YAMAHA 报警资料.pdf - 第39页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 39 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 38 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Remove the Board and check the conveyor condition.
Ea00809 QUICK STOP ACTIVE: "Front area sensor"
QUICK STOP FUNCTION is now active.
Remove the cause of QUICK STOP.
[前区域感器]，急停机功能正于有效状。
采取相措施。
Ea00810 QUICK STOP ACTIVE: "REAR area sensor"
QUICK STOP FUNCTION is now active.
Remove the cause of QUICK STOP.
[后区域感器]，急停机功能正于有效状。
采取相措施。
Ea00811 QUICK STOP ACTIVE:
"FRONT-FEEDER PLATE SENSOR 1"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the front
feeder plate is inserted correctly.
一次性安装送料器架用的
[前送料器架起感器 1]
，急停机功能正于有效状。
看送料器架的安装状，采取相措施。
Ea00812 QUICK STOP ACTIVE:
"REAR-FEEDER PLATE SENSOR 1"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the rear
feeder plate is inserted correctly.
一次性安装送料器架用的
[后送料器架起感器 1]
，急停机功能正于有效状。
看送料器架的安装状，采取相措施。
Ea00813 QUICK STOP ACTIVE: "Buffer Conveyor Interlock"
QUICK STOP FUNCTION is now active.
[冲送装置的]，
急停机功能正于有效状。
Ea00814 QUICK STOP ACTIVE: "FRONT-RIGHT FEEDER SENSOR"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the front-right
feeders are inserted correctly.
If the feeder exchange system is used, also ensure
that the system is fixed properly.
[前(右)送料器起出感器]
急停机功能正于有效状。
看送料器的安装状，采取相措施。
如使用一次性料，料的固定状也确。
Ea00815 QUICK STOP ACTIVE: "REAR-LEFT FEEDER SENSOR"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the rear-left
feeders are inserted correctly.
If the feeder exchange system is used, also ensure
that the system is fixed properly.
[后(左)送料器起出感器]
急停机功能正于有效状。
看送料器的安装状，采取相措施。
如使用一次性料，料的固定状也确。
Ea00816 QUICK STOP ACTIVE:
"FRONT-FEEDER PLATE SENSOR 2"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the front
feeder plate is inserted correctly.
一次性安装送料器架用的
[前送料器架起感器 2]，
急停机功能正于有效状。
看送料器架的安装状，采取相措施。
Ea00817 QUICK STOP ACTIVE:
"REAR-FEEDER PLATE SENSOR 2"
QUICK STOP FUNCTION is now active.
To continue, please ensure that the rear
feeder plate is inserted correctly.
一次性安装送料器架用的
[后送料器起感器 2]，
急停机功能正于有效状。
看送料器架的安装状，采取相措施。
Ea00818 QUICK STOP ACTIVE:
"SAFETY SENSOR FOR WIDTH AXIS"
QUICK STOP FUNCTION is now active.
[基板度安全确感器]
，急停机功能正于有效状。
采取相措施。
Ea00819 QUICK STOP ACTIVE:
"ALARM: COOLING FAN X1-AXIS IS NOT WORKING"
QUICK STOP FUNCTION is now active.
Please check the status.
因[X1 达冷却扇停止]，急停机功能正于有效状。
确 X1 达冷却扇的状。
Ea00820 CLEAN-FAN INTERLOCK
Clean-Fan in the machine is not suitable for
production.
You cannot run the machine under this condition.
Please check Clean-Fan.
清扇异常
清扇不正常。
直至其正常止无法运行。
确清扇。
Ea00825 CLEANER BLOWER MOTOR OVERHEATED OR INVERTER FAULT LOAD
The over heat of the blower motor of cleaner unit or
the fault load of inverter was detected.
Possible causes:
(1) Piping of cleaner hose is choked up.
(2) The blower motor may have broken.
(3) The inverter may have broken.
(4) The temperature of blower motor rose by cleaning
continuation execution.
清装置鼓达温度异常或器超荷
已出清装置鼓达温度异常或器超荷。
可能由以下原因造成。
(1) 清装置管道堵塞
(2) 鼓达坏
(3) 器坏
(4) 因清装置持运行而致鼓达的温度上升
Ea00826 INSPECTION CAMERA LIGHT OVERHEATED
Temperature of inspection camera light is too high.
You cannot use inspection camera under this condition.
相机照明温度异常
相机的照明温度不正常。
温度正常后，才能使用相机。
Ea00827 HEAD 1 HEATER TEMPERATURE OVERHEATED
Unusual temperature of the head heater or a
feedback error was detected.
You cannot run the machine under this condition.
Please check Heater condition.
