YAMAHA 报警资料.pdf - 第71页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 71 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 70 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea02816 TEMPLATE DATA READ ERRROR
Failed to read Template Data.
模板数据入
模板数据的入已失。
Ea02817 VT FILE CONVERT ERROR
Failed to convert VT file to IBMF file.
VT 文件
VT 文件的 IBMF 已失。
Ea02818 IBMF FILE CONVERT ERROR
Failed to convert IBMF file to VT file.
IBMF 文件
IBMF 文件的 VT 已失。
Ea02819 APPL CPU HANDSHAKE ERROR
Failed to communicate with APPL CPU.
APPL CPU 信号交
与 PPL CPU 的通信已失。
Ea02820 FES FIDUCIAL MARK DATA READ ERROR
Failed to read FES Fiducial data from
Mark-DATABASE.
Database No.
Please check Mark-DATABASE.
料基准校正用数据入
从数据未能入料基准校正
的数据。
数据 号
确数据。
Ea02821 MULTI-MACS DATA TRANSFER ERROR
Multi-Macs Data couldn't be transferred
to vision board.
Multi-MACS 数据送
不能向卡送 Multi-MACS 数据。
Ea02822 ILLEGAL IO ACCESS ERROR
A reference was done toward the illegal IO data.
PORT ID
非法的 IO 操作
操作了非法的 IO 数据。
端口 ID
Ea02823 FULL AUTO MOUNT FEEDBACK (FAMF)
Data of FAMF was initialized.
全自装反(FAMF)
已完成全自装反数据的初始化。
Ea02824 FULL AUTO MOUNT FEEDBACK (FAMF)
Result data of FAMF was totaled.
全自装反(FAMF)
已全自装反的数据。
Ea02825 FULL AUTO MOUNT FEEDBACK (FAMF)
Feedback value was calculated from totaled result.
全自装反(FAMF)
已从合果算出反校正。
Ea02826 FULL AUTO MOUNT FEEDBACK (FAMF)
Feedback value was saved to Machine-Data..
全自装反(FAMF)
已将反校正保存在机器数据中。
Ea02827 ORIGIN INCOMPLETE
Return to origin can not be done.
Because it fails in reading of the necessary data.
返回原点未完成
因所需程序入的失，而不能返回原点。
Ea02828 FAILED TO SEND IO DATA
Update Vacuum Data to IO SYSTEM is failed.
Please run again.
荷数据更新
IO 系的荷数据的更新失了。
再次启运行。
Ea02829 Parts data is not ready.
Please prepare correct parts data.
未准元件数据。
置元件数据。
Ea02830 Fiducial Mark data is not ready.
Please prepare correct mark data.
未准基准校正用的数据。
置数据。
Ea02831 Badmark Mark data is not ready.
Please prepare correct mark data.
未准坏板用的数据。
置数据。
Ea02832 OPERATION START ERROR
A machine adjustment program is starting.
Start operation again after the machine adjustment program completion.
运行始
正在启机器整程序。
退出机器整程序后，再次启运行。
Ea02833 DATABASE
Set all component data from Component-DATABASE has
been completed.
数据信息
已行完元件数据信息的全置。
Ea02834 DATABASE
Set all mark data from Mark-DATABASE has been
completed.
数据信息
已行完数据信息的全置。
Ea02835 SERVICE MODE ERROR
Both sides of service keys are activated.
Set only one key in a Machine.
Both sides of operation are not available.
模式
置了前后两的。
撤一或两的。
否无法操作。
Ea02836 STEP AUTO-RUNNING STOP
Auto-Running was stopped according to step running
command.
分段运行停止
根据分段运行停止指令，停止了运行。
Ea02837 ILLEGAL COMMAND WHILE EDITING
Execution of command is impossible while editing.
中不能行
当基板程序的，不能行。
Ea02838 NO BOARD DATA
Board data does not exist.
没有基板程序
未登基板程序。
Ea02839 RS-232C RECEIVE TIMEOUT
An error occurred with RS-232C communication line.
The cause of the error is receive timeout.
RS-232C 接收超
在 RS232C 通信回上生了接收信号超。
Ea02840 SERVICE MODE
Service key is activated.
Please be careful sufficiently.
