YAMAHA 报警资料.pdf - 第18页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 18 / 237 Copyright (C) 2009 Y amaha Motor Co., Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 17 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
available for the dot dispense data.
Dot Dispense Data
Local Badmark data
Mark data
正式点胶数据 号
局部坏板数据 号
数据 号
Ea00276 BOARD DATA ERROR
No local badmark data is set to "Note"
for executable dot dispense data.
During production, "Note" data is ignored.
If you want to use local badmark function,
set this " Exec".
If not, set "0" for BadMk in dot dispensing data.
Dot Dispense Data
Local Badmark Data
基板程序
正式点胶信息中的局部坏板"参考"状。
如果"参考"状，机器自运行将被完全忽略，
如要使用，置"行"，
如不使用，在正式点胶信息的坏板中入"0"。
正式点胶数据 号
局部坏板数据 号
Ea00277 4-Point Fiducial Data Error
Dot Dispense Data No.
Fiducial Data No.
It is impossible to use this Fiducial number
which is selected in the Dot Dispense Data,
because this data is [4Local-S].
Please use [4Local-M] Fiducial for 4-point
fiducial.
4 点基准.数据
正式点胶数据号 号
基准数据号 号
因正式点胶数据所指定的基准号[4 局部次]，
所以不能使用。
置 4 点基准的[4 局部主]的基准号。
Ea00278 BOARD DATA ERROR
Dot Dispense Data No.
Fiducial data No.
It is impossible to use this fiducial data,
because this data is [Note].
Please change from [Note] to [Exec].
基板程序
与正式点胶数据的基准数据[参考]状。
正式点胶数据 号
基准数据 号
将置修改
[参考] ---> [行]。
Ea00280 BOARD DATA ERROR
No mark data available for the dot dispense
local fiducial.
Dot Dispense data
Fiducial data
基板程序
不存在正式点胶数据的基准数据。
正式点胶数据
基准数据
Ea00282 BOARD DATA ERROR
Pre dispensing position is outside moving area.
Pre Dispense data
Axes
基板程序
点胶位置在作范以外。
点胶数据 号
名称
Ea00283 BOARD DATA ERROR
There is no dispense head for pre dispensing.
Pre Dispense data
Head number
基板程序
行点胶的点胶不存在。
点胶数据 号
点胶号 号
Ea00284 BOARD DATA ERROR
It is impossible to use "Point Fiducial" for Dispense.
Please check the dot dispense data or fiducial mark
data.
Dot Dispense data
Fiducial data
基板程序
点胶不能使用点基准。
修改正式点胶数据或基准数据。
正式点胶数据 号
基准数据 号
Ea00285 BOARD DATA ERROR
Illegal unit for pre dispensing.
Defined unit for that head is out of range
for adequate unit.
Max unit is 999 including the unit rate.
Pre Dispense data
Head number
Unit
基板程序
指定的点胶所指定使用的胶液量不适当。
修改点胶数据。
胶液量的最大(考系数) 999。
点胶数据 号
点胶号 号
胶液量
Ea00286 BOARD DATA ERROR
Illegal unit for dot dispensing.
Defined unit for that head is out of range
for adequate unit.
Dot Dispense data
Head number
Unit
基板程序
指定的点胶所指定使用的胶液量不适当。
修改正式点胶数据。
正式点胶数据 号
点胶号 号
胶液量
Ea00288 DOT STATION MAX MATRIX NUMBER ERR
Please set max matrix number to more than 1.
Please check the max matrix number.
打点站矩个数
打点矩个数必超 1。
修改打点矩个数。
Ea00289 DOT STATION DATA ERR
All dispense heads can not be able to reach to dot
station.
Please check the dot station position X,Y and Z.
Head number
Axis
打点站数据
点胶不能到达打点站。
修改打点站点的坐 X、Y。
点胶号 号
名称
Ea00291 COMPONENT DATA ERROR
In case using alternative components for tray,
元件数据
使用托元件的替代元件，
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 18 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
it is impossible to use "Sp.Dump Back" for [Dump Way].
CMP No.(with alternative component)
Name
CMP No.(with "Sp.Dump Back")
Name
不能使用[特殊返理]。
替代元件指定元件号 名称
特殊返指定元件号 名称
Ea00293 COMPONENT DATA ERROR
[BGA ball data]file for this component does not exist.
This component needs [BGA ball data] file.
Component Name
Please make [BGA ball data] file.
元件数据
与元件数据的[BGA 球引脚信息]文件不存在。
元件必需使用[BGA 球引脚信息]文件。
元件名称
建[BGA 球引脚信息]数据。
Ea00295 DATA LOAD ERROR
Failed to load [BGA ball data].
Component data Name
In Draw Shape button of Adjust window, please
confirm [BGA ball data] file.
数据入
[BGA 球引脚信息]文件的入失了。
元件数据 号 名称
在助整的[定形状示]中，
确[BGA 球引脚信息]数据。
Ea00296 BOARD DATA ERROR
Setting of [Alignment Type] is [Undefined].
Please set [Alignment Type].
Component data Name
基板程序
[校正型][未置]。
置[校正型]。
元件数据 号 名称
Ea00297 BOARD DATA ERROR
Ext.TC or AutoTC is not available on
this machine.
