YAMAHA 报警资料.pdf - 第235页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 235 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 234 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
the Current Pallet No. of the parts information.
Please reset, and restart at the Halfway Continue.
Mount No.
Head No.
Parts No.
Pulled Pallet No.
Parts Current Pallet No.
Parts Start Pallet No.
Parts End Pallet No.
󲣌行位后，用从中途始运行命令重新始运行。
󲨉装号󱓖
Head 号󱓖
元件号󱓖
抽出的料架号󱓖
元件信息中的当前料架号󱓖
元件信息中的始料架号󱓖
元件信息中的󱮨束料架号󱓖
Ea29200 Auto Tray changer Reset abort error
Aborted the RESET process.
When a pallet is out of the magazine, please remove it
and return it to its assigned magazine by hand.
自托󱎭交󰀷器 位中断󳇮󲣄
位理已中止。
如料架出了料架台󰋋，󲣌用手将其退回收󱮈柜中。
Ea29201 Ext. Tray changer Reset abort error
Aborted the RESET process.
When a pallet is out of the magazine, please remove it
and return it to its assigned magazine by hand.
外部托󱎭交󰀷器 位中断󳇮󲣄
位理已中止。
如料架出了料架台󰋋，󲣌用手将其退回收󱮈柜中。
Ea29202 Ext. Tray changer Reset error
Because the station of ext. tray changer is vacuuming a component,
a component that the head is vacuuming cannot supply to the station.
Please remove the component and retry again.
外部托󱎭交󰀷器 位󳇮󲣄
外部托󱎭交󰀷器的󲱒料站上有元件，
所以 Head 没能将吸附着的元件交󱮮󲱒料站。
󲣌去除元件后，重新行。
Ea29203 Ext. tray changer Reset error
Failed to put the component on the station.
There is a possibility that the component was dropped around the station.
Please remove the component and retry again.
外部托󱎭交󰀷器 位󳇮󲣄
没能在󲱒料站上正确放置元件。
󲱒料站及其周可能有落下的元件存在。
󲣌去除元件后，重新行。
Ea29204 Ext. tray changer Reset error
Failed in component supply from the head of traverser to the station.
There is a possibility
that the component was dropped around the transfer course or the station.
Please remove the component and retry again.
外部托󱎭交󰀷器 位󳇮󲣄
从送小󲰻向󲱒料站交接元件失󲧺了。
送路上或󲱒料站周可能有落下的元件存在。
󲣌去除元件后，重新行。
Ea29210 Auto tray changer Timeout error
The head and Tray changer could not shake hand.
Please inform follows No to the maker.
Error Detail
ATS CTRL No.
自托󱎭交󰀷器 超󰋋󳇮󲣄
主机想要从托󱎭吸附元件，但无法与托󱎭取得一致，所以超󰋋了。
󲣌用下列号󱓖向制造厂商咨󲢷。
󳇮󲣄󲢻󱮛号󱓖 号
ATS CTRL 号󱓖 号
Ea29211 Auto tray changer Pallet status error
The reaction of the stage sensor is abnormal.
Please confirm the state of the sensor and the pallet.
自托󱎭交󰀷器 料架状󳇮󲣄
料架台安装感器的反异常。
󲣌确󲡹感器和料架的状。
Ea29212 Ext. tray changer Head action error
Failed to start the ExtTray Head Action.
Please check the following items:
1. The sensor of Ext.Tray head is broken.
2. Part thickness on a pallet.
3. Tray thickness on a pallet.
外部托󱎭交󰀷器 Head 作󳇮󲣄
外部托󱎭的 Head 未能正常作。
󲣌注意下列󳕎目。
1. Head 上升、下降端感器作不良
2. 料架上的元件厚度
3. 料架上的托󱎭厚度
Ea29220 ILLEGAL BOARD DETECTION ON BUFFER CONVEYOR
During conveyance from the check position to the exit position
by the buffer conveyor,
the Board was simultaneously detected on the following sensors.
the check position sensor and the exit position sensor
When the board is in both the check position sensor
and the exit position sensor of the buffer conveyor,
please take out Either the board.
