YAMAHA 报警资料.pdf - 第228页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 228 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 227 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
and restart the production.
Ea29071 Ext. tray changer Pallet set error
The head of the machine is picking a component.
If "SET PALLET" is executed, component will drop from head.
Remove component from head and execute "SET PALLET" again.
外部托交器 料架抽出
机器的 Head 正在吸附元件。
行料架抽出，可能致元件掉落。
取出吸附状的元件，并再次行。
Ea29072 Ext. tray changer Pallet set error
The head of the Ext. tray changer is picking a component.
If "SET PALLET" is executed, component will drop from head.
Remove component from head and execute "SET PALLET" again.
外部托交器 料架抽出
外部托交器的 Head 正在吸附着元件。
行料架抽出，可能致元件掉落。
取出吸附状的元件，并再次行。
Ea29073 Ext. tray changer Pallet set error
Cannot set the designated pallet, because the magazine is not set.
Please check whether the magazine of designated pallet is set correctly.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Magazine No.
Pallet No.
Magazine set sensor: Undetect magazine
外部托交器 料架抽出
因没有安装收柜，所以不能抽出指定的料架。
确指定料架的收柜是否已正确置，
收柜安装感器是否正常感。
料架台号 号
收柜号 号
料架号 号
收柜安装感器 未出收柜
Ea29074 Ext. tray changer Pallet set error
Cannot set the designated pallet, because the magazine is not set.
Please check whether the magazine of designated pallet is set correctly.
And please check whether the Pallet Close sensor points to correct position.
Stage No.
Magazine No.
Pallet No.
Magazine set sensor: Undetect magazine
外部托交器 料架抽出
因没有安装收柜，所以不能抽出指定的料架。
确指定料架的收柜是否已正确置，
收柜安装感器是否正常感。
料架台号 号
收柜号 号
料架号 号
收柜安装感器 未出收柜
Ea29075 Auto tray changer Dump only pallet set error
There is no designated pallet.
Please check whether the pallet and the magazine are set correctly.
Pallet
自托交器 弃用料架安装
不存在所指定的弃用料架。
确料架以及收柜是否安装正确。
安装料架后，重新始自运行。
料架号 号
Ea29076 Auto Tray Failed to return pallet
Returning pallet was failed for pallet close sensor non-detection.
There is danger of pallet crash in this state.
Please be sure to do the following operation.
1. Confirm whether there is no pallet on the pallet stage.
2. Remove by the hand when a pallet exists on the pallet stage.
Stage No.
Pallet No.
自托料架退回失
料架退回失。料架退回用感器不感。
如持此状，料架有碰撞的危，
所以必按照以下位。
1. 确料架是否从收柜出。
2. 如有料架出，用手推回收柜。
料架台号 号
料架号 号
Ea29080 Auto tray changer Component empty
Component counter reached specified number.
Refill the components and run again.
Component data Name
Start Pallet No.
End Pallet No. [CNTcmp_inf5]
自托交器 元件用完
使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号 名称
料架始号 号
料架束号 [CNTcmp_inf5]号
Ea29081 Ext. tray changer Component empty
Component counter reached specified number.
Refill the components and run again.
Component data Name
Start Pallet No.
End Pallet No. [CNTcmp_inf5]
外部托交器 元件用完
使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号 名称
料架始号 号
料架束号 [CNTcmp_inf5]号
Ea29082 Auto tray changer Component empty
All components in alternative loop are not available.
This can be caused by the followings:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Start Pallet No.
End Pallet No.
自托交器 元件用完
替代元件循的全部元件不可使用的状。
原因如下：
- 生了吸附或。
- 使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29083 Ext. tray changer Component empty
All components in alternative loop are not available.
This can be caused by the followings:
- Pick up or recognition error happened.
- Component counter reached specified number.
Refill the components or check trays and run again.
Component data
Start Pallet No.
End Pallet No.
外部托交器 元件用完
替代元件循的全部元件不可使用的状。
原因如下：
- 生了吸附或。
- 使用元件数已达到定数目。
充下列元件后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29084 Auto tray changer Components empty
All components in alternative loop are not available.
This can be caused by the followings:
- Door of auto tray changer was opened.
自托交器 元件用完
因柜敞或元件用完等原因，
不能使用下列元件。
柜或充元件后，重新始运行。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 228 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
- All components were empty.
Close the door or supply components and run again.
Component data
Start Pallet No.
End Pallet No.
元件数据 号
料架始号 号
料架束号 号
Ea29085 Ext. tray changer Door opening error
Cannot use the following component because the door is open.
Please close the door and restart production.
Component data
Start Pallet No.
End Pallet No.
外部托交器 柜打
因柜敞着，所以下列元件不能使用。
在柜后，重新始运行。
元件数据 号
料架始号 号
料架束号 号
Ea29086 Auto tray changer Components empty
All the tray for the parts are not available.
