YAMAHA 报警资料.pdf - 第137页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 137 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 136 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Mask scan position is out of Soft Limit.
Please change the range of mask scan.
网板描野位置在极限范外。
更改网板描范。
Ea08800 DATABASE ERROR
Machine cannot set Mark data,
because Mark type is not "fiducial"
Database No.
数据信息置
指定号的数据的型不是基准，
所以不能置。
数据号
Ea08810 DATA CHECK ERROR
Print Inspection data Error
View data which cope with object data don't exist.
Print Inspection Object Data
Print Inspection View Data
程序
印刷数据。
不存在与象数据相的野数据。
印刷象数据 号
印刷野数据 号
Ea08811 DATA CHECK ERROR
Mask Inspection data Error
View data which cope with object data don't exist.
Mask Inspection Object Data
Mask Inspection View Data
程序
网板数据。
不存在与象数据相的野数据。
网板象数据 号
网板野数据 号
Ea08820 BOARD TRANSFER TIMEOUT ERROR
Failed to load the board from previous machine to upper conveyor.
There is possibility that the board exists on the upper conveyor,
or on the exit of the previous machine's conveyor.
Please check the upper conveyor and remove the board.
基板送超
向入送入口的基板入失了。
上流机送和入送的中部、或入送上可能存在基板。
确入送，如存在基板，取出。
Ea08821 BOARD TRANSFER TIMEOUT ERROR
Failed to load the board from wait position to print position.
There is possibility that the board exists on the upper conveyor,
or main conveyor.
Please check the upper conveyor and the main conveyor.
基板送超
自待机位置向印刷位置的基板送失了。
送和主送的中部上可能存在基板。
Ea08822 BOARD TRANSFER TIMEOUT ERROR
Failed to load the board from print position to exit position.
There is possibility that the board exists on the main conveyor,
or lower conveyor.
Please check the main conveyor and the lower conveyor.
基板送超
自印刷位置向出口位置的基板送失了。
主送和出送的中部上可能存在基板。
Ea08823 BOARD TRANSFER TIMEOUT ERROR
Failed to load the board from exit to next machine.
There is possibility that the board exists on the lower conveyor,
or the entrance of the next machine's conveyor.
Please check the lower conveyor and remove the board.
基板送超
自出送出口的基板出失了。
出送和下流机送的中部、或出送上可能存在基板。
确出送，如存在基板，取出。
Ea08824 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Entrance of the upper conveyor
(2) Wait position of the upper conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 入口
(2) 入送 待机位置
Ea08825 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Wait position of the upper conveyor
(2) Printing position of the main conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 待机位置
(2) 主送 印刷位置
Ea08826 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Exit of the upper conveyor
(2) Printing position of the main conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 出口
(2) 主送 印刷位置
Ea08827 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Entrance of the upper conveyor
(2) Printing position of the main conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 入口
(2) 主送 印刷位置
Ea08828 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Entrance of the upper conveyor
(2) Exit of the upper conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 入口
(2) 入送 出口
Ea08829 BOARD TRANSFER ERROR 基板送
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 137 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Entrance of the upper conveyor
(2) Entrance of the main conveyor
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 入送 入口
(2) 主送 入口
Ea08830 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Printing position of the main conveyor
(2) Exit of the lower conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 主送 印刷位置
(2) 出送 出口
Ea08831 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Exit of the main conveyor
(2) Exit of the lower conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 主送 出口
(2) 出送 出口
Ea08832 BOARD TRANSFER ERROR
Failed to load the board, because the unexpected board exists
on the conveyor.
Please remove the board when the position of the following
board detect sensors is confirmed, and the board exists.
(1) Entrance of the lower conveyor
(2) Exit of the lower conveyor
基板送
因送上存在定数以上的基板，所以基板送失了。
确下列基板感器的位置，如存在基板，取出。
(1) 出送 入口
(2) 出送 出口
Ea08900 Camera axis is moving... 正在移相机...
Ea08901 Supply Board on exit of the conveyer. 将基板插入到送出口。
Ea08902 Remove Board on the upper conveyor. 取出入送上的基板。
Ea08903 Remove Board on the lower conveyor. 取出出送上的基板。
Ea08904 Do you want to clamp the mask?
Please be careful of the mask clamp.
固网板?
将会行网板的固，注意。
Ea08906 Do you want to execute the mask cleaning?
[Yes] The cleaning is executed.
Please select the cleaning method on the following screen.
[No] The cleaning is not executed.
行网板清?
[是] 行清。
在下一画面清方法。
[否] 不行清，退出。
Ea09233 Code scan result 条描果
Es00001 Es00001:CODE ERROR
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00001:未定代
向制造商咨。
原因:
·伺服卡的内部异常。
Es00002 Es00002:INTERNAL ERROR
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00002:内部
向制造商咨。
原因:
·伺服卡的内部异常
Es00003 Es00003:FEEDBACK ERR 0
Servo-motor is not responding to commands from servo-board.
--- CAUSE ---
Mechanical locking in motor-axis.
Failure in connecting motor-encoder cables.
Failure in connecting motor-power cables.
The servo-motor is defective.
The servo-board or the driver-board is defective.
Short in power supply capacity.
--- COUNTERMEASURE ---
Check the mechanical friction in motor-axis.
