YAMAHA 报警资料.pdf - 第110页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 1 10 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chines…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 109 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
cancel command.
Measure Nozzle was not save data.
不行吸嘴形状数据的保存。
Ea07536 It failed to measure the nozzle shape.
On the recognition of Side view camera, it happened nozzle fit error
at %d head
(Detail error: %d[%s] Nozzle: %s)
The nozzle tip position is detected as illegal value.
Please stop running, and confirm that the head handle the nozzle
correctly.
吸嘴形状的失了。
用面相机量%d 号装的吸嘴前端形状，
生了吸嘴配合。
(: %d[%s] 吸嘴: %s)
吸嘴前端或特征部的位置超了容。
吸嘴的安装可能不正确，
停止运行，吸嘴的安装状况。
Ea07537 It failed to measure the nozzle shape.
The nozzle of number %d head was not able to
be recognized by side-view camera.
(Detail error: %d[%s] Nozzle: %s)
Please confirm the following.
1. Is the nozzle correctly installed?
2. Does the side view lighting light?
Please record head number and detail error,
and contact the maker when this error occurs many times.
吸嘴形状的失了。
用面相机%d 号装的吸嘴，失了。
(: %d[%s] 吸嘴: %s)
确下列目。
1. 吸嘴的安装是否正确?
2. 面照明是否呈亮灯状?
如反生，
Head 号和号，向生厂商咨。
Ea07538 WATCH DOG - HEAD & FEEDER STATUS INCONSISTENT Head 的下降状和送料器的器状不一致
Ea07539 SHUFT CLEANING BLOW EXECUTION ERROR
Can't execute shuft cleaning blow of manual or fixed
nozzle.Please reload 'board data' and retry.
Execution condition
1. Not editing of 'board data'.
2. The error must not occur by data check of
the 'board data'.
吸嘴吸嘴排气清行
不能行固定/手更吸嘴的吸嘴排气清。
重新入基板程序后，重新行。
行条件:
1. 基板程序不能状。
2. 基板程序的程序中不能生。
Ea07540 NOZZLE CONDITION ALL CHECK RESULT
<<< WARNING >>>
After the error is cleared, the check result list is displayed.
Please clean the NG nozzle of the result before producing it.
Please confirm the state of the nozzle again after cleaning it.
And please check if the tip of the nozzle is broken.
吸嘴状全部果
<<< 警告 >>>
解除后示果列表。
生前、清果 NG 的吸嘴。
清后、再次确吸嘴的状。
并、确吸嘴的前端是否破。
Ea07541 VACUUM LEVEL ALL CHECK RESULT
<<< WARNING >>>
Detected Illegal Vacuum Level.
After the error is cleared, the check result list is displayed.
Please check the nozzle of NG as shown in the following content.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
真空全部果
<<< 警告 >>>
出异常
解除后示果列表。
生前、 果 NG 的吸嘴的以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07544 SHAFT CLEANING BLOW ALL CHECK RESULT
<<< WARNING >>>
Detected Illegal Vacuum Level.
After the error is cleared, the check result list is displayed.
Please check the nozzle of NG as shown in the following content.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
吸嘴排气全部果
<<< 警告 >>>
出异常。
解除后示果列表。
生前、 果 NG 的吸嘴的以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07545 SHAFT CLEANING BLOW ERROR
<<< WARNING >>>
Detected Illegal Vacuum Level.
TABLE
NOZZLE
HEAD
Investigate the following item.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
吸嘴排气
<<< 警告 >>>
出异常。
工作台号
吸嘴
Head
确以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07546 "ALARM: BASE FAN IS ABNORMAL"
The Base FAN of Machine is not working.
When Machine is kept running, will be cause trouble of Machine.
Please consult your distributor for further information
with FAN number.
FAN number:
片机散扇异常
出了片机的扇异常。
运行、会引作。
下列号后、与制造厂商系。
扇号:
Ea07548 ALARM: BASE FAN IS ABNORMAL
The Base FAN of Printer is not working.
When Machine is kept running, will be cause trouble of Printer.
Please consult your distributor for further information
with FAN number.
FAN number:
印刷机排扇异常
出了印刷机的扇异常。
运行，会引作。
下列号，与制造厂商系。
扇号:
Ea07702 CAMERA LIGHT START ERROR
Camera light can't be started.
相机照明启
相机照明的启失了。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 110 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please reboot the machine after clearing the error. 清除提示后，重新启机器。
Ea07800 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
The OPT-FLAG prevents the machine to pick up next
component.
Mount data
Component data Name
Head
存在不可吸附的元件。
OPT-FLAG 出分割吸附、装的指示，
因此下列元件的吸附已被禁止。
装数据 号
元件数据 号 名称
装 号
Ea07801 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
The head is already occupied by another component,
and the indicated picking action is not possible.
Mount data
Component data Name
Head
存在不可吸附的元件。
装已其他元件占有，不能行指定的吸附。
装数据 号
元件数据 号 名称
装 号
Ea07802 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
A picking up group without rotation-action could not
include a mounting data with some rotation.
Mount data
Component data Name
Head
存在不可吸附的元件。
在不旋装的状下行吸附、装的中，
不能加入旋装行装的装数据。
装数据 号
元件数据 号 名称
装 号
Ea07803 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the component on
neighbor nozzle.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，
已判定会与分配到相吸嘴的元件相碰。
装数据 号
元件数据 号 名称
装 号
Ea07804 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
with component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，
已判定会与吸附着元件的相吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07805 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
A picking up group without rotation-action could not
include the FINE type component. Check the data.