This can be caused by the followings:
- All the tray is empty.
- Tray changer door is open.
Please supply parts or close the door and
start auto-running again.
Parts No. Name
Start Pallet No.
End Pallet No.
自托交器 元件用完
由柜敞或元件用完等原因，
不能使用下列元件。
柜或充元件后，重新始运行。
元件数据 号 名称
料架始号 [PLTcmp_inf4]号
料架束号 [PLTcmp_inf5]号
Ea29087 Ext. tray changer Component empty
Cannot use the following component because the component is empty.
Please supply the component and restart production.
Parts No. Name
Start Pallet No.
End Pallet No.
外部托交器 元件用完
因元件已用完，所以不能使用下列元件。
在充元件后，重新始运行。
元件数据 号 名称
料架始号 [PLTcmp_inf4]号
料架束号 [PLTcmp_inf5]号
Ea29088 Auto tray changer Confirmation of special dump back
A component will be dumped back to the tray.
If you already supply component in the tray changer,
Be sure to press "EMERGENCY STOP", remove the component from the head,
and run again.
Component data Name
自托交器 供装置作确
按照特殊返理的置，将元件返回到托。
因生托数停止，所以可能已向
托供装置充了元件。
如已充了元件，可能会造成元件的重叠放置，
所以按急停机按，将元件从 Head 上取出后，
再重新始运行。
元件数据 号 名称
Ea29089 Auto tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
自托元件用完停机
以下托元件呈空的状。
充元件后、按指示器按。
元件名称 注
料架始号 号
料架束号 号
Ea29090 Ext. tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
外部托元件用完停机
以下托元件呈空的状。
充元件后、按指示器按。
元件名称 注
料架始号 号
料架束号 号
Ea29100 Auto tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
自托交器 料架抽出
抓手未能正常作。
注意下列目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收柜没有正常安装
5. 收的收柜柜敞着
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29101 Ext. tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托交器 料架抽出
抓手未能正常作。
注意下列目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收柜没有正常收
5. 收的收柜的柜敞着
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29102 Auto tray changer Hook action error
Failed to start the Hook Action.
自托交器 抓手作
抓手未能正常作。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 229 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
注意下列目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29103 Ext. tray changer Hook action error
Failed to start the Hook Action.
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托交器 抓手作
抓手未能正常作。
注意下列目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收柜抽出，按照如下行理。
1. 按急停机
2. 取出料架
3. 将料架放入收柜
Ea29104 Auto tray changer : Failed to pull out the pallet
Cannot set the designated pallet, because the Hook Pallet sensor doesn't detect
pallet.
Please check whether the designated pallet is set correctly.
And please check whether the Hook Pallet sensor does work correctly.
Stage No.
Pallet No.
Hook Pallet sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托交器 料架抽出
因抓手的料架出感器没有感，所以不能
置指定的料架。
确是否正确置了指定的料架。
另外，确抓手的料架出感器是否正确感。
料架台号 号
料架号 号
抓手料架存在感器:未出 (ATS )
*当前的感器状,可在[装置]-[自托]或[I/O]画面确。
Ea29105 ATS hook action error
The hook doesn't move normally.
Please check whether something is detected on stage set position sensor.
自托交器 抓手作
抓手没有正常作
确料架台安装位置感器是否有什反。
Ea29106 Ext. tray changer Sensor mismatch
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ext. tray changer Sensor mismatch___
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ea29110 Auto tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
自托交器 状
未能正常作。
可能由如下原因所造成的。
确及托交器的状。
1. 没有正常作
2. 感器做出了的判断
Ea29111 Ext. tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
外部托交器 状
未能正常作。
可能由如下原因所造成的。
确及托交器的状。
1. 没有正常作
2. 感器做出了的判断
Ea29120 Auto tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
自托交器 收柜固
因没有安装收柜固定，所以托交器不能作。
打柜并确收柜固定的状。
Ea29121 Ext. tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托交器 收柜固
因没有安装收柜固定，所以托交器不能作。
打柜并确收柜固定的状。
料架台号 号
收柜号 号
Ea29122 Ext. tray changer Magazine clamp error
The magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托交器 收柜固
因没有安装收柜固定，安装收柜固定。
料架台号 号
收柜号 号
Ea29130 Auto tray changer : Pallet protrudes from magazine
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托交器 料架出
料架从收柜中出。
按急停机按，并用手将料架放回到收柜。
工作台号 号
收柜号 号
料架出感器:出 (ATS )
*当前的感器状,可在[装置]-[自托]或[I/O]画面确。
Ea29131 Ext. tray changer Pallet protrude error
The pallet is out of the Ext.Tray magazine.
Please press the "EMERGENCY STOP"
外部托交器 料架出
料架从收柜中出。
按急停机按，并用手将料架放回到收柜。