Possible causes:
Temperature sensor broken.
点胶 1 加器高温异常
已出点胶 1 加器高温或反。
排除温度异常后，重新启机器后才能运行。
可能由以下原因造成。
·温度感器的断
·加器的断
·温度感器和加器的分离
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 39 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Heater broken.
No connection between temperature sensor and the heater.
Error in the head IO system.
·Head 的 IO 系的异常
Ea00828 HEAD 2 HEATER TEMPERATURE OVERHEATED
Unusual temperature of the head heater or a
feedback error was detected.
You cannot run the machine under this condition.
Please check Heater condition.
Possible cause:
Temperature sensor broken.
Heater broken.
No connection between temperature sensor and the heater.
Error in the head IO system.
点胶 2 加器高温异常
已出点胶 2 加器高温或反。
排除温度异常后，重新启机器后才能运行。
可能由以下原因造成。
·温度感器的断
·加器的断
·温度感器和加器的分离
·Head 的 IO 系的异常
Ea00829 HEAD 3 HEATER TEMPERATURE OVERHEATED
Unusual temperature of the head heater or a
feedback error was detected.
You cannot run the machine under this condition.
Please check Heater condition.
Possible cause:
Temperature sensor broken.
Heater broken.
No connection between temperature sensor and the heater.
Error in the head IO system.
点胶 3 加器高温异常
已出点胶 3 加器高温或反。
排除温度异常后，重新启机器后才能运行。
可能由以下的原因造成。
·温度感器的断
·加器的断
·温度感器和加器的分离
·Head 的 IO 系的异常
Ea00831 MAIN STOPPER INTERLOCK
Operation of the main stopper in this table height
cannot be performed.
-Please lower the Board table.
Or You can't move table on dangerous position,
because the main stopper is upper.
-Please move main stopper down.
主板上升
此工作台的高度主当板不能工作。
-下降基板工作台。
或、在主当板上升的状下、不能移到
危工作台高度。
-下降主板。
Ea00832 QUICK STOP ACTIVE:
"ALARM: COOLING FAN Y1-AXIS IS NOT WORKING"
QUICK STOP FUNCTION is now active.
Please check the status.
因[Y1 达冷却扇停止]，急停机功能正于有效状。
确 Y1 达冷却扇的状。
Ea00833 QUICK STOP ACTIVE:
"ALARM: COOLING FAN Y2-AXIS IS NOT WORKING"
QUICK STOP FUNCTION is now active.
Please check the status.
因[Y2 达冷却扇停止]，急停机功能正于有效状。
确 Y2 达冷却扇的状。
Ea00834 QUICK STOP ACTIVE:
"ALARM: COOLING FAN WAFER CAMERA LIGHT IS NOT WORKING"
QUICK STOP FUNCTION is now active.
Please check the status.
因[晶片相机照明冷却扇停止]，急停机正于有效状。
确晶片相机照明冷却扇的状。
Ea00848 QUICK STOP ACTIVE:
"ALARM: IONIZER IS ABNORMAL"
QUICK STOP FUNCTION is now active.
Please check the status.
因"离子生器异常"
急停机功能正于有效状。
确离子生器的状。
Ea00850 INTERLOCK ERROR
Head down sensor is OFF.
Remove the cause of this sensor being OFF.
存在下降端感器呈 OFF 状的 Head。
明原因并解决。
Ea00851 INTERLOCK ERROR
Transfer axis up/down sensor is OFF.
Remove the cause of this sensor being OFF.
基板送机的下降端感器呈 OFF 状。
明原因并解决。
Ea00852 INTERLOCK ERROR
The sensor for main stopper, push-up or
entrance stopper is ON.
Remove the cause of this sensor being ON.
主档板、、入口板中的某个感器呈 ON 状。
明原因并解决。
Ea00860 INTERLOCK ERROR
External Tray Changer head is down now.
Please change the output to up in MANUAL.
外部托 Head 的下降端感器呈 OFF 状。
明原因并解决。
Ea00861 INTERLOCK ERROR
A pallet from tray unit is out from the rack.
Please put it into the rack.
托交器的料架出了收柜。
把料架退回收柜。
Ea00862 INTERLOCK ERROR
One pallet from tray unit is on the table.
Please put it into the rack.
工作台上有托交器的料架存在。
把料架退回收柜。
Ea00863 INTERLOCK ERROR
Pallet latch condition is illegal.
Possible cause:
1.The open/close sensor of Pallet latch is in the unusual
state.
2.It is going to take pallet in the state where tray unit
is closed door has closed and latch is also closed.
料架的状不正确。
确感器的状。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 40 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Or it has made a mistake and reacted, latch may not have
carried out normal operation of whether latch sensor is out
of order.
