YAMAHA 报警资料.pdf - 第227页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 227 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 226 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea29058 Auto tray changer Pallet set error
The head of the machine is picking a component.
If "SET PALLET" is executed, component will drop from head.
Remove component from head and execute "SET PALLET" again.
自托交器 料架抽出
机器或自托交器吸附着元件的状。
此行料架抽出，元件可能掉落。
取出吸附状的元件，并再次行。
Ea29059 Ext. tray changer Pallet set error
The head of the machine or ext. tray changer is picking a component.
If "SET PALLET" is executed, the part will drop from head.
Remove component from the head and retry "SET PALLET" again.
again.
外部托交器 料架抽出
机器或自托交器吸附着元件的状。
此行料架抽出，元件可能掉落。
取出吸附状的元件，并再次行。
Ea29060 Auto tray changer Pallet return error
The destination magazine column is already occupied by another pallet.
Please check whether the pallet isn't set at wrong column.
And please check whether the Pallet Close sensor points to correct position.
Mount data
Component data Name
Pallet No.
Pallet close sensor: Detect pallet
自托交器 料架退回
料架退回位置上已有其他料架存在。
确料架是否安装在了的位置上，
料架退回感器是否指向正确的位置。
装数据 号
元件数据 号 名称
料架号 号
料架退回感器 出料架
Ea29061 Ext. tray changer Pallet return error
The destination magazine column is already occupied by another pallet.
Please check whether the pallet isn't set at wrong column.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Pallet No.
Pallet close sensor: Detect pallet
外部托交器 料架退回
料架退回位置上已有其他料架存在。
确料架是否安装在了的位置上，
料架退回感器是否指向正确的位置。
料架台号 号
料架号 号
料架退回感器 出料架
Ea29062 Auto tray changer Pallet return error
The destination magazine column is already occupied by another pallet.
Please check whether the pallet isn't set at wrong column.
And please check whether the Pallet Close sensor points to correct position.
Pallet close sensor: Detect pallet
自托交器 料架退回
料架退回位置上已有其他料架存在。
确料架是否安装在了的位置上，
料架退回感器是否指向正确的位置。
料架退回感器 出料架
Ea29063 Ext. tray changer Pallet return error
The destination magazine column is already occupied by another pallet.
Please check whether the pallet isn't set at wrong column.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Pallet No.
Pallet close sensor: Detect pallet
外部托交器 料架退回
料架退回位置上已有其他料架存在。
确料架是否安装在了的位置上。
料架退回感器是否指向正确的位置。
料架台号 号
料架号 号
料架退回感器 出料架
Ea29064 Auto tray changer Pallet set error
There is no designated pallet.
Please check whether the pallet and the magazine are set correctly.
Mount data
Component data Name
Pallet
自托交器 料架抽出
指定的料架不存在。
确料架及收柜是否已正确安装。
装数据 号
元件数据 号 名称
料架号 号
Ea29065 Ext. tray changer Pallet set error
There is no designated pallet in the magazine.
Please check whether the pallet is set at correct column.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Pallet No.
Pallet close sensor: Undetect pallet
外部托交器 料架抽出
指定的料架不在收柜中。
确料架是否已正确安装在指定位置上，
料架退回感器是否指向正确的位置。
料架台号 号
料架号 号
料架退回感器 未出料架
Ea29066 Auto tray changer Pallet set error
There is no designated pallet.
Please check whether the pallet and the magazine are set correctly.
自托交器 料架抽出
指定的料架不存在。
确料架及收柜是否已正确安装。
Ea29067 Ext. tray changer Pallet set error
There is no designated pallet in the magazine.
Please check whether the pallet is set at correct column.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Pallet No.
Pallet close sensor: Undetect pallet
外部托交器 料架抽出
指定的料架不在收柜中。
确指定的位置上是否正确安装了料架，
料架退回感器是否指向正确的位置。
料架台号 号
料架号 号
料架退回感器 未出料架
Ea29068 Auto tray changer Pallet set error
There is no designated pallet.
Please check whether the pallet and the magazine are set correctly.
Pallet
自托交器 料架抽出
指定的料架不存在。
确料架及收柜是否已正确安装。
料架号
Ea29069 Auto tray changer Pallet set error
The operation of manual pallet set was interrupted by emergency stop.
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP",
Please make the door switch into 'close' and return the pallet.
自托交器 料架抽出
由急停机等手工料架抽出作中断了。
料架可能没有在正确的位置上。
解除急停机后，打柜，安装好料架。
Ea29070 Auto tray changer Pallet set error
Can not start production because the operation of manual pallet set is not
completed.
Please put the pallet back in the magazine by opening the door again,
自托交器 料架抽出
因手工料架抽出作未完成，所以不能始自运行。
打柜并安装好料架，再重新始自运行。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 227 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
and restart the production.
Ea29071 Ext. tray changer Pallet set error
The head of the machine is picking a component.
If "SET PALLET" is executed, component will drop from head.
Remove component from head and execute "SET PALLET" again.
外部托交器 料架抽出
机器的 Head 正在吸附元件。
行料架抽出，可能致元件掉落。
取出吸附状的元件，并再次行。
Ea29072 Ext. tray changer Pallet set error
The head of the Ext. tray changer is picking a component.
If "SET PALLET" is executed, component will drop from head.
Remove component from head and execute "SET PALLET" again.
外部托交器 料架抽出
外部托交器的 Head 正在吸附着元件。
行料架抽出，可能致元件掉落。
取出吸附状的元件，并再次行。
Ea29073 Ext. tray changer Pallet set error
Cannot set the designated pallet, because the magazine is not set.
Please check whether the magazine of designated pallet is set correctly.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Magazine No.