󱯨冲送装置󰖕出了异常基板
在󱯨冲送装置，从󰖕󰒺位置向出口位置送的󲲜程中，
下列感器同󰋋󰖕出了基板。
󰖕󰒺位置感器和出口位置感器
󱯨冲送装置的󰖕󰒺位置感器和出口位置感器上
同󰋋存在基板󰋋，󲣌取出其中之一。
Ea29221 ILLEGAL BOARD DETECTION ON BUFFER CONVEYOR
During check and conveyance from the check position to the exit position
by the buffer conveyor, the Board was detected on the following sensor.
the entrance position sensor.
When the board is in both the check position sensor
and the entrance position sensor of the buffer conveyor,
please take out the board on the entrance position.
󱯨冲送装置󰖕出了异常基板
在󱯨冲送装置󲲰行󰖕󰒺或从󰖕󰒺位置向出口送的󲲜程中，
下列感器󰖕出了基板。
入口位置感器
󱯨冲送装置的󰖕󰒺位置感器和入口位置感器上
同󰋋存在基板󰋋，󲣌取出入口的基板。
Ea29222 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the entrance position to the check position
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ check position ]
󱯨冲送装置送超󰋋󳇮󲣄
下列基板生了送󳇮󲣄。
从入口位置 向 󰖕󰒺位置 送的基板
可能是因下列原因所致，󲣌采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[󰖕󰒺位置]。
Ea29223 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the check position to the exit position
󱯨冲送装置送超󰋋󳇮󲣄
下列基板生了送󳇮󲣄。
从󰖕󰒺位置 向 出口位置 送的基板
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 235 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ exit position ]
可能是因下列原因所致，󲣌采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[出口位置]
Ea29224 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the exit position to the next machine
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ next machine ]
󱯨冲送装置送超󰋋󳇮󲣄
下列基板生了送󳇮󲣄。
从出口位置 向 下位机 送的基板
可能是因下列原因所致，󲣌采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[下位机]
Ea29225 BUFFER CONVEYOR TRANSFER RECOVERY
Operation of the buffer conveyor is recovered.
Do you take out the Board of the transfer error by hand,
and stop the transfer?
[YES] Take out the Board of the transfer error by hand,
and the transfer is stopped.
[NO] Without taking out a board,
the transfer is restarted as it is.
󱯨冲送装置恢送
恢󱯨冲送装置的送。
是否用手取出生送󳇮󲣄的基板，并中断送?
[是] 取出基板，并中断送。
[否] 不取出基板，在此状下󱮼󱯂始送。
Ea29230 Ext. tray changer Door switch open error
Failed to servo-on because the door switch is 'open'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
外部托󱎭交󰀷器 柜󳊽打󳇮󲣄
因托󱎭的柜󳊽在""位置，所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌将柜󳊽置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29231 Ext. tray changer Magazine clamp error
Failed to servo-on because the magazine is not set correctly.
There is a necessity to lock a door of a tray to reactivate a servo.
Please lock the magazine clamp and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
外部托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因托󱎭的收󱮈柜固定松了，所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌将收󱮈柜固定󳋂，并将柜󳊽置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29232 Ext. tray changer Door close error
Failed to servo-on because the door was closed with the door switch 'close'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'open', and turn it 'close' again.
And press the 'READY' button again after checking the door lock.
外部托󱎭交󰀷器 柜󳊽󳋂󳇮󲣄
因在托󱎭的柜󳊽""位置的状下󳋂了柜󳊽，
所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌先将柜󳊽置""，然后置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29233 Auto tray changer Door switch open error
Failed to servo-on because the door switch is 'open'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
因托󱎭的柜󳊽在""位置，所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌将柜󳊽置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29234 Auto tray changer Magazine clamp error
Failed to servo-on because the magazine is not set correctly.
There is a necessity to lock a door of a tray to reactivate a servo.
Please lock the magazine clamp and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因托󱎭的收󱮈柜固定松了，所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌将收󱮈柜固定󳋂，并将柜󳊽置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29235 Auto tray changer Door close error
Failed to servo-on because the door was closed with the door switch 'close'.