Please check latch sensor and tray unit.
Ea00864 INTERLOCK ERROR
You can't move X ,Y ,R or W axis,
because Z axis is moving or Z axis position
safety sensor is OFF.
Please check Z axis position.
Head 的高度在危位置上，
因而不能移 X、Y、R、W 。
Z 正在移或 Z 安全感器呈 OFF 状。
把 Head 移至安全高度。
Ea00865 INTERLOCK ERROR
You can't move X or Y axis,
because there isn't a nozzle station at the bottom.
因吸嘴交站不在下降端，
所以 X、Y 不能移。
Ea00866 INTERLOCK ERROR
You can't move Z axis,
because X or Y axis is moving.
因 X、Y 正在移，所以不能移 Z 。
Ea00869 <<<WARNING SENSOR ERROR>>>
Head down sensor or Lower Sensor is OFF in A-table.
Please check sensor and remove the cause of
this sensor being OFF.
If you don't remove the cause, it is impossible
to start production.
<<<警告 感器异常>>>
在 A 工作台，出了[吸嘴下降状]。
下降端感器，或第 1 下降区域感器呈 OFF 状。
感器，明故障原因并解决。
如没有解决，不能始自运行。
Ea00870 <<<WARNING SENSOR ERROR>>>
Head down sensor or Lower Sensor is OFF in B-table.
Please check sensor and remove the cause of
this sensor being OFF.
If you don't remove the cause, it is impossible
to start production.
<<<警告 感器异常>>>
在 B 工作台，出了[吸嘴下降状]。
下降端感器，或第 1 下降区域感器呈 OFF 状。
感器，明故障原因并解决。
如没有解决，不能始自运行。
Ea00871 <<<WARNING SENSOR ERROR>>>
Head up-down action is abnormal.
Following reasons are possible.
- Board fixation is not correct.
- PickHeight or MntHeight is not correct.
- The head lower-end sensor does not function.
- The head lowering valve does not function.
- The nozzle shaft is bent.
- The head did not reach the bottom within 1 sec.
<<<警告 感器异常>>>
Head 的上下作异常，可能由以下原因造成。
- 基板的固定异常。
- 吸料高度、装高度异常。
- 下降端感器异常。
- Head 下降的作异常。
- 已形。
- 在下降始后 1 秒内未能到达下降端。
Ea00872 INTERLOCK ERROR
You can't move X or Y axis,
because there isn't a special light at the bottom.
因特殊照明装置不在下降端，
所以不能移 X、Y 。
Ea00874 INTERLOCK ERROR
You can't move W axis, because the safety sensor
on buffer conveyor is ON.
因冲送装置上的区域感器呈 ON 状，
所以不能移 W 。
Ea00876 INTERLOCK ERROR
You can't move TrayChanger Z axis,
because Magazine Clamp condition is illegal.
Be sure to press "EMERGENCY STOP" ON and open a door.
Please check fix of Magazine and Magazine Clamp
sensor and run again.
因托交器的收柜固的状不正确，所以无法启。
置急停机状，并打柜，然后确收柜的固定
状和收柜固感器的状。
Ea00877 INTERLOCK ERROR
There is contradiction in the output and the input
about FNC Clutch Clamp.
In this situation, R-axis can't be worked.
Please check as following:
1.Sensor about Fnc Clutch
2.Machine data [INIT MOVE] for R-axis.
因 FNC 离合器的入、出状不正确，
所以不能移 R 。
下列目。
1．FNC 离合感器的状
2．机器数据[R 初始移]的数
Ea00879 <<WARNING SENSOR ERROR>
NOZZLE DOWN LIMIT SENSOR CHECK ERROR
Nozzle down limit sensor is ON even when the head
reach lower-end.
The sensor condition is not correct and this may
cause big problem.
Please check the sensor and remove the cause of
this sensor keeps being ON.
TABLE
Error Detail No.
<<重大>>
第 1 下降区域感器
然下降端感器于 OFF 状，但第 1 下降区域感器仍 ON。
如在此状下自运行，有可能造成装坏等重大事故。
立即第 1 下降区域感器。
工作台号
No.
Ea00880 <<WARNING VACUUM LEVEL ERROR>
MOUNT IO SEQUENCE VACUUM LEVEL ERROR
Vacuum level has not reached the specified level.
Please check the nozzle and valve condition.
This may cause bring-back cmp. or double mount
problem.
<<重大>>
IO 作流程装元件气
在装元件未能充分降低气。
因元件可能被回，所以立即吸嘴和等。
如在此状下自运行，可能会引起元件被
回或重装等。