YAMAHA 报警资料.pdf - 第46页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 46 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 45 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please press [ERROR CLEAR] button. 点[清除]按。
Ea00948 SIDE VIEW CAMERA BRING BACK RETRY CHECK
Bring back parts error happened on this board.
But it selected skip mounting this parts.
May I continue Auto Running?
[YES] Running start and the board is transported.
[NO] Reset and check the board condition.
完成装的基板确
基板因装状不定生了，
但元件的装已置跳。
运行?
[是] 始运行，入基板。
[否] 行位，确基板。
Ea00949 MOUNTING CONDTION CHECK IS CANCELED
Mounting condition check is canceled.
Setting about retry of error component is disabled.
Press [OK] button and start running then the machine will continue Auto Running.
取消弃元件
在弃元件的途中，操作人出了中止作的指令。
取消弃元件。
在画面点[OK]并按[START]按，取消元件的
装状，并始装。
Ea00950 SIDEVIEW TIMEOUT ERROR
The Application error occurred by sideview action.
datail number
Please stop this action, and retry.
If this error occurred many times, please execute the following.
Trouble of application
- extecute of Parts Adjust - Test.
- none is set to Machine Setting - Side view camera,
and reload board data.
面相机超
在面相机理中生了用件。
datail number
中止理，重新行。
如果反示画面，按照下列指示操作。
·行元件整 - 。
·将机器置 - 工厂置 - 面相机置「没有」。
置完后，重新入基板程序。
Ea00951 SIDE VIEW CAMERA PARTS REVERSE OVER ERROR
Parts are reversing.
Please check the parts and the sequence unit.
MountData
PartsData
Name
Feeder Pos
Pallet Pos
Table/Head
面相机 元件翻
元件正反面反了。
确元件以及元件供装置的状。
装数据 号
元件数据 号
名称
送料器安装位置 号
料架抽出位置 号
工作台/Head 号
Ea00952 SIDE VIEW CAMERA PARTS SIZE ERROR
The shape sizes of parts are outside ranges.
Please check the parts and the component information.
MountData
PartsData
Name
Feeder Pos
Pallet Pos
Table/Head
面相机 元件尺寸
面相机的元件形状尺寸在范外。
确元件以及基板程序的元件信息。
装数据 号
元件数据 号
名称
送料器安装位置 号
料架抽出位置 号
工作台/Head 号
Ea00970 BOARD FILE READ ERROR
It failed in reading the board data.
Cause:
The mount information data is broken.
There is a possibility that the mount data file has been damaged.
Measures:
If you have a backup data, delete the broken data, copy from the backup,
and reload the data.
If you don't, delete the broken data and create new data.
基板程序入
基板程序的入失。
原因:
基板程序的装信息文件的数据异常。
文件有可能破。
策:
如果有基板程序的份，除异常的基板、
将份的制，然后重新入。
如果没有基板程序的份,除异常的基板后，
在新建。
Ea00971 BOARD FILE READ ERROR
It failed in reading the board data.
Cause:
The parts information data and parts data base is broken.
There is a possibility that the mount data file has been damaged.
Measures:
If you have a backup data, delete the broken data, copy from the backup,
and reload the data.
If you don't, delete the broken data and create new data.
If it failed in reading the database, restore the database file from
database backup or system backup.
基板程序入
基板程序入失。
原因:
基板程序的元件信息文件或元件数据的数据异常。
文件有可能破。
策:
如果有基板程序的份，除异常的基板、
将份的制，然后重新入。
如果没有基板程序的份,除异常的基板后，
在新建。
如果入数据失，使用数据的原程序份,
原数据。
Ea00972 BOARD FILE READ ERROR
It failed in reading the board data.
Cause:
The mark information data and mark data base is broken.
There is a possibility that the mount data file has been damaged.
Measures:
If you have a backup data, delete the broken data, copy from the backup,
and reload the data.
If you don't, delete the broken data and create new data.
If it failed in reading the database, restore the database file from
database backup or system backup.
基板程序入__
基板程序入失
原因:
基板程序的信息文件或数据的数据异常。
文件有可能破。
策:
如果有基板程序的份，除异常的基板、
将份的制，然后重新入。
如果没有基板程序的份,除异常的基板后，
在新建。
如果入数据失，用数据的原程序份,
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 46 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
原数据。
Ea00973 BOARD FILE READ ERROR
It failed in reading the machine setting data.
Cause:
The machine configuration data file is broken.
There is a possibility that the mount data file has been damaged.
Measures:
Please restore the machine data.
基板程序入
机器置数据文件的入失。
原因:
机器置文件内的数据异常。
文件有可能破。
策:
使用程序份、原机器数据。
Ea00980 BOARD FILE READ ERROR
It failed in reading the machine setting data.
Cause:
The machine configuration data file is broken.
There is a possibility that the mount data file has been damaged.
Measures:
Please restore the machine data.
基板程序入
机器置数据文件的入失。
原因:
机器置文件内的数据异常。
文件有可能破。
策:
使用程序份、原机器数据。
Ea00989 HEAD SPEC SETTING ERROR
Some heads use a "fixed nozzle" that is not defined
in Head spec information.
Head 格信息置
在 Head 格信息中不可安装的吸嘴
被当作固定吸嘴行了登。
Ea00992 WAFER NOZZLE SPEC FILE READ ERROR
Fail to read the wafer nozzle spec information file.
晶片吸嘴格信息文件的入
晶片吸嘴格信息文件的入已失。
Ea00993 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check as followings:
-Some nozzles are on the blow unit?
-The sensor detects something but nozzles?
-The sensor is broken?
In case of YG200, please check the front unit sensor.