There is a necessity to lock a door of a tray to reactivate a servo.
Please turn the door switch into 'open', and turn it 'close' again.
And press the 'READY' button again after checking the door lock.
自托󱎭交󰀷器 柜󳊽󳋂󳇮󲣄
因在托󱎭的柜󳊽""位置的状下󳋂了柜󳊽，
所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌先将柜󳊽置""，然后置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29236 Auto tray changer Rack protrude error
Failed to servo-on because the magazine is protruded to the door direction.
There is a necessity to lock a door of a tray to reactivate a servo.
Please set the magazine correctly and turn the door switch into 'close'.
And press the 'READY' button again after checking the door lock.
自托󱎭交󰀷器 󲱒料箱出󳇮󲣄
因󲱒料箱向柜󳊽，所以无法启伺服。
了恢伺服，有必要将托󱎭的柜󳊽󳇖定。
󲣌将收󱮈柜安装好，并将柜󳊽置""。
󲣌确󲡹柜󳊽󳇖定后，再按一次'READY'按󳆃。
Ea29237 Auto Tray Crash Warning
There is danger of pallet crash in this state
because returning pallet is failed.
Please be sure to do the following operation.
1. Confirm whether there is no pallet on the pallet stage.
2. Remove by the hand when a pallet exists on the pallet stage.
自托󱎭碰撞警告
料架退回失󲧺。
如󱮼󱯂运行，料架有碰撞的危󳌾。
󲣌必按以下󰠺󳝹位。
1. 确󲡹料架是否从收󱮈柜出。
2. 如有料架出，󲣌用手推回收󱮈柜。
Ea29238 Auto Tray Servo-On Confirmation
Is not there a pallet on the pallet stage?
If there is not pallet on the pallet stage
and there is not danger of pallet crash,
自托󱎭伺服 ON 确󲡹
料架台上留有料架?
如确定料架台上没有料架且不会有碰撞的危󳌾󰋋，
󲣌按[是]。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 236 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
please push [YES] button.
[YES] Restart by pushing the 'ready' button again.
[NO] Cancel.
[是] 按'READY'按󳆃,重新始运行。
[否] 取消。
Ea30200 Convert Auto Wafer Map
Completed successfully.
晶片自󲱁󰀷
已正常󱮨束。
Ea30201 Convert Auto Wafer Map Failed
Undefined error.
晶片自󲱁󰀷失󲧺
生了未定的󳇮󲣄。
Ea30202 Convert Auto Wafer Map Failed
Cannot open read file.
晶片自󲱁󰀷失󲧺
无法打要󲣐取的文件。
Ea30203 Convert Auto Wafer Map Failed
Cannot open write file.
晶片自󲱁󰀷失󲧺
无法打要写入的文件。
Ea30204 Convert Auto Wafer Map Failed
No rank in read file.
晶片自󲱁󰀷失󲧺
要󲣐入的文件没有󳇓接。
Ea30205 Convert Auto Wafer Map Failed
Canceled.
晶片自󲱁󰀷失󲧺
已󱮝止。
Ea30206 Convert Auto Wafer Map Failed
Wafer size is overflow.
晶片自󲱁󰀷失󲧺
超出了最大的晶片尺寸。
Ea30207 Convert Auto Wafer Map Failed
Number of rank kind is overflow.
晶片自󲱁󰀷失󲧺
超出了最大等󱭼󱚢󱥐数。
Ea30208 Convert Auto Wafer Map Failed
Illegal delimiter.
晶片自󲱁󰀷失󲧺
分隔符的位置非法。
Ea30209 Convert Auto Wafer Map Failed
Rank is non-converted.
晶片自󲱁󰀷失󲧺
存在无法󲱁󰀷的等󱭼。
Ea30210 Convert Auto Wafer Map Failed
Line of no rank in read file.
晶片自󲱁󰀷失󲧺
要󲣐入的文件中存在没有等󱭼的行。
Ea30211 Convert Auto Wafer Map Failed
Cannot read font file.
