能不能正常运行。
确要除?
Ea12258 Schedule Task is processing. 正在行度表程。
Ea12260 BLOCK OFFSET ERROR
Block offsets are not valid.
不存在有效的拼位移。
Ea12261 HELPS CODE INITIALIZE
HELPS Code Initialize ?
If you want to change Board data, then you have to select [yes]
and you have to execute [Read Retry] at upstream buffer conveyor.
自切理
从最初始行自切理。
如在下一枚基板行切理(最初始行)，
[是]后，行冲送的[重新行入]。
Ea12262 FIDUCIAL ADJUSTMENT
Fiducial adjustment data will be removed,
if you edit this data.
基准校正
如目，会影响基准校正。
Ea12263 NOT AVAILABLE FOR AUTO NOZZLE CHANGE
This head is not available for auto nozzle change.
It can not take this nozzle.
不可自交吸嘴
指定的装不能行自交吸嘴。
无法使用指定的吸嘴。
Ea12264 BOARD DATA NOT FOUND 没有基板。
Ea12265 SAME FOLDER
The left window is the same as right window.
左画面和右画面的文件相同。
Ea12266 CONVEYOR AND FIX
Please put board on the entrance of conveyor.
The board will be conveyed in and fixed.
基板的入固定
将基板放在送入口。
入基板后，固定基板。
Ea12267 NOZZLE DOWN SENSOR 1 DETECTED
The NOZZLE DOWN SENSOR 1 ERROR
had already been detected.
There are some limitation and danger to continue.
Do you want to continue?
[YES] Continue
[NO] Quit
第 1 下降区域感器的异常
出了第 1 下降区域感器异常。
生很危。
始自运行?
[是] 行
[否] 停止
Ea12268 BOARD EXIST
%s exist.
基板名 %s，已使用。
Ea12269 COULD NOT CONNECT NETWORK DRIVE
Failed to connect to network drive:
Drive Name: %s
Do you want to reconnect this network drive?
[YES] Reconnect
[NO] Quit
网器不能接
不能接网器。
确接的状。
器名: %s
是否再次接此网器?
[是] 再次接
[否] 停止
Ea12270 (Machine Control Command Error) (机器控制指令)
Ea12271 MMF OPEN ERROR MMF 没有打。
Ea12272 COMMAND BUSY 指令行中。
Ea12273 CANNOT EXECUTE COMMAND 指令不能行。
Ea12274 FAILED TO EXECUTE COMMAND 指令的行已失。
Ea12275 TIMEOUT ERROR 生了超。
Ea12276 EXECUTE COMMAND ERROR 指令行。
Ea12277 RESET
Auto running is stopped.
Do you want to reset the machine status?
位
自运行停止状。
要位?
Ea12278 Reset will be executed.
Are you sure?
是否行位?
Ea12279 START RUNNING
Current running speed is %d(%%).
Do you want to run at this speed?
始运行
运行速度置在%d(%%)。
始运行?
Ea12280 CHECK HEAD AND NOZZLE
Required nozzle type is Head %s Nozzle %s.
Please check them.
装/吸嘴 确
元件所需吸嘴是装%s 和吸嘴 %s。
确目前的状。
Ea12281 BOARD DATA LOCATION ERROR
FILE READ ERROR. BECAUSE SETTING LOCATION NOT FOUND.
Please confirm setting location.
基板程序路径
因不存在所路径，所以无法入文件。
确所路径的状。
Ea12300 BOARD READ ERROR
Failed to load board data because the size of board data is too big.
基板入
因基板程序大而不能入。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 157 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Reason: %s
File size: %s byte
Ref.1 %s byte
Ref.2 %s byte
Ref.3 %s byte
原因 %s
文件大小 %s Byte
参考 1 %s Byte
参考 2 %s Byte
参考 3 %s Byte
Ea12301 CONFIRMATION OF FES
Some FES used in this production is not ready.
Please make it ready and select the Button.