Front
Rear
模式
前后中有一的启状。
前
后
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 71 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea02841 SERVICE MODE
Service Mode is finished.
Please be careful sufficiently.
模式
退出模式。
Ea02842 ASSIGNMENT CHECK UN-COMPLETION
The part which hasn't completed an assignment check exists.
Start auto-running again after you confirm an assignment check.
送料器安装位置未完
存在没有完成送料器安装位置的元件。
在确送料器安装位置后，重新始运行。
Ea02843 BOARD DATA ERROR
Reading is failed.
基板程序
因不明原因的，文件的入失了。
Ea02844 RS-232C TRANSMISSION ERROR
A transmission error occurred with RS-232C
communication line.
RS-232C 信
RS232C 的通信路生了信。
Ea02845 C/R BOX FAN STOP
The fan in control box is NG.
C/R BOX FAN STOP
控制箱内的冷却扇已停止。
Ea02846 C/R AC POWER NG
AC power at control box is NG.
C/R AC POWER NG
提供控制箱的 AC100V 异常。
Ea02847 UPS BATTERY LOW
The UPS detected low battery.
UPS BATTERY LOW
UPS 的池正在下降。
Ea02848 UPS AC POWER FAIL
The UPS detected AC power fail.
When count down is completed, shutdown process is started
automatically.
However, in the following case, count down is interrupted
and shutdown process is started instance.
1. When Error Clear Button is pressed.
2. When UPS Battery Low signal is Detected.
UPS AC POWER FAIL
已出 UPS 停。
倒数束的同自始机。
但下列情况下，中断倒数，
立刻始自机。
1. 按下清除按
2. 出 UPS 的池快耗尽
Ea02849 C/R DC POWER NG
DC power at control box is NG.
C/R DC POWER NG
控制箱内的 DC 源异常。
Ea02850 C/R TEMP NG
The temperature is too high.
C/R TEMP NG
控制箱内的温度异常上升。
Ea02851 UPS AC POWER REVIVAL
The UPS detected AC power restored.
UPS AC POWER REVIVAL
UPS 供已恢。
Ea02852 SETTING ERROR
Board data file form is chosen by no more than one.
Please reconfirm setting.
置
没有任何一个基板程序文件形式。
再次确置。
Ea02853 LOT LOG. WRITE ERROR
Failed to write LOT log.
写入批量履
批量履的写入已失。
Ea02854 MOUNT ERROR
During mounting, error on NOZZLE DOWN SENSOR 1
is detected. Please Check condition of the Board.
Mount data
Component data Name
Feeder set position
Pallet set position
<Reason>
-Failure of NOZZLE DOWN SENSOR 1
-Weakness of HEAD DOWN VALVE
元件装
元件装作中，到下降区域感器的异常。
确元件的装状。
装数据 号
元件数据 号 名称
送料器安装位置 号
料架抽出位置 号
<原因>
-下降区域感器的异常
-下降老化
Ea02855 POSSIBILITY OF MISMOUNT
During mounting, error on NOZZLE DOWN SENSOR 1
is detected. Please Check condition of the Board.
<Reason>
-Failure of NOZZLE DOWN SENSOR 1
-Weakness of HEAD DOWN VALVE
In case the reason is not clear, please change machine
setting and continue production.
If a cause can be specified,
Reset deed restoration will be carried out.
存在元件装不良的可能性
元件装作中，已到下降区域感器的异常。
确元件的装状。
<原因>
-下降区域感器的异常
-下降老化
如不能确定原因， 更改机器置。
如果原因能特定，行位操作恢原状
Ea02856 NOT ENOUGH MEMORY
Cannot receive data with RS-232C communication line
because of insufficient memory.
内存不足
RS232C 的通信回，因内存不足，而不能接收程序。
Ea02857 NOT ENOUGH MEMORY
Cannot transmit data with RS-232C communication line
because of insufficient memory.
内存不足
RS232C 的通信回，因内存不足，而不能送程序。
Ea02858 NOT ENOUGH MEMORY
Cannot transmit remote report with RS-232C
communication line because of insufficient memory.
内存不足
RS232C 的通信回，
因内存不足，而不能送通信告。
Ea02859 NOT ENOUGH MEMORY
Cannot receive data with network communication line
because of insufficient memory.
