YAMAHA 报警资料.pdf - 第20页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 20 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 19 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea00305 Tray unit error : Unknown component is
on the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 料站上放置了元件。
取出元件。
装数据 号
元件数据 号 名称
料站
Ea00306 Tray unit error : Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架退回收柜。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00307 Tray unit error : Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架从收柜中抽出。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00308 Tray unit error : Failed to start the Hook Action.
Please check the following items:
1. Pallet (No. ) access position.
2. The hook nail.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open..
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP" ON.
2. Remove the pallet from the stage section.
3. Return the pallet to its magazine.
托交器: 抓手未能正常作。
注意以下的目。
1．重新将料架(No. )放置在正确位置。
2．抓手的爪弯曲。
3．抓手感器的作不良。
4．收柜不能正常行收。
5．收的收柜柜敞状。
如料架出了收柜，按下列操作。
1．按下急停机按。
2．取出料架。
3．将料架放回收柜。
Ea00310 Tray unit : The tray unit head or traverser station
has a component attached to its nozzle (pad).
Please remove the component.
托交器: 外部托的 Head 或外部托
料站上存在元件，取出。
Ea00311 Tray unit error: Abort the RESET process.
If a pallet is out of the magazine, please remove it
and store it to its assigned magazine by hand.
托交器
因急停机，料架抽出作中断了。
Ea00313 Tray unit error: The pallet is out of the magazine.
Return the pallet to its assigned magazine.
托交器: 料架出了收柜。
将料架退回收柜。
Ea00314 Tray unit error: The door is open.
Please close the door.
托交器:柜敞着。
敞的柜。
Ea00315 Tray unit error: Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能将料架退回收柜。
将料架退回收柜。
Ea00316 Tray unit error: Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能从收柜中抽出料架。
将料架退回收柜。
Ea00317 TRAY CHANGER ERROR : The door is open.
The door is open or the Z-axis is servo-off.
Please close the door.
(When the door light is off in spite of the door switch 'close',
please make the door switch into 'open' once and make it 'close'.)
托交器 : 柜敞着。
柜敞着，或托交器的 Z 的伺服着。
敞着的柜。
(然柜[]，但柜指示灯不亮灯，
先将柜置[]，然后再置[]。)
Ea00318 Tray unit error : Failed to pick up components from
the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
If this error exist many times, please confirm following,
1.[YTF] Vacuum sensor of the traverser station
2.[SMT] Vacuum valve of the head
3.[TrayChanger] Z-axis
托交器:未能从料站吸附元件。
取出元件。
装数据 号
元件数据 号 名称
料站
如生，下列目。
1．[YTF] 料站的真空感器
2．[片机] 装的吸附
3．[托交器] 料站 Z 坐
Ea00330 The head of the machine or tray-changer is picking a
component. If "SET PALLET" is executed,
component will drop from head.
Remove component from head and execute "SET PALLET"
again.
机器或者托交器呈元件吸附状。
如果此抽出料架，元件可能会脱落。
取出吸附状的元件，并再次行。
Ea00331 TRAY CHANGER ERROR
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
托交器
因托交器陷于了危状或没有料到的状，所以不能重新始运行。
如料架从收柜中出，按下列恢原状。
1. 按急停机按
2. 用手取出料架
3. 按 READY 按
4. 打柜，将料架放回原位
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 20 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
5. Close the door 5. 柜
Ea00332 TRAY CHANGER ERROR
The operation of opening the door was interrupted by EMERGENCY STOP.
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP", Please open the door again and store the
pallet.
(If the door switch is already 'open',
Please make the door switch into 'close' once and make it 'open')
托交器
因急停机等原因，柜打作中断了。
料架可能不在正确的位置上。
解除急停机后，重新打柜装入料架。
(柜已置[]，先将柜置[]，
然后再置[]。)
Ea00333 TRAY CHANGER ERROR
The operation of manual pallet set was interrupted by emergency stop.