Check the motor-encoder and motor-power cables.
Replace motor,cable,servo-board,or driver-board.
Check the voltage and capacity of power supply.
Es00003:反 0
伺服达伺服卡的指令没有做出充分答。
原因:
·机械达被定
·器的断、配
·达源的断、配
·伺服达的异常
·伺服卡或卡的异常
·源容量不足
策:
·确机械达的定
·确器的、确达源的配
·更达、、伺服卡、卡
·确源、容量
Es00004 Es00004:FEEDBACK ERR 1
Cannot receive signal of the encoder correctly.
--- CAUSE ---
The encoder cable wiring is incorrect or disconnected.
The servo-motor is defective.
The servo-board is defective.
--- COUNTERMEASURE ---
Wire the encoder cable correctly.
Replace motor,encoder cable,or servo-board.
Es00004:反 1
器的信号不能正确接收信息。
原因:
·器的断、配。
·伺服达的异常
·伺服卡的异常
策:
·确器的配
·更达、器、或伺服卡
Es00005 Es00005:OVER LOAD
Too much load has been detected on servo-motor.
--- CAUSE ---
Es00005:超
在伺服达的中出了异常的超荷。
原因:
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 138 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Mechanical action is not smooth.
The electromagnetic break is defective.
--- COUNTERMEASURE ---
Check load on motor.
Check the electromagnetic break.
·机械作不流
·达制器不良。
策:
·确机械的荷
Es00006 Es00006:Tr.OVER CURRENT
Power module in driver-board detected an overcurrent etc.
--- CAUSE ---
The motor cable wiring is incorrect.
Power module in driver-board is defective.
The motor or servo-board is defective.
--- COUNTERMEASURE ---
Wire the encoder cable correctly.
Replace motor,servo-board,or driver-board.
Es00006:Tr. 超流
已出卡内源模流大等异常。
原因:
·达源的配
·卡内源模的异常
·达，伺服卡的异常
策:
·确达源的配
·更达、伺服卡和卡
Es00007 Es00007:OVER CURRENT
Electric current of servo-motor is over limit.
--- CAUSE ---
Mechanical locking in motor-axis.
Failure in connecting motor-encoder cables.
Failure in connecting motor-power cables.
The servo-motor is defective.
The servo-board or the driver-board is defective.
Short in power supply capacity.
--- COUNTERMEASURE ---
Check the mechanical friction in motor-axis.
Check the motor-encoder and motor-power cables.
Replace motor,cable,servo-board,or driver-board.
Check the voltage and capacity of power supply.
Es00007:超流
伺服达所必要的流超了极限。
原因:
·机械达的上
·器的断或配
·达源的断或配
·伺服达的异常
·伺服卡或卡的异常
·源容量不足
策:
·确机械达的定
·确器、达源的配
·更达、、伺服卡或卡
·确源、容量
Es00008 Es00008:MOTOR OVER HEAT
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00008:达
向制造商咨。
原因:
伺服卡的内部异常。
Es00009 Es00009:Tr. OVER HEAT
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00009:Tr.
向制造商咨。
原因:
伺服卡的内部异常。
Es00010 Es00010:WATCHDOG ERR 0
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00010:器 0
向制造商咨。
原因:
伺服卡的内部异常。
Es00011 Es00011:WATCHDOG ERR 1
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00011: 器 1
向制造商咨。
原因:
伺服卡的内部异常。
Es00012 Es00012:DIVISION ERROR
Please consult your distributor for further information.
--- CAUSE ---
Fatal error occurred in servo-board.
Es00012:除算
向制造商咨。
原因:
伺服卡的内部异常。
Es00013 Es00013:2nd LIMIT OVER
Axis of servo is beyond mechanical limit.
--- COUNTERMEASURE ---
Move relevant axis to center of axis range.
Es00013:2 次极限溢出
表示作范端的感器 (2 次极限感器)正在答。
策:
用手按住的并将其移到作范的中心附近。
Es00014 Es00014:EMERGENCY STOP
"Emergency Stop" switch is "ON".
--- COUNTERMEASURE ---
Check "Emergency Stop" switches or cover etc.
Es00014:急停机中
急停机的射呈 ON 状。
策:
机盖、送机超荷感器、等急停机射的确。
Es00015 Es00015:M.POWER DOWN
Driver Power Voltage is out of range.
--- COUNTERMEASURE ---
Power ON again.
Check the circuit-protector.
Check voltage of power supply.
Es00015:达源降低
卡源超了使用范。
策:
·重新接通源
·确路保器
·确源
Es00016 Es00016:PI1 CON. OFF
Controller front panel connector is not connected properly.
--- COUNTERMEASURE ---
Connect controller front panel correctly.
Es00016:PI1 接插件脱离
控制器前面的接插件的接触异常。
策:
正确接。
Es00017 Es00017:PI2 CON. OFF
Controller front panel connector is not connected properly.
--- COUNTERMEASURE ---
Connect controller front panel correctly.
Es00017:PI2 接插件脱离
控制器前面的接插件的接触异常。
策:
正确接。
Es00018 Es00018:I/O CMU. ERROR
Fatal error occurred in I/O communication.
Es00018:I/O 通信
I/O 通信异常。