YAMAHA 报警资料.pdf - 第120页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 120 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 119 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
1. The board has stuck to the mask.
2. The board dropped from the conveyor.
Please remove a mask and be sure to
check the state of the printed board.
Plaease remove the board and restart auto running after reset.
(2) 印刷位置上没有基板。
(3) 送出口有基板。
Ea08222 BOARD TRANSFER ERROR
Failed to carry Board from print position to entrance of
the main conveyor.
基板送󳇮󲣄
从印刷主机送印刷位置到入口的基板
送失󲧺了。
Ea08223 BOARD TRANSFER ERROR
Failed to carry Board from print position to exit of the
main conveyor.
基板送󳇮󲣄
从印刷机主机送印刷位置到出口的基板
送失󲧺了。
Ea08224 BOARD TRANSFER ERROR
Failed to carry Board from print position to extended
guide of the main conveyor.
基板送󳇮󲣄
从印刷机主机送印刷位置到延󳉔送󲰽的
基板送失󲧺了。
Ea08225 BOARD TRANSFER ERROR
Failed to carry Board slowly to exit of the main conveyor.
基板送󳇮󲣄
向印刷机主机送出口的基板的低速送失󲧺了。
Ea08226 BOARD TRANSFER ERROR
Failed to unload Board from entrance of the main conveyor.
基板送󳇮󲣄
自印刷机主机送入口的
基板出失󲧺了。
Ea08227 BOARD TRANSFER ERROR
Failed to unload Board from exit of the main conveyor.
基板送󳇮󲣄
自印刷机主机送出口的
基板出失󲧺了。
Ea08228 BOARD TRANSFER ERROR
Failed to unload Board out of the main conveyor.
基板送󳇮󲣄
自印刷机主机送的基板出失󲧺了。
Ea08229 BOARD TRANSFER ERROR
No Board is supplied on entrance of the main conveyor.
基板送󳇮󲣄
没有向印刷机主机送入口供基板。
Ea08230 BOARD TRANSFER ERROR
No Board is supplied on extended guide of the main
conveyor.
基板送󳇮󲣄
没有向印刷机主机延󳉔送󲰽
供基板。
Ea08231 BOARD TRANSFER ERROR
Unable to load Board into the upstream buffer conveyor.
Possible causes:
(1) There is a Board on entrance of the upstream buffer
conveyor.
(2) There is a Board on exit of the upstream buffer conveyor.
基板送󳇮󲣄
不能向上流󱯨冲送入基板。
可能由以下原因造成的。
(1) 󱯨冲送入口有基板。
(2) 󱯨冲送出口有基板。
Ea08232 BOARD TRANSFER ERROR
Failed to load Board into the upstream buffer conveyor.
基板送󳇮󲣄
向上流󱯨冲送的基板入失󲧺了。
Ea08233 BOARD TRANSFER ERROR
Failed to carry Board from entrance to exit of the upstream
buffer conveyor.
基板送󳇮󲣄
从上流󱯨冲送入口到上流󱯨冲
送出口的基板送失󲧺了。
Ea08234 BOARD TRANSFER ERROR
Failed to carry Board from exit to entrance of the upstream
buffer conveyor.
基板送󳇮󲣄
从上流󱯨冲送出口到上流󱯨冲
送入口的基板送失󲧺了。
Ea08235 BOARD TRANSFER ERROR
Failed to unload Board from exit of the upstream buffer
conveyor.
基板送󳇮󲣄
自上流󱯨冲送出口始的基板出失󲧺了。
Ea08236 BOARD TRANSFER ERROR
Failed to unload Board out of the upstream buffer conveyor.
基板送󳇮󲣄
自上流󱯨冲送始的基板出失󲧺了。
Ea08237 BOARD TRANSFER ERROR
Unable carry Board from the upstream buffer conveyor.
Possible cause:
(1) There are Boards on the entrance and exit of the
upstream buffer conveyor.
基板送󳇮󲣄
不能在上流󱯨冲送上送基板。
可能由以下原因造成的。
(1) 󱯨冲送入口和出口两都有基板。
Ea08238 BOARD TRANSFER ERROR
Unable to load Board into the downstream buffer conveyor.
Possible causes:
(1) There is a Board on entrance of the downstream buffer
conveyor.
(2) There is a Board on exit of the downstream buffer conveyor.
基板送󳇮󲣄
不能向下流󱯨冲送入基板。
可能由以下原因造成的。
(1) 󱯨冲送入口有基板。
(2) 󱯨冲送出口有基板。
Ea08239 BOARD TRANSFER ERROR
Failed to load Board into the downstream buffer conveyor.