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP", Please make the door switch into 'close'
and store the pallet.
托交器
因急停机等原因，手抽出料架的作中断了。
料架可能不在正确的位置上。
解除急停机后，重新打柜放入料架。
Ea00334 TRAY CHANGER ERROR
There is no pallet required in the magazine.
Please check whether the pallet and the magazine are set correctly.
Pallet
托交器
收柜内没有必需的料架。
确料架及收柜是否已正确安装。
料架号 号
Ea00335 TRAY CHANGER ERROR
Can not start production because the operation of manual pallet set is not
completed.
Please put the pallet back in the magazine by opening the door again,
and restart the production.
托交器
因手料架安装作未完成，所以不能始自运行。
打柜安装好料架后，再次启自运行。
Ea00336 TRAY CHANGER ERROR
Can not start production because the operation of opening the door is not
completed.
Though door switch is 'Open', the palette has not been stored yet.
This error is caused by interruptions of opening the door by emergency stop, etc.
Please put the pallet back in the magazine by opening the door again,
and restart the production.
托交器
因以手方式安装料架的作未完成，所以不能始自运行。
柜""，但本收在收柜中的料架却抽出状。
状生在因急停机而引起中断柜打。
打柜安装好料架后，重新始自运行。
Ea00337 Tray changer door opening warning
The magazine rack may not move to the drawer position,
because the door switch was operated quickly.
Please make the door switch into 'close' once (the door light lights),
and make it 'open' again.
托交器柜打警告
因快按柜，所以收柜料箱可能未到达抽出位置。
先将柜置''，等柜指示灯点亮后，再置''。
Ea00338 Tray changer magazine set warning
The magazine rack is not set correctly.
Please check the following points.
1. The magazine clamp must be locked correctly.
2. The pallet suppression of the magazine must be tightened correctly.
3. The pallet not protruding from the magazine.
托交器 收柜安装警告
收柜料箱没有安装好。
确以下目。
1. 收柜固定已。
2. 收柜的料架板已。
3. 料架没有出收柜。
Ea00339 Tray changer door closing warning
The door was closed with the door switch 'close'.
In this state, the tray changer may not work.
Please make the door switch into 'open', and make it 'close' again.
托交器 柜警告
在柜''的状下了柜。
在此状下，托交器可能不能作。
先将柜置''，然后再置''。
Ea00340 TRAY CHANGER DOOR OPENING ERROR
Can not open the door because of the INTERLOCK error.
Please make the door switch 'open' and remove the cause of the INTERLOCK error.
Then please make the door switch 'close' once again.
托交器 柜警告
因正在状，所以不能打柜。
在此状下，托交器可能不能作。
先将柜置''，等排除原因后，
再置''。
Ea00351 INTERLOCK ERROR
The tray unit pallet is out of the magazine.
When you press [READY], you must check the following.
1. Are conditions safe for other people?
2. Are you outside the machine's moving area?
3. Have you returned the pallet to the magazine?
托交器的料架从收柜中出。
按[READY]，注意以下的事。
1．其他人是否在工作
2．是否确保了机械的作范
3．是否已将料架退回收柜
Ea00352 ORIGIN INCOMPLETE
When you press [READY], you must check the following.
1. Are conditions safe for other people?
2. Are you outside the machine's moving area?
3. Have you returned the pallet to the magazine?
返回原点
托交器的料架从收柜中出。
按[READY]，注意以下的目。
1．其他人是否在工作
2．是否确保了机器的作范
3．料架是否已退回收柜
Ea00363 NO COMPONENT FOR USE
All components in alternative loop are not available.
This can be caused by the following:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Tray start No.
Tray end No.
替代元件循的所有元件已不可使用的状。
原因如下:
- 生了吸附或。
- 使用的元件数量已达到指定的数量。
充下列元件后，重新始运行。
元件数据号 号
托始号 号
托束号 号
Ea00365 NO COMPONENT FOR USE 替代元件循的所有元件已不可使用的状。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 21 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
All components in alternative loop are not available.
