YAMAHA 报警资料.pdf - 第14页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 14 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. A ll Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 13 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Comment
Feeder set position
Pallet set position
Table/Head
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00210 3D RECOGNITION ERROR
During 3D recognition, the part could not be
detected correctly.
Please check component data.
Mount data
Component data Name
Comment
Feeder set position
Pallet set position
Table/Head
3D 元件形状
用 3D 未能正确出元件形状。
确元件数据。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00211 3D HEIGHT RECOGNITION ERROR
During 3D recognition, the lead height
or ball height could not be detected correctly.
Please check component.
Mount data
Component data Name
Comment
Feeder set position
Pallet set position
Table/Head
3D 元件高度出
用 3D 未能正确出引脚或球引脚的高度。
确元件。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00212 3D LEAD BEND ERROR
During 3D recognition, lead bending or pollution
was detected.
Please check component.
Mount data
Component data Name
Comment
Feeder set position
Pallet set position
Table/Head
3D 元件引脚弯曲
用 3D 出了引脚弯曲或屑粘附。
确元件。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00214 3D RECOGNITION PLANE HEIGHT ERROR
During 3D recognition, the height of recognition
plane is larger than the value of "3D Height Check"
in Comp Info.
Please check nozzle and component.
Mount data
Component data Name
Comment
Feeder set position
Pallet set position
Table/Head
3D 面高度
在 3D 中所出的面高度超出了在元件信息
中所置的 3D 面高度。
元件可能没被正确吸附，确吸附状。
装数据 号
元件数据 号 名称
注
送料器安装位置 号
料架抽出位置 号
工作台/Head
Ea00217 FLYING NOZZLE CLUTCH ERROR
Detected a flying nozzle clutch
sensor being ON.
Please check the clutch or sensor status.
This may caused a skipping R-axis belt.
行式吸嘴离合器
行式吸嘴的离合器呈 ON 状。
确离合器和感器的状。
如自运行，R 送可能
会脱离。
Ea00218 FLYING NOZZLE UP SENSOR TIMEOUT ERROR
Flying nozzle up sensor is OFF.
Please check the sensor and remove the cause of
this sensor being OFF.
Machine SensorNo.
AirHead Four Tables(Atable): N00404
AirHead Four Tables(Btable): N08204
AirHead Four Tables(Ctable): N08384
AirHead Four Tables(Dtable): N00584
行式吸嘴交 上升端感器超
因上升端感器 OFF ，所以不能行吸嘴交。
感器状，并排除故障原因。
机 感器 NO.
YG200 :(A 工作台) N00404
YG200 :(B 工作台) N08204
YG200 :(C 工作台) N08384
YG200 :(D 工作台) N00584
Ea00219 BACKLIGHT POSITION ERROR
Please move the backlight to right position
using CHANGE BACKLIGHT command.
背景灯照明位置危
用背景灯照明移指令，
将背景灯照明移至右。
Ea00221 NOZZLE CHANGE ERROR
Head cannot change the nozzle
while it is picking a component.
吸嘴交
因正吸附着元件，所以不能行吸嘴交。
Ea00222 OPERATION ERROR
1. Ensure all nozzles not in use are in station.
2. Ensure the nozzle-sensors detect present nozzles.
3. Press EMG sw. Check the safety of head, nozzles,
and nozzle station.
4. Ensure head down sensors are all ON.
始启危
⒈ 确没有使用的吸嘴全部在吸嘴交站中。
⒉ 确吸嘴交站中的所有吸嘴都使感器生感。
⒊ 按下急停机按，确装、吸嘴、吸嘴交站等的安全。
⒋ 确装不在下降状(装下降端的感器)。
⒌ 确送的危位置上没有基板。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 14 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
5. Ensure no board exists at dangerous position,
6. If steps 1-3 do not solve the problem,
Please ensure safety manually.
⒍ 施以上作后仍不能恢正常，用手方式恢安全。
Ea00223 NOZZLE STATION CLAMPING ERROR
Unable to clamp nozzles in the nozzle station.
Correct the condition of the nozzle station.
吸嘴交站固
无法固吸嘴交站的吸嘴。
确吸嘴是否被卡住。
Ea00224 FLYING NOZZLE POSITION ERROR
Failed to find the flying nozzle position.
