YAMAHA 报警资料.pdf - 第216页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 216 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 215 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
("Non Barcode") does not exist in the current
board data.
不存在使用虚元件条形的元件。
Ea25569 Dummy Parts Quantity Error
The quantity of the dummy parts is not specified.
Please register the parts quantity at "ID-Editor".
虚元件装料数
没有置虚元件的装料数。
用 ID 器登装料数。
Ea25570 Parts Dump Error
Selected parts cannot be dumped.
Please Dump parts again after stopping auto-running
operation.
元件弃
不能弃所元件。
在停止自运行后，再次弃。
Ea25571 Parts Dump Error
The spliced parts cannot be dumped.
As for the spliced reel, the reel information (reel
file) is automatically dumped when the splicing point
is detected.
元件弃
拼接了料的元件，不能弃。
拼接了料的料，在出料接，
自施旧料的弃作。
Ea25572 Now Checking the Parts Rest Count Information ... 正在行余量管理信息...
Ea25573 Set Number Error
The scanned set number does not exist on this machine.
Please check if the scanned set position is correct.
安装位置
描的安装位置不在机器上。
重新确，是否正在描正确安装位置的条形。
Ea25574 Set Number Error
The scanned set number is not required to setup the
parts in the current board data.
Please check if the set position is correct.
安装位置
您取的安装位置不必行送料器位置置。
重新确是否已安装在正确的安装位置上。
Ea25575 Reel Select Error
The selected reel can be used on other machine.
Please check if the selected reel is correct.
料确定
的料可能其他正在使用。
再次确的料是否。
Ea25576 Reel Select Error
It is failed to identify the reel.
The selected reel can already be used.
Please check the state of the reel to be used.
料确定
的料不存在，或料的确定失了。
再次确的料是否正确。
Ea25577 Splicing Point Detect Error
There are some parts of which the splicing point was not detected.
Please correct the parts rest count or delete the old reel at
the parts remain edit window.
Without executing the above operation at the remain edit window,
machine cannot start auto-running.
Parts name
Parts comment
Feeder set position
Palette set position
接出
在接出范内存在没有出接的元件。
在余量画面中修改拼接了料的元件的剩余数，
或如已更新料，除旧料。
不在余量画面施上述作，就不能行自运行。
名称
注
送料器安装位置
料架抽出位置
Ea25578 PARTS REMAIN STOP
Parts remain count reached to the "Stop Parts Count".
Please refill the parts and start auto-running again.
If the parts rest count is different from the actual rest count,
please correct the parts rest count at the parts remain edit window
and start auto-running,please.
Name
Comment
Palette set position
Parts Stock Position
元件余量停止
下列元件已到达余量停止的数量。
充元件后，重新始运行。
如果数据上的剩余数和的剩余数不相符，
在余量画面中剩余数后，重新始运行。
名称
注
料架安装位置 号()
元件存号 号
Ea25579 SPLICING POINT CHECK
Continuous pickup error more than the splicing point check count was
detected in the splicing point check area.
Is the parts shown below is exactly at the splicing point?
[Yes] The parts used now is switched to the latter one.
And the parts remain count is changed to the one of the latter parts.
[No] The parts used now is still former one.
Parts Name
Parts Comment
Feeder set position
接确
在接出范内出了超接出个数的空位(吸附)。
确下列元件是否在接位置上?
[是] 行接出作并使用新元件的剩余数
[否] 仍使用旧元件的剩余数
元件名称
元件注
送料器安装位置 号
Ea25580 Setup Parts Error
The wrong parts were attached.
Please check whether the right parts are attached.
Feeder Set Position [%s]
Palette Set Position [%s]
Right Parts Name [%s]
安装元件
安装的元件不正确。
确是否安装了正确的元件。
送料器安装位置 [%s]号
料架抽出位置 [%s]号
安装的元件名称 [%s]
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 216 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Right Parts Comment [%s]
Setup Parts ID [%s]
安装的元件注 [%s]
已安装元件的元件 ID [%s]
Ea25581 PARTS SETUP INCOMPLETED
The setup of the following parts are not completed.
Setup the correct parts, and start auto-running
operation after scanning bar code.
Parts Number
Parts Name
Parts Comment
Feeder set position
Palette set position
元件安装未完成
下列元件的安装未完成。
安装正确的元件，并描条形后，
始自运行。
元件号
名称
注
送料器安装位置 号
料架安装位置 号()
Ea25582 PRINTER ITEM SETUP INCOMPLETED
The setup of the following items are not completed.
Setup the correct items, and start auto-running
operation after scanning bar code.
Item Name
Required Item
Operation
印刷部材安装未完成
下列部材的安装未完成。
安装正确的部材，并描条形后
始自运行。
目名称
必部材
作
Ea25583 ITEM SETUP INCOMPLETED
The setup of the following items are not completed.
Setup the correct items, and start auto-running
operation after scanning bar code.
Item Name
Required Item
Operation
部材安装未完成
下列部材的安装未完成。
安装正确的部材，并描条形后
始自运行。
目名
必部材
作
Ea25584 ASSIGNMENT CHECK UN-COMPLETION
The target file which hasn't completed an assignment check exists.
Start auto-running again after you confirm an assignment check.
送料器安装位置未完成
不存在送料器安装位置的目文件。
确送料器安装位置后，重新始运行。
Ea25585 PARTS/FEEDER CONBINATION ERROR
The combination of parts and feeder is not correct.
Please check the correct combination and setup again.