内存不足
网的通信回，因内存不足，而不能接收数据。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 72 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea02860 NOT ENOUGH MEMORY
Cannot transmit data with network communication line
because of insufficient memory.
内存不足
网的通信回，因内存不足，而不能送数据。
Ea02861 NOT ENOUGH MEMORY
Cannot transmit remote report with network
communication line because of insufficient memory.
内存不足
网的通信回，因内存不足，而不能送通信告。
Ea02862 COMMAND COMMUNICATION LINE CONNECT ERROR
Failed to connect network command communication line.
Please confirm the following point.
1.Please check command port number in the communication setting.
2.Please confirm the state of the Windows firewall, in PC
which off-line software is installed.
.Please confirm whether firewall setting is "Invalidity".
.Please confirm whether "YgRemotecontrol" or
a program name of offline software is
set as "an exception", when firewall setting is "effective".
指令通信回接
网的指令通信回的接失了。
确下列各。
1.确通信参数置的指令端口号。
2.在安装脱机件的 PC 上确 Windows 防火的状。
·确是否[无效]。
·如[有效]，作[例外]，
确是否置了[YgRemotecontrol]
或使用中的脱机件的程序名。
Ea02863 COMMAND COMMUNICATION LINE TRANSMISSION ERROR
A transmission error occurred with network command
communication line.
指令通信回送信
网的指令通信回生送信。
Ea02864 COMMUNICATION REPORT LINE CONNECT ERROR
Failed to connect network communication report line.
Please confirm the following point.
1.Please check report port number in the communication setting.
2.Please confirm the state of the Windows firewall, in PC
which off-line software is installed.
.Please confirm whether firewall setting is "Invalidity".
.Please confirm whether "YgRemotecontrol" or
a program name of offline software is
set as "an exception", when firewall setting is "effective".
通信告回接
网的通信告回的接失了。
确下列各。
1.确通信参数置的通信表的端口号。
2.在安装脱机件的 PC 上确 Windows 防火的状。
·确是否[无效]。
·如[有效]，作[例外]，
确是否置了[YgRemotecontrol]
或使用中的脱机件的程序名。
Ea02865 COMMUNICATION REPORT LINE TRANSMISSION ERROR
A transmission error occurred with network
communication report line.
通信告送信
网的通信告回生了送信。
Ea02868 FAILED TO SEND RANDOM BALL DATA
Failed to send the Random Ball Data.
Part data Name
Error Detail No
随机球数据送信
向系送随机球列数据的作已失。
元件信息 号 名称
号
Ea02869 FAILED TO RECEIVE RANDOM BALL DATA
Failed to receive the Random Ball Data.
Part data Name
Error Detail No
随机球数据接收
从系接收随机球列数据的作已失。
元件数据 号 名称
号
Ea02870 FAILED TO READ RANDOM BALL DATA FILE
Failed to read file of the Random Ball Data.
随机球数据文件入
随机球列数据用文件的入的作已失。
Ea02871 FAILED TO WRITE RANDOM BALL DATA
Failed to write file of the Random Ball Data.
随机球数据文件写入
随机球列数据用文件的写入已失。
Ea02872 ILLEGAL VISION FILE NUMBER FOR RANDOM BALL DATA
Illegal number is used on the component.
The value of "OPTION 1" must be except for '0'.
Component data Name
随机球数据送信
随机球列数据用文件号不正确。
元件信息的" 1"，必'0'以外。
元件数据 号 名称
Ea02873 COMMAND COMMUNICATION LINE TIMEOUT ERROR
A timeout error occurred with network command
communication line.
Cannot execute the command.
指令通信回超
网的指令通信回上生了超。
未能行指令。
Ea02874 BOARD AUTO SWITCHING FAILURE
Failed in automatic switching to the interrupted
board data.
基板自切失了
中断基板的自切失了。
Ea02875 INTERRUPTED BOARD DATA FILE NOT FOUND
The Board data file produced before power was switched off
is not found.
没有中断基板文件
找不到源前已行生的基板程序的有文件。
Ea02876 FORCE CONTROL ERROR
No sequence of the force control are found
荷控制
指定的目荷，