Pallet No.
Magazine set sensor: Undetect magazine
外部托交器 料架抽出
因没有安装收柜，所以不能抽出指定的料架。
确指定料架的收柜是否已正确置，
收柜安装感器是否正常感。
料架台号 号
收柜号 号
料架号 号
收柜安装感器 未出收柜
Ea29074 Ext. tray changer Pallet set error
Cannot set the designated pallet, because the magazine is not set.
Please check whether the magazine of designated pallet is set correctly.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Magazine No.
Pallet No.
Magazine set sensor: Undetect magazine
外部托交器 料架抽出
因没有安装收柜，所以不能抽出指定的料架。
确指定料架的收柜是否已正确置，
收柜安装感器是否正常感。
料架台号 号
收柜号 号
料架号 号
收柜安装感器 未出收柜
Ea29075 Auto tray changer Dump only pallet set error
There is no designated pallet.
Please check whether the pallet and the magazine are set correctly.
Pallet
自托交器 弃用料架安装
不存在所指定的弃用料架。
确料架以及收柜是否安装正确。
安装料架后，重新始自运行。
料架号 号
Ea29076 Auto Tray Failed to return pallet
Returning pallet was failed for pallet close sensor non-detection.
There is danger of pallet crash in this state.
Please be sure to do the following operation.
1. Confirm whether there is no pallet on the pallet stage.
2. Remove by the hand when a pallet exists on the pallet stage.
Stage No.
Pallet No.
自托料架退回失
料架退回失。料架退回用感器不感。
如持此状，料架有碰撞的危，
所以必按照以下位。
1. 确料架是否从收柜出。
2. 如有料架出，用手推回收柜。
料架台号 号
料架号 号
Ea29080 Auto tray changer Component empty
Component counter reached specified number.
Refill the components and run again.
Component data Name
Start Pallet No.
End Pallet No. [CNTcmp_inf5]
自托交器 元件用完
使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号 名称
料架始号 号
料架束号 [CNTcmp_inf5]号
Ea29081 Ext. tray changer Component empty
Component counter reached specified number.
Refill the components and run again.
Component data Name
Start Pallet No.
End Pallet No. [CNTcmp_inf5]
外部托交器 元件用完
使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号 名称
料架始号 号
料架束号 [CNTcmp_inf5]号
Ea29082 Auto tray changer Component empty
All components in alternative loop are not available.
This can be caused by the followings:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Start Pallet No.
End Pallet No.
自托交器 元件用完
替代元件循的全部元件不可使用的状。
原因如下：
- 生了吸附或。
- 使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29083 Ext. tray changer Component empty
All components in alternative loop are not available.
This can be caused by the followings:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Start Pallet No.
End Pallet No.
外部托交器 元件用完
替代元件循的全部元件不可使用的状。
原因如下：
- 生了吸附或。
- 使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29084 Auto tray changer Components empty
All components in alternative loop are not available.
This can be caused by the followings:
- Door of auto tray changer was opened.
自托交器 元件用完
因柜敞或元件用完等原因，
不能使用下列元件。
柜或充元件后，重新始运行。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 228 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
- All components were empty.
Close the door or supply components and run again.
Component data
Start Pallet No.
End Pallet No.
元件数据 号
料架始号 号
料架束号 号
Ea29085 Ext. tray changer Door opening error
Cannot use the following component because the door is open.
Please close the door and restart production.
Component data
Start Pallet No.
End Pallet No.
外部托交器 柜打
因柜敞着，所以下列元件不能使用。
在柜后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29086 Auto tray changer Components empty
All the tray for the parts are not available.
This can be caused by the followings:
- All the tray is empty.
- Tray changer door is open.
Please supply parts or close the door and
start auto-running again.
Parts No. Name
Start Pallet No.
End Pallet No.
自托交器 元件用完
由柜敞或元件用完等原因，
不能使用下列元件。
柜或充元件后，重新始运行。
元件数据 号 名称
料架始号 [PLTcmp_inf4]号
料架束号 [PLTcmp_inf5]号
Ea29087 Ext. tray changer Component empty
Cannot use the following component because the component is empty.
Please supply the component and restart production.
Parts No. Name
Start Pallet No.
End Pallet No.
外部托交器 元件用完
因元件已用完，所以不能使用下列元件。
在充元件后，重新始运行。
元件数据 号 名称
料架始号 [PLTcmp_inf4]号
料架束号 [PLTcmp_inf5]号
Ea29088 Auto tray changer Confirmation of special dump back
A component will be dumped back to the tray.
If you already supply component in the tray changer,
Be sure to press "EMERGENCY STOP", remove the component from the head,
and run again.
Component data Name
自托交器 供装置作确
按照特殊返理的置，将元件返回到托。
因生托数停止，所以可能已向
托供装置充了元件。
如已充了元件，可能会造成元件的重叠放置，
所以按急停机按，将元件从 Head 上取出后，
再重新始运行。
元件数据 号 名称
Ea29089 Auto tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
自托元件用完停机
以下托元件呈空的状。
充元件后、按指示器按。
元件名称 注
料架始号 号
料架束号 号
Ea29090 Ext. tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
外部托元件用完停机
以下托元件呈空的状。
充元件后、按指示器按。
元件名称 注
料架始号 号
料架束号 号
Ea29100 Auto tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
自托交器 料架抽出
抓手未能正常作。
注意下列目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收柜没有正常安装
5. 收的收柜柜敞着
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29101 Ext. tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托交器 料架抽出
抓手未能正常作。
注意下列目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收柜没有正常收
5. 收的收柜的柜敞着
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29102 Auto tray changer Hook action error
Failed to start the Hook Action.
自托交器 抓手作
抓手未能正常作。