Parts
Feeder
元件/送料器合
元件和送料器的合不正确。
确合后，重新行安装。
元件
送料器
Ea25586 PARTS CONBINATION ERROR
The combination of parts is not correct.
元件合
描到的元件合不正确。
Ea25587 PARTS PREPARATION ERROR
This function is not available for the tray parts and stick parts.
元件准
托元件·料杆元件元件准象之外的元件。
Ea25588 Splicing Error
Splicing of the parts ID which cannot be used is
carried out by this parts name.
Please setup again by another reel (stick).
Name
Comment
Set position
料拼接
拼接的是元件名不能使用的元件 ID。
重新与其他料(料杆)行料拼接。
元件名称
注
安装位置 号
Ea25590 Squeegee Setup Error
The squeegee which cannot be used in this equipment was scanned.
Please setup again by correct squeegee.
Squeegee
刮刀安装
您所描的是本不能使用的刮刀。
描正确的刮刀。
刮刀
Ea25591 File Data Error
Data in the file is abnormal.
文件数据
文件内的数据异常。
Ea25592 Internal Process Error
Abnormality was detected by the following processing.
内部理
在以下理中出了异常。
Ea25593 Item ID Unregistration Error
Item ID of the scanned item is not registered.
Please register item ID in the "ID-Editor".
Item ID
未登部材 ID
您所描的部材的部材 ID 没有登。
用 ID 器登部材 ID。
部材 ID
Ea25594 Unused Item Error
It is an item which is not used in the selected board data.
未使用部材
部材是所基板程序中不使用的部材。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 217 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please cancel the scanning work, and setup a correct item.
取消描作，重新安装正确的部材。
Ea25595 Abnormal within a combination table
Abnormalities were discovered with the table check
created from a LED rank table and the Board data chosen.
- Parts Name of Board data is not exist LED rank table.
Please check in Excel or Editor.
基板程序内存在异常
由 LED 表和所基板程序生成的表了异常。
·基板程序上的元件名，不在 LED 表中。
用 Excel 或 Editor 行确。
Ea25596 Magazine Position Barcode Scan Error
The format of "Magazine Position Barcode" is not correctly registered.
Please confirm whether "TrayChangerType" of "Magazine Position Barcode"
in the Barcode Format Editor is correctly set.
收柜安装位置 描
收柜位置条形格式的登不正确。
确条形格式登，收柜位置条形的
"托供装置"是否置正确。
Ea25597 Tray Changer Type Barcode Scan Error
"TrayChangerType" of scanned barcode is not set to this machine.
Please confirm whether the barcode label is correct.
Scanned TrayChangerType :
托供装置 描
所描的条形的"托供装置"，在机器中没有置。
确条形是否正确。
所描的托供装置 :
Ea25598 Initialize Plate Error
The specified plate was not able to be initialized.
The following causes are thought.
-Neither the Cart nor the Magazine are set at the specified position.
-The plate position and the Magazine position that did not exist were specified.
Specified Plate/Magazine :
送料器架初始化
所指定的送料器架没能初始化。
可能是因下列原因所致。
·所指定的位置上没有安装料、收柜。
·所指定的是不存在的送料器架位置、收柜位置。
指定的送料器架/收柜 :
Ea25600 Board condition un-adjustment.
Please remove the board of %1 and re-supply from upstream conveyer.
基板状不一致
%1 中存在基板，但不存在有效的 ID 信息。
取出%1 的基板。
基板的投入方法
1.从上送装置重新投入。
2.按正确向%1 投入基板。
Ea25601 Board condition un-adjustment.
A board is undetectable although ID information on %1 exists.
Do you want to eliminate ID information?
When '%3' is chosen, ID information is deleted.
When '%2' is chosen, please put a board on %1.
基板状不一致
在%1 存在 ID 信息，但不能出基板。
除 ID 信息?
除%1 的 ID 信息并行当前理，'%3'。
将基板放入%1 并行当前理，'%2'并
将基板放入%1。
Ea25602 ASSY un-registering error
The detected ASSY article watch is not registered into a program list.
Please edit a program list.
ASSY:%s
Surface Information:%s
ASSY 号未登
已出的 ASSY 号没有登在程序列中。
程序列。
ASSY 号 :%s
生面信息 :%s
Ea25603 Board data un-registering error
The Board data which was able to be drawn from the detected ASSY article
watch does not exist in a machine.
Please create Board data to see you edit a program list.
ASSY:%s
Surface Information:%s
Board data:%s
基板程序未登
机器中不存在与出的 ASSY 号的基板程序。
程序列或建基板程序。
ASSY 号 :%s
生面信息 :%s
基板程序 :%s
Ea25604 Put In Board Error
Since production kind information does not exist,
Board cannot be put in.
Since production kind information is reread, put in Board.
中途投入
因不存在生品信息，所以不能行中途投入。
重新入生品信息后，再行中途投入。
Ea25605 BOARD INJECTION DURING PRODUCTION
The board which can be injected currently is
%s
Please make sure the board and put on the %s
in the conveyor.
生中的品投入
当前可以投入的品
%s。
确品后投入%s。
Ea25606 Sign board plan
The following sign board QR information was read
ASSY:%s
Surface Information:%s
Program Name:%s
Board Count:%d
Creation time:%s
Do you want to plan it from this information?
条板切
已入了下列条板 ID 信息。
ASSY 号 :%s
生面信息 :%s
生程序名 :%s
定生枚数:%d
生成日期 :%s
用信息行生品切?
Ea25607 Board ID
Board ID information is removed.
Is it all right?
除基板 ID
除基板 ID 信息。
确行?
Ea25609 The Board has been lost. 失了基板