This can be caused by the followings:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
原因如下:
- 生了吸附和
- 使用的元件数量已达到指定的数量。
充下列元件后，重新始运行。
元件数据 号
Ea00366 All components in alternative loop are not available.
This can be caused by the followings:
- Door of tray unit was opened.
- All components were empty.
Close the door or supply component and run again.
Component data
Tray start No.
Tray end No.
因托交器的柜敞、或元件用完等原因，
下列元件已不可使用的状。
柜或充元件后，重新始运行。
元件数据号 号
托始号 号
托束号 号
Ea00368 PALLET NUMBER ERR
The pallet number detected by sensor is different
from the pulled pallet. Please check inserted
position of this pallet, and run again.
Proper No.
Detected No.
料架号
抽出的料架号与感器出的料架号不一致。
将料架改放于正确的料架，重新始运行。
正确的料架号 号
出的料架号 号
Ea00369 PALLET SET IMPOSSIBLE
One of the doors of the tray changer is open.
Please close all the doors and try again.
不能抽出料架
至少有一扇托交器的柜于敞状。
所有的托交器柜，并行重。
Ea00370 PALLET SET IMPOSSIBLE
The specified pallet number is out of the range.
Please check the pallet number and the machine
data setting.
不能抽出料架
指定的料架号在有效范外。
确料架号以及机器数据。
Ea00371 TRAY CHANGER ERROR
Unknown pallet is detected by the sensor
during pallet action.
Check the pallet sensor.
托交器
在退回/抽出料架的作中，出了不明料架。
确料架感器的状。
Ea00372 TRAY CHANGER ERROR
The destination magazine column is already occupied
by another pallet.
Mount data
Component data Name
Pallet
托交器
料架退回的位置上，
已存在其他料架。
装数据
元件数据 名称
料架号
Ea00373 TRAY CHANGER ERROR
The destination magazine column is already occupied
by another pallet.
托交器
料架退回位置上，已存在其他料架。
Ea00374 TRAY CHANGER ERROR
A pallet is lost by the sensor
during pallet action.
Check the pallet sensor.
托交器
在退回/抽出料架的作中，未能出本存在的料架。
确料架感器的状。
Ea00376 TRAY CHANGER ERROR
Feeder Type of the component information
was defined for Ext.TC or Auto TC,
but no tray changer is configured on this machine.
Please change the setting.
托交器
然托交器不存在，但元件信息中送料器型的置
却[外部托交器]或[自托交器]。
更改置。
Ea00378 CONFIRMATION OF SPECIAL DUMP BACK
A component will be dumped back to the tray.
If you already supply component in the tray unit,
Be sure to press "EMERGENCY STOP" ON, remove the component from the head,
and run again.
Component data Name
托供装置作确
按特殊返理的置，正准将元件放回托。
但，因生托数停止，所以可能已在托
供装置充了元件。如已充，元件会重叠放置，
按急停机按，从 Head 上取出元件后，重新始运行。
元件数据 号 名称
Ea00379 TRAY CHANGER ERROR
The entire parts in that tray are not available
This can be caused by the followings:
- The entire parts is empty.
- Tray unit door is open.
Please supply parts or close the door and
start auto-running again.
Parts No. Name
Start Pallet No.
End Pallet No.
托交器
因托交器的柜被打或元件用完，下列元件
不能使用了。
柜或充元件后，再重新始自运行。
元件数据 号 名称
托始号 号
托束号 号
Ea00380 TRAY CHANGER ERROR
The pallet is protruded from the magazine1 of ATS1.
Please return the pallet to the magazine.
托交器
从 ATS1 的收柜 1 出了料架。
将料架退回收柜。
Ea00381 TRAY CHANGER ERROR
The pallet is protruded from the magazine2 of ATS1.
Please return the pallet to the magazine.
托交器
从 ATS1 的收柜 2 出了料架。
将料架退回收柜。