Please check nozzle, sensor, and wait position
of R axis.
Head No.
行式吸嘴的位置不明
无法出行式吸嘴的位置。
确吸嘴、感器、待机位置的 R 坐。
装号 号
Ea00225 FLYING NOZZLE ERROR
There is no nozzle present for selection.
Please check flying nozzle specification data.
Head No.
Nozzle Type No.
行式吸嘴状
所指定的吸嘴不在行式吸嘴中。
确行式吸嘴格信息。
装号 号
吸嘴型号 号
Ea00226 FLYING NOZZLE CHANGE ERROR
Possible causes :
1.Unable to clamp flying nozzles. (FullServoMachine)
Please check wait position of R axis.
2.Unable to detect current nozzle. (FullAirMachine)
Please confirm an initial position of N axis.
3.There is a possibility that N axis has rotated while rotating R axis. (FullAirMachine)
Please confirm the state of the FNC lock pin.
Head No.
行式吸嘴固
可能是因下列原因所致。
1.无法固行式吸嘴。(全气机器)
确待机位置的 R 坐。
2.无法出安装着的吸嘴。(全伺服机器)
确 N 的初始位置。
3.R 旋程中，可能 N 也在旋。
装号 号
Ea00227 FLYING NOZZLE EXCHANGE ERROR
Unable to exchange flying nozzles.
Please check vacuum level of lock pin.
Head No.
行式吸嘴交超
无法行行式吸嘴交。
整定的真空确。
装号 号
Ea00228 FLYING NOZZLE EXCHANGE ERROR
Unable to exchange flying nozzles.
Please check vacuum level of lock pin for all heads.
行式吸嘴交超。
无法行行式吸嘴交。
整所有装定的真空确。
Ea00229 FLYING NOZZLE EXCHANGE SENSOR TIMEOUT ERROR
Nozzle down limit sensor is OFF.
Please check the sensor and remove the cause of
this sensor being OFF.
Machine SensorNo.
AirHead Four Tables(Atable): N00405
AirHead Four Tables(Btable): N08205
AirHead Four Tables(Ctable): N08385
AirHead Four Tables(Dtable): N00585
行式吸嘴交 感器超。
因第 2 下降区域感器呈 OFF 状，
所以不能交吸嘴。
感器，并排除故障原因。
机 感器 NO.
YG200 :(A 工作台) N00405
YG200 :(B 工作台) N08205
YG200 :(C 工作台) N08385
YG200 :(D 工作台) N00585
Ea00230 4-Point Fiducial Data Error
Fiducial No.
Setting of [Type] is not correct.
Please set like followings,
No. --> [4Local-M]
No. --> [4Local-S]
4 点基准.数据
基准号 号
号
4 点基准的[]的置不正确。
按如下所示重新置。
号 [4 局部主]
号 [4 局部次]
Ea00232 4-Point Fiducial Data Error
Fiducial No.
Distance between points is too short.
Please set this distance more than 5(mm).
Please set coordinates for 4-point again.
4 点基准.数据
基准号 号
号
4 点基准的 4 点之的距离太近。
4 点之的距离最低置在 5(mm) 以上。
重新置坐。
Ea00233 4-Point Fiducial Data Error
Fiducial No.
In a quadrangle composed of 4-point
fiducials, distance between one point and one
side of quadrilateral is less than 5(mm).
Please set coordinates of 4-point again.
4 点基准.数据
基准号 号
号
由置的 4 点构成的 4 角形的一与其他的
点之的距离在 5.0(mm)以下。
重新置坐，使其大于 5.0(mm)。
Ea00234 4-Point Fiducial Data Error
Fiducial No.
In a quadrangle composed of 4-point
fiducial, there is an interior angle
which is over 180 degrees.
Please set coordinates of 4-point again.
4 点基准.数据
基准号 号
号
由置的 4 点构成的 4 角形的内角中存在超 180 度的角。
重新置坐。
Ea00235 4-Point Fiducial Data Error
Mount Data No.
Fiducial No.
4 点基准.数据
装数据号 号
基准号 号
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 15 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
It is impossible to use this Fiducial number
selected in the Mount Data, because
this data is [4Local-S].