Mount data
Component data Name
基板程序
因没有配置外部托交器或自托交器，
所以不能使用。
装数据 号
元件数据 号 名称
Ea00298 BOARD DATA ERROR
There is no dispense sequence for dot dispensing.
Check the head and unit
in 2-1-[Dot Disp. Info].
Dot Dispense data
基板程序
行正式点胶的作流程不存在。
在正式点胶画面确点胶和胶液量。
正式点胶数据 号
Ea00299 BOARD DATA ERROR
There is no dispense sequence for pre dispensing.
Check the head and unit
in 2-1-[Pre Disp. Info].
Pre Dispense data
基板程序
行点胶的作流程不存在。
在点胶画面确点胶和胶液量。
点胶数据 号
Ea00300 Tray unit error : The component is not placed
correctly on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
托交器∶没有将供元件正确放置在料站上。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00301 Tray unit error : Returned component is not placed
correctly on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 未能将返回的元件正确放置在料站上。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
Ea00302 Tray unit error : Failed to pick the component from
the tray.
The tray unit could not pick
from the following tray position:
Remove component from head.
Mount data
Component data Name
Pallet
Next tray position is for the next pick sequence.
(X= , Y= )
托交器: 未能从托上吸附元件。
如果托上有元件存在，取出。
如果有吸附状的元件，取出。
装数据 号
元件数据 号 名称
料架
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00303 Tray unit error : Failed to put the component
on the traverser station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
托交器: 未能将元件正确放置在料站上。
如果料站上有元件，取出。
装数据 号
元件数据 号 名称
料站
接着使用的元件托上
(X= ， Y= )
位置的元件。
Ea00304 Tray unit error : Failed to pick the component from
the traverser station.
If component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 未能从料站上吸附元件。
如果料站上有元件存在，取出。
装数据 号
元件数据 号 名称
料站
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 19 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea00305 Tray unit error : Unknown component is
on the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
托交器: 料站上放置了元件。
取出元件。
装数据 号
元件数据 号 名称
料站
Ea00306 Tray unit error : Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架退回收柜。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00307 Tray unit error : Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
Mount data
Component data Name
Pallet
托交器: 未能将料架从收柜中抽出。
重新始生，将料架退回收柜。
装数据 号
元件数据 号 名称
料架
Ea00308 Tray unit error : Failed to start the Hook Action.
Please check the following items:
1. Pallet (No. ) access position.
2. The hook nail.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open..
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP" ON.
2. Remove the pallet from the stage section.
3. Return the pallet to its magazine.
托交器: 抓手未能正常作。
注意以下的目。
1．重新将料架(No. )放置在正确位置。
2．抓手的爪弯曲。
3．抓手感器的作不良。
4．收柜不能正常行收。
5．收的收柜柜敞状。
如料架出了收柜，按下列操作。
1．按下急停机按。
2．取出料架。
3．将料架放回收柜。
Ea00310 Tray unit : The tray unit head or traverser station
has a component attached to its nozzle (pad).
Please remove the component.
托交器: 外部托的 Head 或外部托
料站上存在元件，取出。
Ea00311 Tray unit error: Abort the RESET process.
If a pallet is out of the magazine, please remove it
and store it to its assigned magazine by hand.
托交器
因急停机，料架抽出作中断了。
Ea00313 Tray unit error: The pallet is out of the magazine.
Return the pallet to its assigned magazine.
托交器: 料架出了收柜。
将料架退回收柜。
Ea00314 Tray unit error: The door is open.
Please close the door.
托交器:柜敞着。
敞的柜。
Ea00315 Tray unit error: Failed to store the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能将料架退回收柜。
将料架退回收柜。
Ea00316 Tray unit error: Failed to pull out the pallet.
To start production again, please return the pallet
to its assigned magazine.
托交器: 没能从收柜中抽出料架。
将料架退回收柜。
Ea00317 TRAY CHANGER ERROR : The door is open.
The door is open or the Z-axis is servo-off.
Please close the door.
(When the door light is off in spite of the door switch 'close',
please make the door switch into 'open' once and make it 'close'.)
托交器 : 柜敞着。
柜敞着，或托交器的 Z 的伺服着。
敞着的柜。
(然柜[]，但柜指示灯不亮灯，
先将柜置[]，然后再置[]。)
Ea00318 Tray unit error : Failed to pick up components from
the traverser station.
If a component is on the station, please remove it.
Mount data
Component data Name
Station
If this error exist many times, please confirm following,
1.[YTF] Vacuum sensor of the traverser station
2.[SMT] Vacuum valve of the head
3.[TrayChanger] Z-axis
托交器:未能从料站吸附元件。
取出元件。
装数据 号
元件数据 号 名称
料站
如生，下列目。
1．[YTF] 料站的真空感器
2．[片机] 装的吸附
3．[托交器] 料站 Z 坐
Ea00330 The head of the machine or tray-changer is picking a
component. If "SET PALLET" is executed,
component will drop from head.
Remove component from head and execute "SET PALLET"
again.
机器或者托交器呈元件吸附状。
如果此抽出料架，元件可能会脱落。
取出吸附状的元件，并再次行。
Ea00331 TRAY CHANGER ERROR
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
托交器
因托交器陷于了危状或没有料到的状，所以不能重新始运行。
如料架从收柜中出，按下列恢原状。
1. 按急停机按
2. 用手取出料架
3. 按 READY 按
4. 打柜，将料架放回原位