[YES] Make it ready
[NO] Nothing
一次性料的确
生基板中定使用的一次性料使用不可状。
安装完一次性料后，以下按。
[是] 上升/固定料
[否] 什也不做
Ea12302 CONFIRMATION OF FES
Some FES used in this production is not ready.
Please make it ready and select the Button.
一次性料的确
生基板中定使用的一次性料不可使用状。
急停机后，安装料。
Ea12303 Setting FES... 正在安装一次性料．．．
Ea12304 Board data operation internal error
ErrorCode : 0x%08X
基板程序操作内部
ErrorCode : 0x%08X
Ea12305 XML operation internal error
ErrorCode : 0x%08X
XML 操作内部
ErrorCode : 0x%08X
Ea12306 Board data operation internal error
ErrorCode : 0x%08X
Though this board data operation is completed,
there is not enough memory.
基板程序操作内部
ErrorCode : 0x%08X
没有充足的内存空可以完成
基板程序的操作。
Ea12307 XML operation internal error
ErrorCode : 0x%08X
Though this XML operation is completed,
there is not enough memory.
XML 操作内部
ErrorCode : 0x%08X
没有充足的内存空可以
完成 XML 操作。
Ea12308 Moving the FES feederplate to the downMoving the FES feederplate down. 正在下降一次性料。
Ea12309 Changing main stopper position... 正在改主板位置．．．
Ea12310 Main-Stopper position is not ready for production.
Do you want to change position?
[OK] continue
[Cancel] abort
主板的位置?
如，按[OK]。
如中止，按[取消]。
Ea12311 Backup completed. 已完成份。
Ea12312 Restore completed. 已完成原。
Ea12313 QRCode Error
Data value is outside the range.
Input 13-digit number.
QR Code
数据在范外。
入 13 位数的数字。
Ea12314 MachineCode Error
The program name which handles MachineCode
isn't found.
MachineCode
没有找到已入的 MachineCode 的程序名。
Ea12315 Now executing inspection. 正在行．．．
Ea12316 Automatic Optimization.
Do you wish to try automatic optimization?
[YES] Automatic Optimization.
[NO] Manual Optimization.
适当找的自化
是否自行适当的找?
[是] 自找适当
[否] 手找适当
Ea12317 Select automatic optimizing parts.
Do you wish to optimize all parts?
[YES] All parts.
[NO] Error parts only.
找象元件
是否行全部元件的找?
[是] 全部元件
[否] 限元件
Ea12318 Finish Automatic Optimization.
Finished automatic optimization.
自找适当束
自找适当已束。
Ea12319 Dispensing... 正在打点．．．
Ea12320 Moving head... 正在移 Head．．．
Ea12321 BOARD DATA CHANGE
Board data is changed.
Failed to save the data because the current operator level is lower.
All changes will be lost.
正在更改基板程序
基板程序已更改。
因置的操作者不同，不能行保存。
更改无效。
Ea12322 Disk is full. 磁已。
Ea12323 QR Code Retry... QR 重新行中．．．
Ea12324 The repair detection of the file.
The machine is unusually shut down.
One or more files may be damaged.
Run the upgrade installation of the application software.
文件的修知
机器异常退出，文件有可能已坏。
行用件升。
Ea12325 QRCode Error
Data value is outside the range.
Input 29-digit number.
QRCode
数据在范外。
入 29 位数的数字。
Ea12326 Board data is modified.
Because Board data is modified,
Halfway continue function cannot be executed.
Board data must be re-loaded.
Please save Board data and select it again.
正在更改基板程序
因基板程序已更改，
所以如要从中途始运行，
必重新入基板程序。
重新基板。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 158 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea12327 MACHINE IS NOT RESET
Do you want to continue to shut down?
机器没有位
是否退出理?
Ea12328 Do you want to clear counter? 初始化数。
您确定?
Ea12329 Drive setting error.
The drive set up can't be used.
Please set up a network drive.