基板送󳇮󲣄
向下流󱯨冲送入基板失󲧺了。
Ea08240 BOARD TRANSFER ERROR
Failed to carry Board from entrance to exit of the downstream
buffer conveyor.
基板送󳇮󲣄
自下流󱯨冲送入口到下流󱯨冲
送出口的基板送失󲧺了。
Ea08241 BOARD TRANSFER ERROR
Failed to carry Board from exit to entrance of the downstream
buffer conveyor.
基板送󳇮󲣄
自下流󱯨冲送出口到下流󱯨冲
送入口的基板送失󲧺了。
Ea08242 BOARD TRANSFER ERROR
Failed to unload Board from entrance of the downstream buffer
conveyor.
基板送󳇮󲣄
自下流󱯨冲送入口的基板出失󲧺了。
Ea08243 BOARD TRANSFER ERROR
Failed to unload Board from exit of the downstream buffer
基板送󳇮󲣄
自下流󱯨冲送出口的基板出失󲧺了。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 120 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
conveyor.
Ea08244 BOARD TRANSFER ERROR
Failed to unload Board out of the downstream buffer conveyor.
基板送󳇮󲣄
自下流󱯨冲送的基板出失󲧺了。
Ea08245 BOARD TRANSFER ERROR
Unable carry Board on the downstream buffer conveyor.
Possible causes:
(1) There is Board at both entrance and exit of the
downstream buffer conveyor.
基板送󳇮󲣄
不能在下流󱯨冲送上送基板。
可能由以下原因造成的。
(1) 󱯨冲送入口和出口两都有基板。
Ea08246 BOARD TRANSFER ERROR
Cannot unload the Board on the downstream buffer conveyor.
Please press "Supply Board" button and RUN button to
supply Board on the downstream buffer conveyor manually for
unload.
基板送󳇮󲣄
不能送在下流󱯨冲送上󰖕出的基板。
将基板放入下流󱯨冲送󰋋，󲣌先按
"放入基板"按󳆃，再按 RUN 按󱮒，再次
启自运行。
Ea08247 SUPPLY BOARD
Board is ready to unload to the next machine.
Please supply the Board at exit of the downstream
buffer conveyor and press RUN button to restart.
If you want to cancel supply, release "Supply Board"
button and press RUN button to restart.
󲣌放入基板。
已作好将基板放入下流󱯨冲送的准。
󲣌将基板放入下流󱯨冲送的出口位置，
然后按 RUN 按󳆃，再次启自运行。
如中断基板的放入，󲣌先解除"基板放入"
按󳆃，然后按 RUN 按扭，再次启自运行。
Ea08248 BOARD TRANSFER ERROR
Failed to load Board from exit of the upstream buffer
conveyor.
基板送󳇮󲣄
自上流󱯨冲送出口的基板入失󲧺了。
Ea08249 BOARD TRANSFER ERROR
Failed to load Board from entrance of the downstream buffer
conveyor.
基板送󳇮󲣄
自下流󱯨冲送入口的基板入失󲧺了。
Ea08250 ILLEGAL BOARD DETECTION ON MAIN CONVEYOR ENTRANCE
Illegal Board is detected on the entrance sensor of the main
conveyor.
More than 2 boards may exist on the main conveyor.
Please check the boards on the main conveyor and remove all
the boards on the main conveyer.
Please restart Auto-Running after Reset.
印刷机主机入口感器󰖕出异常基板
在印刷机主机送的入口感器󰖕出了异常基板。
主机送上可能存在数个基板。
󲣌确󲡹主机送上的基板，并取出所有基板。
若要再次启自运行，󲣌先󲲰行位。
Ea08253 ILLEGAL BOARD DETECTION ON MAIN CONVEYOR EXIT
Illegal Board is detected on the exit sensor of the main
conveyor.
More than 2 boards may exist on the main conveyor.
Please check the boards on the main conveyor and remove all
the boards on the main conveyer.
Please restart Auto-Running after Reset.
印刷机主机出口感器󰖕出异常基板
在印刷机主机送的出口感器󰖕出了异常基板。
主机送上可能存在数个基板。
󲣌确󲡹主机送上的基板，并取出所有基板。
若要再次启自运行，󲣌先󲲰行位。
Ea08254 ILLEGAL BOARD DETECTION ON MAIN CONVEYOR
The Boards were detected simultaneously on the entrance sensor
and print position sensor of the main conveyor.
Please remove boards on the entrance sensor and the print
position sensor of the main conveyor.
Please restart Auto-Running after Reset.
