88192277-01-19 - Micron Technical Reference V9 Volume 4.pdf - 第205页

TRANSPORTATION - MAJOR RELOCATION MACHINE SUPPLIES AND EN VIRONMENTAL CONDITIONS Chapter Issue 5, Nov 19 Technical Reference Manual 42.39 And as described in the IPC Standard J-STD-001G-Requirements fo r Soldered Electri…

TRANSPORTATION - MAJOR RELOCATION

MACHINE SUPPLIES AND ENVIRONMENTAL CONDITIONS

42.38 Technical Reference Manual Chapter Issue 5, Nov 19

MACHINE SUPPLIES AND ENVIRONMENTAL CONDITIONS

Operating

Conditions

The printer must only be operated in the following operating envelope:

• Indoors only

• Unsuitable for use in wet locations

• Temperature = 5 to 40°C (40 to 105°F)

• Humidity = Maximum 80% Relative Humidity (non condensing)

• Altitude = Maximum 2,000 metres (6,500 feet)

• Pollution must comply to Degree 2

ASM KVArecommends a power supply capacity of 2.4 or greater.

Electrical

ASM requires additional machine supply protection with the ﬁtment of an external double pole

circuit breaker conforming to national, federal or local legislation. recommends that the

external circuit breaker is ﬁtted near the printer and within easy reach of the operator. Use

the following table to ensure the recommended circuit breaker is used:

ASM

DEK

The machine operates on 115V to 230V ±10% 50/60Hz single phase ac mains.

Pneumatic Supply

The machine requires a pneumatic supply of clean, non lubricated air which should maintain a

minimum pressure of 5 Bar and a maximum of 8 Bar. The printer requires 5 litres/minute for

general use and a maximum of 226 litres/minute at 6 Bar.



The air should be to ISO 8573.1 standard, quality class 2.3.3

NOTE

An over current circuit breaker protects the machine's internal wiring and components from

overheating or catching ﬁre during fault conditions. Under no circumstances must a circuit

breaker of value greater than 20 Amps be ﬁtted.

Transient overvoltages must not exceed those deﬁned in Cat 2 of 60364-4-443.IEC

Voltage ﬂuctuations must not exceed 10% of nominal voltage.

115 Volts

230 Volts

With VF25 Internal

Vacuum Unit

With VF30/35 Internal

Vacuum Unit

Without Internal

Vacuum Unit

230 Volts

Machine Current Consumption (Approx)

Value of Wall Mounted Circuit Breaker

12 Amps

15 Amps

16 Amps

6 Amps

10 Amps

6 Amps

8 Amps

10 Amps

3 Amps

6 Amps

TRANSPORTATION - MAJOR RELOCATION

MACHINE SUPPLIES AND ENVIRONMENTAL CONDITIONS

Chapter Issue 5, Nov 19 Technical Reference Manual 42.39

And as described in the IPC Standard J-STD-001G-Requirements for Soldered

Electrical and Electronic Assemblies Section 4 with respect to the following:

• Facilities - Cleanliness and ambient environments in all work areas be

maintained at levels that prevent contamination or deterioration of tools,

materials, and surfaces to be soldered or conformally coated. Eating,

drinking, smoking, including use of e-cigarettes, and/or use of tobacco

products be prohibited in the work area.

• Environmental Controls - The soldering facility (controlled work area) be

enclosed, temperature and humidity controlled, and maintained at a posi-

tive pressure.

• Controlled Work Area (CWA) For the purpose of this statement, a Con-

trolled Work Area (CWA) is defined as an enclosed assembly / processing

area maintained to a high degree of shop cleanliness, environmental

control, and foreign object debris (FOD) mitigation, either by process or

procedure, to limit the entry of contamination.

If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

This equipment should be installed in accordance with the Installation Manual.

ASM absolves itself of all responsibility if the machine is not used within its

operating envelope or for its intended purpose.

TRANSPORTATION - MAJOR RELOCATION

MACHINE SUPPLIES AND ENVIRONMENTAL CONDITIONS

42.40 Technical Reference Manual Chapter Issue 5, Nov 19

Machine Footprints

Figure 42-8 Type 1 Covers

R0630.

Max dimension from

pivot point

360

1150

Transfer Height 960

980 max)

(840 min to

Side View (Right)

1345

( min to 13 2 max)1102 6

1106

(1352 min to 1492 max)

141

Front View

1913

(1 min to 1 max)834 974

1471.5

Plan View

606

Front of

board

1758

1334

Weight

Boxed - 8 kg, Unboxed - 6 kg10 60

(Dependent upon configured options

selected with the machine)

Note

All dimensions

in millimetres

Board transfer

height 8

- 980 mm40

Screen load height 925 - 1065