器置
不能使用已置的器。
置网器。
Ea12330 Drive setting error.
The drive set up can't be used.
Please Set up a floppy disk drive or a network drive.
Please setup the network drive using the network button
in 'Network Settings' in 'Software Setting'.
器置
已置的器不能使用。
置器或网器。
置网器，使用用件
置网置内的网接按。
Ea12331 Print Inspection Result Save
Saving the print inspection result...
印刷果保存
正在保存印刷果．．．
Ea12332 Cleaning Nozzles... 正在清点胶嘴．．．
Ea12333 Doing Dipping Test... 正在行点胶嘴打点．．．
Ea12334 Object window size error.
The window size of object data No.%d is bigger than the view window size.
象数据窗尺寸
象数据 No. %d 的窗尺寸置得比
相机的角大。
Ea12335 Object window size error.
The window of object data No.%d is outside the range of the view.
象数据窗尺寸
象数据 No. %d 的窗不在野的范内。
Ea12336 Object window size error.
The window of object data No.%d is outside of the soft limit.
象数据窗尺寸
象数据 No．%d 的窗不在极限的范内。
Ea12337 View position error.
The position of view data No.%d is outside of the soft limit.
野数据位置
野数据 No．%d 的位置不在极限范内。
Ea12338 View data number error.
The total of the view data exceeded a limitation.
野数据数
野数据的数超了限制。
Ea12342 Gerber Conversion Error
Failed to convert G_code
at the %d line in Gerber data file.
GBR
在 GBR 数据文件 %d 行，G 代数据的解析失了。
Ea12343 Gerber Conversion Error
Failed D_code conversion
on the %d line of Gerber data file.
GBR
在 GBR 数据文件 %d 行，D 代数据的解析失了。
Ea12344 Gerber Conversion Error
Failed Gerber data conversion
on the %d line of Gerber data file.
GBR
在 GBR 数据文件 %d 行，
GBR 数据的失了。
Ea12345 Gerber Data File Read Error
Failed to read Gerber data files.
GBR 数据入
GBR 数据文件的入失了。
Ea12346 Aperture Data File Read Error
Failed to read aperture data files.
孔径数据入
孔径数据文件的入已失。
Ea12347 Aperture Data File Write Error
Failed to write aperture data files.
孔径数据写入
孔径数据文件的写入已失。
Ea12348 Inspection Data Matching
Matching the inspection data...
数据匹配
正在行野和象的匹配．．．
Ea12349 Inspection Order Optimize
Optimizing the inspection order...
序最化
正在行野序的最化．．．
Ea12350 Gerber Data Convert
Converting Gerber data...
GBR 数据
正在行 GBR 数据．．．
Ea12351 Moving PPU... PPU 运作中．．．
Ea12352 Start return to PPU origin... 正在行 PPU 返回原点．．．
Ea12353 Moving PPU... 正在移 PPU．．．
Ea12354 Now resetting PPU alarm... 正在行 PPU 警初始化．．．
Ea12355 Failed to write the report file 不能将履出到文件中。
Ea12356 FIRST BOARD CHECK
Please check first Board of a lot by moving
camera. Press the [OK] button to check,
or [CANCEL] button to abort.
After checking and correcting, please start
production.
首件模式
利用移相机目批首件的装。
如行，按 [OK]。
如中止，按[取消]。
完成确后，重新始自运行。
Ea12357 FINAL BOARD CHECK
Please check last Board of a lot by moving
camera. Press the [OK] button to check,
or [CANCEL] button to abort.
After checking and correcting, please start
production.
末件模式
利用移相机目批末件的装。
如行，按 [OK]。
如中止，按[取消]。
完成确后，重新始自运行。
Ea12358 Refill All Components.
Refill all components on %s.
Press the [OK] button to check,
or [CANCEL] button to abort.
元件全部充
%s 上的元件是否已全部充完?
Ea12359 Refill Components.
Please refill each components from Rest Monitor.
元件个充
在余量控屏各元件分行充。