印刷机主机送上异常基板󰖕出
印刷机主机送的入口感器和固定位置感器上同󰋋󰖕
出了基板。
󲣌取出主机送入口和固定位置感器上的基板。
若要再次启自运行，󲣌先󲲰行位，然后再次启运行机器。
Ea08255 ILLEGAL BOARD DETECTION ON MAIN CONVEYOR
The Board was detected simultaneously on the entrance sensor
and exit sensor of the main conveyor.
Please remove boards on the entrance sensor and the exit
sensor of the main conveyor.
Please restart Auto-Running after Reset.
印刷机主机送上异常基板󰖕出
印刷机主机送的入口感器和出口感器上同󰋋󰖕
出了基板。
󲣌取出主机送入口和出口感器上的基板。
若要再次启自运行，󲣌先󲲰行位。
Ea08256 ILLEGAL BOARD DETECTION ON UPSTREAM BUFFER CONVEYOR
The Board was detected simultaneously on the entrance sensor
and exit sensor of the upstream buffer conveyor.
Please remove boards on the entrance sensor and the exit
sensor of the upstream buffer conveyor.
Please restart Auto-Running after Reset.
上流󱯨冲送异常基板󰖕出
上流󱯨冲送的入口感器和出口感器上同󰋋󰖕
出了基板。
󲣌取出上流󱯨冲送入口和出口感器上的基板。
若要再次启自运行，󲣌先󲲰行位。
Ea08257 ILLEGAL BOARD DETECTION ON DOWNSTREAM BUFFER CONVEYOR
The Board was detected simultaneously on the entrance sensor
and exit sensor of the downstream buffer conveyor.
Please remove boards on the entrance sensor and the exit
sensor of the downstream buffer conveyor.
Please restart Auto-Running after Reset.
下流󱯨冲送异常基板󰖕出
下流󱯨冲送的入口感器和出口感器上同󰋋󰖕
出了基板。
󲣌取出下流󱯨冲送入口和出口感器上的基板。
若要再次启自运行，󲣌先󲲰行位。
Ea08267 ILLEGAL BORAD DETECTED BETWEEN THE STAGE
There is a Board on the edge of the moving conveyor.
Please resume automatic operation after checking
around a sensor which detected abnormality and
solving abnormalities.
Stage:
1:UPPER STAGE 2:LOWER STAGE
Sensor:
1:ENTRANCE CONVEYOR 2:UPPER STAGE ENTRANCE
基板固定󰋋，在中󲱁部感到基板。
基板固定󰋋，在送中󲱁部󰖕出了异常。
󲣌确󲡹󰖕出异常的感器周，去除异常情况后，
重新始自运行。
象基板台 :
1:上流基板台 2:下流基板台
象感器:
1:入送 2:上流基板台入口
3:上流基板台出口 4:下流基板台入口
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 121 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
3:UPPER STAGE EXIT 4:LOWER STAGE ENTRANCE
5:LOWER STAGE EXIT 6:EXIT CONVEYOR
5:下流基板台出口 6:出送
Ea08270 UNABLE TO CONNECT CLEANER
Unable to connect cleaner with Board table.
Possible causes:
(1) Cleaner is already connected with Board table.
(2) Cleaner is not fixed on the base.
不能󲲳󱮨清󰧖装置
不能将清󰧖装置󲲳󱮨在基板工作台。
可能因下列原因所致。
(1) 清󰧖装置与基板工作台已󱮤󲲳󱮨。
(2) 清󰧖装置没有固定在基座上。
Ea08271 UNABLE TO CLEAN MASK
Unable to work cleaner.
Possible causes:
(1) Cleaner is not connected with Board table.
(2) Cleaner is fixed on the base.
(3) Cleaner is not in lower position.
不能清󰧖
不能󲲰行清󰧖。
可能因下列原因所致。
(1) 清󰧖装置与基板工作台分离状。
(2) 清󰧖装置固定在基座上。
(3) 清󰧖装置未下降。
Ea08272 UNABLE TO SEPARATE CLEANER
Unable to separate cleaner with Board table.
Possible causes:
(1) Cleaner is already separated from Board table.
(2) Cleaner is fixed on the base.
不能分离清󰧖装置
不能将清󰧖装置与基板工作台分离。
可能因下列原因所致。
(1) 清󰧖装置与基板工作台已󱮤分离。
(2) 清󰧖装置固定在基座上。
Ea08273 CLEANER CONNECT ERROR
Failed to connect cleaner with Board table.
󲲳󱮨清󰧖装置󳇮󲣄
清󰧖装置与基板工作台的󲲳󱮨失󲧺了。
Ea08274 CLEANER SEPARATE ERROR
Failed to separate cleaner from Board table.