Mount data
Component data Name
Head
存在不可吸附的元件。
在不旋装的状下行吸附、装的中
不能加入 FINE 型的元件。
确数据。
装数据 号
元件数据 号 名称
装 号
Ea07806 SOME COMPONENT COULD NOT BE PICKED UP
Because the machine had picked up a component of FINE type,
the machine could not pickup another of FINE type.
Mount data
Component data Name
Head
同一个吸附、装内，包含着数个 FINE 型元件。
必修改数据。
装数据 号
元件数据 号 名称
装 号
Ea07807 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
without component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，已判定，
元件的一会与没有元件的相吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07808 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
without component during the rotating the component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，已判定，
旋元件，会与没有元件的相的吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07809 SOME COMPONENT COULD NOT BE PICKED UP
The machine had tried to pickup components belongs
different blocks.
Mount data
Component data Name
Head
存在不可吸附的元件。
正要在同一吸附、装内跨越多个拼来吸附元件。
装数据 号
元件数据 号 名称
装 号
Ea07810 NO COMPONENT FOR USE
A component is not available at this moment.
Please confirm the component to be ready,
and run again.
Mount data
Component data Name
存在不可使用的元件。
因下列元件已判定元件用完或不可使用，
所以无法使用。
装数据 号
元件数据 号 名称
装 号
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 111 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Head
Ea07811 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
If the head picks up the component, the component might
hit the lighting unit for fiducial mark.
Please confirm the data and run again.
Mount data
Component data Name
Head
存在不可吸附的元件。
用下列装吸附下列元件，已判定移相机照明
会与元件相碰撞。
确数据。
装数据 号
元件数据 号 名称
装 号
Ea07813 NO COMPONENT FOR USE
A component is not available at this moment.
Please confirm the component to be ready,
and run again.
Mount data
Component data Name
Head
存在不可使用的元件。
下列元件已判定元件用完或不可使用，
所以无法使用。
装数据 号
元件数据 号 名称
装 号
Ea07815 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
If the head picks up the component, the component might
hit the multimacs.
Please confirm the data and run again.
Mount data
Component data Name
Head
存在不可吸附的元件。
用下列 Head 吸附下列元件， MultiMACS 与
元件可能相互干。确数据。
装数据 号
元件数据 号 名称
Head 号
Ea07816 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
If the head picks up the component, the component might
hit the lighting unit for sideview.
Please confirm the data and run again.
Mount data
Component data Name
Head
存在不可吸附的元件。
用下列 Head 吸附下列元件，面相机照明
和元件可能相互干。确数据。
装数据 号
元件数据 号 名称
Head 号
Ea07817 SOME COMPONENTS ARE NOT POSSIBLE TO MOUNT
If components were mounted, components will hit
the camera unit for sideview.
Please confirm the data and run again.
Mount data
Component data Name
Head
存在不可装的元件。
用下列元件装，面相机和元件可能相互干。
确数据。
装数据 号
元件数据 号 名称
Head 号
Ea07818 CAUTION:SOME COMPONENTS ARE NOT POSSIBLE TO MOUNT
If components were mounted, components will hit the camera unit
for sideview according to the mount height offset. Please confirm the data.
Mount data
Component data Name
Head
Component height [mm]
Mount height offset [mm]
Max mount height [mm]
警告: 存在不可装的元件。
用下列元件装，因装高度偏移量，
面相机和元件可能相互干。
确数据。
装数据 号
元件数据 号 名称
Head 号
元件高度 [mm]
装高度偏移量 [mm]
可以装的最大高度 [mm]
Ea07870 The reset process has been interrupted.
Please try the RESET command again until it is finished.
已中断位。
重新行，并正确完成位。
Ea07871 CAN NOT EXECUTE COMMAND
Can not execute this command , because RESET is not
finished completely.
Please try the RESET command again, and finish it.
不能行指令
因位没有完成，所以不能行指令。
重新行位。
Ea07876 CAN NOT EXECUTE COMMAND
Failed to execute this command,
because the push-up unit's position is not enough low.
Please execute this command after moving it down again,
指令不能行
因伺服板没有充分下降，
所以不能行指令。
用送装置操作和位使伺服板下降后，
重新行指令。
Ea07911 PALLET IDTAG PART NAME ERROR
Pallet No.
Component Data
ID Tag Data
料架 ID-Tag 元件名称不一致
所抽出的料架的、基板程序的元件信息中
所置的元件名称与从 ID-Tag 取的元件
名称不一致。
料架号 号
元件名称 元件信息
ID-Tag
Ea07912 PALLET IDTAG CONTROLLER ERROR [PARITY]
If you want to stop checking of ID tag,
please set usage of special function of ID tag to OFF.
料架 ID-Tag 控制器通信 垂直奇偶
与 ID-Tag 控制器的通信已失。
中止 ID-Tag 运作，
将 ID-Tag 的特殊格置 OFF。
Ea07913 PALLET IDTAG COMMUNICATION ERROR
If you want to stop checking of ID tag,
please set usage of special function of ID tag to OFF.
料架 ID-Tag 通信
与抽出料架的 ID-Tag 的通信已失。
料架号 号
中止 ID-Tag 运作，