Please use [4Local-M] Fiducial for 4-point
fiducial.
装数据中指定的基准号是[4 局部次]，
所以不能使用。
置 4 点基准的[4 局部主]的基准号。
Ea00236 4-Point Fiducial Data Error
Fiducial No.
It is impossible to use this fiducial data,
because this data is [Note].
Please change from [Note] to [Exec].
4 点基准.数据
基准号 号
基准数据[参考]。
将置修改
[参考] ---> [行]。
Ea00237 BOARD DATA ERROR
Mount data No.
Fiducial data No.
It is impossible to use this fiducial data,
because this data is [Note].
Please change from [Note] to [Exec].
基板程序
的基准数据[参考]。
装数据 号
基准数据 号
将置修改
[参考] ---> [行]。
Ea00238 4-Point Fiducial Data Error
Mount data No.
Fiducial data No.
Coordinate of mount point is out of range for
4-point-fiducial.
Please do not use this 4-point fiducial for this
mount point.
4 点基准.数据
装数据 号
基准数据 号
号
装坐在 4 点基准的有效范外。
于上述装数据，不要使用上述基准数据。
Ea00239 Data Warning
The block that you defined
in Board Information is different
from the local badmark.
Machine cannot count Block Numbers
in Production History.
If you want to count Block Numbers,
change number of block in Board Information.
警告
基板信息内所置的拼个数与正在使用的局部坏板的
个数不同。此，不能正确数生履信息中的生拼
个数。如果想要拼数的，将基板信息内的拼个数
更改使用的局部坏板的合个数。
Ea00240 BOARD DATA ERROR
No mark data available for the local fiducial,
or the mark data is not for fiducial.
Mount Data
Mark data
基板程序
局部基准的数据不存在，
或者数据不基准所用。
装数据 号
数据 号
Ea00243 WARNING: Production
Following conditions are set:
-Board Info.: "Mount" is "Skip".
-Board Info.: "Dot Dispense" is "Skip".
-Mount Info.: There is no valid mount data.
-Dot Disp. Info.: There is no valid dispense data.
-Block Offset Info.: There is no valid block data.
If this error occurred, this board may pass this machine.
警告:生条件
当前置下列条件中的任意一。
·基板信息的"装""跳"。
·基板信息的"正式点胶""跳"。
·装信息中不存在有效的装数据。
·正式点胶信息中不存在有效的点胶数据。
·拼制信息的"行"中不存在需要行的数据。
出警告，基板有可能只是通(不行装或点胶)
片机(点胶机)。
Ea00247 BOARD DATA ERROR
"Mount Action" reserved part number is "Fine
Type", but fine mode reserved head is "Impossible".
Mount data
Head number
Please reserve part number not "Fine Type", etc.
基板程序
指定的元件号的装作 Fine 型，
但所指定的装不能行 Fine 方式的装。
装数据 号
装号 号
指定非 FINE 型的元件号。
Ea00248 COMPONENT DATA ERROR
Feeder Type for this component was not defined.
Specify the feeder type data in Component Info.
Mount Data
Component data Name
元件数据
元件没有指定送料器型。
置元件信息的送料器型。
装数据 号
元件数据 号 名称
Ea00249 COMPONENT DATA ERROR
Pos. Definition must be "Teaching" or "Relative"
for Multi-Stick feeder component.
Input Feeder Pos_X,Y:
In case "Teaching",
from the datum of machine origin.
In case "Relative",
from the datum of 8mm tape feeder pickup position.
Component data Name
元件数据
使用多杆式送料器的元件的送料器位置算
必用[示教]或[相示教]。
[示教]，在吸料位置 X、Y 中入机械位置坐 X、Y，
[相示教]，在吸料位置 X，Y 中入自 8mm 式送料器
的移量。
元件数据 号 名称
Ea00254 SPECIAL LIGHT UPPER SENSOR ERROR
The sensor of special light at the upper end of the
unit does not detect correctly.
The unit does not go up or the sensor does not work
correctly.
Remove the cause of problem.
特殊照明装置上升
特殊照明装置上升端感器没有反。
确特殊照明装置是否没有上升或
特殊照明装置上升端感器是否异常。
排除故障原因。