晶片自󲱁󰀷失󲧺
无法󲣐入󲱁󰀷󱓖文件。
Ea30212 Convert Auto Wafer Map Failed
Cannot write font file.
晶片自󲱁󰀷失󲧺
无法写入󲱁󰀷󱓖文件。
Ea30213 Convert Auto Wafer Map Failed
Cannot read option file.
晶片自󲱁󰀷失󲧺
无法󲣐入󲳞󳕎文件。
Ea30214 Convert Auto Wafer Map Failed
Cannot write option file.
晶片自󲱁󰀷失󲧺
无法写入󲳞󳕎文件。
Ea30215 Convert Auto Wafer Map Failed
Cannot read source file.
晶片自󲱁󰀷失󲧺
无法󲣐入要󲱁󰀷的文件。
Ea30216 Convert Auto Wafer Map Failed
Cannot write destination file.
晶片自󲱁󰀷失󲧺
无法写入󲱁󰀷目的位置的文件。
Ea30297 Cannot Run Wafer Map Converter
According to the following reasons, wafer map converter could not be run.
- Reading "WaferMapConverter.ini" file was failed.
- The source folder path set in the file does not exist.
- The source file corresponds to the Wafer Map ID is not found.
晶片󲱁󰀷器无法启
可能是因下列原因，致晶片󲱁󰀷器无法启。
- "WaferMapConverter.ini"的󲣐入失󲧺了。
- 所󲢓置的要󲱁󰀷的文件路径不存在。
- 无法找到与晶片 ID 相的要󲱁󰀷的文件。
Ea30298 Failed To Run Wafer Map Converter
Failed to create process of Wafer Map Converter.
晶片󲱁󰀷器的启失󲧺了
󲲰程的启失󲧺了。
Ea30299 Retry To Convert Auto Wafer Map
Is it converted again?
(However, even if it succeeds in retrying,
when the time-out has been occured to the machine,
it is necessary to restart to run again on the machine.)
晶片自󲱁󰀷重新行
重新行󲱁󰀷?
(注意，即使重新行成功了，
如󲢓生了超󰋋󳇮󲣄，
必󳕐在󲢓重新启运行。)
Ea30301 Matching Condition Data File Write Error
It failed to write the Matching Condition Data file.
Please confirm followings before restart.
1. Please confirm the connection with Management PC or Server PC.
2. Please confirm file path.
[Machine]-[Option Setting]-[Detail Setting]
-[Matching Condition File Path]
位条件数据写入󳇮󲣄
位条件数据的文件写入失󲧺了。
1. 确󲡹管理 PC 或服器的󲲳接状。
2. 确󲡹文件路径的󲢓置。
[机器󲢓置]-[󲳞󳕎󲢓置]-[󲢻󱮛󲢓置]
-[位条件数据文件的路径]
Ea30304 Take over File Write Error
It failed to write the take over file.
Please confirm followings before restart.
1. Check the connection with Server PC.
2. Check the following specification about file path.
[Machine]-[Option Setting]-[Detail Setting]-[Common File Path]
移交文件写入󳇮󲣄
移交文件的写入失󲧺了。
󲣌确󲡹以下内容后重新始运行。
1. 确󲡹服器的󲲳接状。
2. 确󲡹文件路径的󲢓置。
[机器󲢓置]-[󲳞󳕎󲢓置]-[󲢻󱮛󲢓置]-[通用文件路径]
Ea30305 Remove Board
The board was detected in the exit position,
but the matching condition data file is not created.
When it is not created,
3A process control is not operated correctly.
Measure :
1. Please remove the board in the exit position.
2. Please start auto-running again.
󲣌取出基板。
󲍒已在出口位置󰖕出了基板，
但却未建当前的位条件数据文件。
如没有建位条件数据文件，
3A 校正功能将无法正常运行。
解决方法:
1. 󲣌取出出口位置的基板。
2. 󲣌重新始运行。
Ea30311 Remove Board
Matching Condition Data was changed while all boards have not carried out.
󲣌取出基板。
在印刷基板󲲭没有全部出的状下就更改了位