吸嘴吸嘴排气装置的吸嘴感器正在感。
确下列目。
-排气装置上是否存在吸嘴。
-感器是否被障碍物遮断。
-感器是否生故障。
YG200 ，前排气装置。
Ea00994 INTERLOCK ERROR
Nozzle detecting sensor on the shaft blow unit detects something.
Please check as followings:
-Some nozzles are on the blow unit?
-The sensor detects something but nozzles?
-The sensor is broken?
-The setting in VmSpec is right?
[Setting]-[Installation Setting]-[Cleanng Blow Unit]
In case of YG200, please check the rear unit sensor.
吸嘴吸嘴排气装置的吸嘴出感器正在感。
确下列目。
-排气装置上是否存在吸嘴?
-感器是否被障碍物遮断?
-感器是否生故障?
-机器置是否符合机器格?
[机器置]-[工厂置]-[吸嘴清排气装置]
YG200 ，后排气装置。
Ea00997 INTERLOCK ERROR
The component may hit neighbor head.
Move the Z axis until error message disappears.
可能与相吸嘴干。
将 Z 移至安全位置。
Ea00999 RETRY active. 正在行重新行。
Ea01023 WARNING: NOT ENOUGH HDD SPACE
Free space on Hard Disk is less
than 10MB. To avoid the possibility
that you cannot save new data anymore
and that data might be lost, it is best
to create new space on the hard disk now.
Copy unused Board data to floppy disks
and delete it from the hard disk.
警告: 硬空不足
硬可用空不足 10MB。
如运行，可能程序会受。
先将基板程序份在上，再将硬上的程序除。
Ea01048 NOZZLE CONDITION ERROR
As a result of vision recognition, the following nozzle
is concluded dirty.
Before auto-running, clean the nozzle, and then execute
this command.
And please check if the tip of the nozzle is broken.
HEAD
吸嘴状
的果，吸嘴有垢。
在始生之前，清吸嘴。
清后，重新确吸嘴的状。
或者，确吸嘴前端是否坏。
装号
Ea01049 VICS TIMEOUT ERROR
The waiting routine for VICS was interrupted by
time-out error.
VICS 超
已中止了系的理等待。
Ea01050 NOZZLE CONDITION CHECK
It finished correctly
and couldn't find trouble on NOZZLES.
吸嘴状确正常束
没有吸嘴异常。
Ea01052 NOZZLE CONDITION ERROR (MOUNT HEAD)
As a result of vision recognition, the following mount
nozzle is concluded dirty.
Before auto-running, clean the nozzle, and then execute
this command.
If the head brings back a component, please reset running
and check the nozzle condition, mount height, valve con-
dition etc.
TABLE
HEAD
吸嘴状(行装的装)
的果施装的吸嘴有垢。
如吸嘴有垢，在生始前行吸嘴清，
并重新确吸嘴的状。
此外，也可能是因元件被回而引起的。
此，立即自运行行位，并确
吸嘴、装高度，状等。
工作台号
Head 号
Ea01053 NOZZLE CONDITION ERROR (DUMP HEAD) 吸嘴状(行弃的装)
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 47 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
As a result of vision recognition, the following dump
nozzle is concluded dirty.
Before auto-running, clean the nozzle, and then execute
this command.
If the head bring backs a component, please reset running
and check the nozzle condition, mount height, valve con-
dition etc.
TABLE
HEAD
的果，施弃的装的吸嘴有垢。
如吸嘴有垢，在生始前清吸嘴，并重新
确吸嘴的状。
此外，也可能是因元件被回而引起的。
此，立即自运行行位，并确吸嘴、
装高度、状等。
工作台号
Head 号
Ea01222 ASCII data analyzing error. The following error occurred.
2:Mark Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
2:信息
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01223 ASCII data analyzing error.The following error occurred.
3:Board Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
3:基板信息
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01231 ASCII data analyzing error.The following error occurred.
1:Pre Disp.Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
1:点胶信息
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01232 ASCII data analyzing error.The following error occurred.
2:Dot Disp.Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
2:正式点胶信息
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01233 ASCII data analyzing error.The following error occurred.
3:Unknown
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
3．不明
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01234 ASCII data analyzing error.The following error occurred.
4:Unknown
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
4．不明
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01235 ASCII data analyzing error.The following error occurred.
5:Local Fidu.Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
5:局部基准信息
按指定取得的字符串中有空白存在，生。
足指定条件的数据完全不存在，也会生。
Ea01236 ASCII data analyzing error.The following error occurred.
6:Mount Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
6:装信息
根据指定取得的字符串存在空白，将生。
足指定条件的数据完全不存在，也将生。
Ea01237 ASCII data analyzing error.The following error occurred.
7:Board Origin
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
7:基板原点
根据指定取得的字符串存在空白，将生。
足指定条件的数据完全不存在，也将生。
Ea01238 ASCII data analyzing error.The following error occurred.
8:Blk Repeat Info.
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
8: 拼制信息
根据指定取得的字符串存在空白，将生。
足指定条件的数据完全不存在，也将生。
Ea01239 ASCII data analyzing error.The following error occurred.
9:Board Size
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
9:基板外形尺寸
根据指定取得的字符串存在空白，将生。
足指定条件的数据完全不存在，也将生。
Ea01240 ASCII data analyzing error.The following error occurred.
10:Board Fiducial
This error occurs when:
- the search criteria set returns empty strings.
- No data matching the search keyword was found.
ASCII 数据 解析。在下列中生了。
10:基板基准
根据指定取得的字符串存在空白，将生。
足指定条件的数据完全不存在，也将生。
Ea01241 ASCII data analyzing error.The following error occurred.
11:BLOCK Fiducial
This error occurs when:
ASCII 数据 解析。在下列中生了。
11:拼基准
根据指定取得的字符串存在空白，将生。