分离清󰧖装置󳇮󲣄
清󰧖装置与基板工作台的分离失󲧺了。
Ea08275 CLEANER FIX ERROR
Failed to fix cleaner on the base.
清󰧖装置固定󳇮󲣄
将清󰧖装置固定在基座的作已失󲧺。
Ea08276 CLEANER RELEASE ERROR
Failed to release cleaner from the base.
清󰧖装置解除固定󳇮󲣄
从基座松清󰧖装置的作失󲧺了。
Ea08277 CLEANER UP ERROR
Failed to move cleaner up.
清󰧖装置上升󳇮󲣄
清󰧖装置不能上升。
Ea08278 CLEANER UP ERROR
Failed to move cleaner down.
清󰧖装置下降󳇮󲣄
清󰧖装置不能下降。
Ea08279 GAUZE ROLLING FINISHED
All gauze has been rolled up.
Please exchange gauze roll for a new one.
清󰧖装置卷󱮍卷尽
清󰧖装置卷󱮍已全部卷尽。
󲣌更󰀷成新的卷󱮍。
Ea08280 GAUZE ROLLING FINISHED
All gauze has been rolled up.
Please exchange gauze roll for a new one.
清󰧖装置卷󱮍卷尽
清󰧖装置卷󱮍已全部卷尽。
󲣌更󰀷成新的卷󱮍。
Ea08281 LACK OF SOLVENT
Cleaner solvent is low.
Refill it.
洗󰧖余量󳇮󲣄
清󰧖装置的洗󰧖余量已不足。
󲣌󲔺充洗󰧖。
Ea08282 CLEANING INTERVAL END
Specified number of Board for cleaning interval is
finished.
Cleaning will start.
Please remove the Board on the conveyor.
清󰧖󳋉隔󱮨束
已󱮤完成了清󰧖󳋉隔所指定枚数的基板印刷。
始施清󰧖作。
󲣌取出送上的基板。
Ea08283 CLEANER EXHAUST VALVE CLOSE ERROR
Failed to close the exhaust valve for the cleaner.
清󰧖装置吸引排气󳋕作(󳋂)不良
不能󳋂清󰧖装置吸引排气󳋕。
Ea08284 CLEANER EXHAUST VALVE OPEN ERROR
Failed to open the exhaust valve for the cleaner.
清󰧖装置吸引排气󳋕作()不良
不能打清󰧖装置吸引排气󳋕。
Ea08285 GAUZE ROLL MOTOR ALARM
Control board of gauze rollmotor detected error.
卷󱮍卷󳝁达异常󰖕出。
卷󱮍卷󳝁达控制基板󰖕出了异常。
Ea08288 CLEANER VACUUM UP CHECK ERROR
The vacuum of the cleaner was not up when the cleaner head goes up.
Possible cause:
1. The cleaner hose has damage.
2. The cleaner filter is choked up.
3. The exhaust valve is broken.
4. The blower motor is broken.
清󰧖真空上升󰖕󰒺󳇮󲣄
清󰧖上升󰋋，清󰧖真空没有上升。
可能是因下列原因所致:
1. 吸附管等的破󰀴
2. 󲲜󰮹器的网眼堵塞
3. 清󰧖装置吸引排气󳋕的作不良
4. 鼓󳖣󳝁达的作不良
Ea08289 CLEANER VACUUM DOWN CHECK ERROR
The vacuum of the cleaner was not down when the cleaner head goes down.
Possible cause:
1. The exhaust valve is broken.
清󰧖真空下降󰖕󰒺󳇮󲣄
清󰧖下降󰋋，清󰧖真空没有下降。
可能是因下列原因所致:
1. 清󰧖装置吸引排气󳋕的作不良
Ea08290 SOLVENT CEHECK ERROR
The solvent of the cleaner did not reach the cleaner head.
Possible cause:
1. A solvent hose has a crack and the solvent has leaked.
2. There is some garbage in the solvent pump, the solvent do not flow.
3. Lack of solvent.
清󰧖溶到达󳇮󲣄
清󰧖溶没有到达清󰧖部。
可能是因下列原因所致:
1. 因溶管有󳱴裂，使溶泄漏
2. 因溶管中有󰤶物等堵塞，使溶不能流
3. 溶用完
Ea08300 MASK CAMERA LIGHT UP ERROR
Failed to move mask camera light up.
网板相机照明上升󳇮󲣄
网板相机照明不上升。
Ea08301 MASK CAMERA LIGHT UP ERROR 网板相机照明下降󳇮󲣄