88192277-01-19 - Micron Technical Reference V9 Volume 4.pdf - 第301页

TRANSPORTATION - POWER UP FOREIGN MACHINE INTERFACE Chapter Issue 3, Nov 19 Technical Reference Manual 43.27 Figure 43-6 Multi-Interface Unit M1SK1 UPLINE M1SK2 DO W NLINE M1PL3 DEK M/C M1SK4 DEK USB +12V +24V +24V S W S…

100%1 / 310
TRANSPORTATION - POWER UP
FOREIGN MACHINE INTERFACE
43.26 Technical Reference Manual Chapter Issue 3, Nov 19
Multi-Interface Unit The DEK Multi-Interface Unit (MIU) is a communications interface that allows
the machine to communicate with upline and downline board handlers.
It simplifies the set up of the communications link between machines of different
manufacture by providing preprogrammed and programmable connections to
suit the interface protocol types commonly found within the board processing
industry.
The onboard, switch selectable, interface types are detailed later in this section.
Up to 16 interfaces can be specified for upline and downline handlers. The
upline machine can be of a different interface type to the downline machine.
Power supplies of +24V and +12V power the communications devices of the
upline and downline machines. Input signals to the MIU are opto-isolated.Relay
or open collector output driver signals are available for the MIU outputs.
A patching area routes patching link connections direct from upline to downline
as specified by any given protocol requirement.
TRANSPORTATION - POWER UP
FOREIGN MACHINE INTERFACE
Chapter Issue 3, Nov 19 Technical Reference Manual 43.27
Figure 43-6 Multi-Interface Unit
M1SK1
UPLINE
M1SK2
DOWNLINE
M1PL3
DEK M/C
M1SK4
DEK USB
+12V
+24V
+24V SW
SEND UPLINE
SEND DOWNLINE
CONTROL IN
UPLINE READY
DOWNLINE READY
CONTROL OUT
POWER
I/P'S
O/P'S
PROTOCOL SELECTION
UP
LINE
DOWN
LINE
MIU 191114
Protocol Selection
Upline interface select switch.
Downline interface select switch.
M1SK1
Signal lines to and from the DEK machine
from the upline machine.
4 Inputs: Opto-isolated.
4 Outputs: Lowside driver.
4 Outputs: Solid State Relay switched.
LED Bank LD1
Shows the
integrity of
the derived
supplies
LED Bank LD2
Indicates the
sequence of
events during
board transfers
(Inputs)
LED Bank LD3
Indicates the
sequence of
events during
board transfers
(Outputs)
M1SK2
Signal lines to and from
the DEK machine from
the downline machine.
4 Inputs: Opto-isolated.
4 Outputs: Lowside driver.
4 Outputs: Solid State
Relay switched.
DEK USB connection
not used.
M1SK4
M
1
S
K
1
M
1
S
K
1
U
P
L
I
N
E
U
P
L
I
N
E
M
1
S
K
2
M1SK
2
D
O
W
N
L
I
N
E
D
OW
NLI
N
E
M
1
P
L
3
M
1P
L
3
D
E
K
M
/
C
D
E
K
M
/
C
M
1
S
K
4
M
1S
K4
D
E
K
U
S
B
D
E
K
U
S
B
+
1
2
V
+1
2V
+
2
4
V
+
2
4V
+
2
4
V
S
W
+
24V
SW
S
E
N
D
U
P
L
I
N
E
SEN
D
U
PLI
N
E
S
E
N
D
D
O
W
N
L
I
N
E
SEN
D DOW
NLI
NE
C
O
N
T
R
O
L
I
N
CO
N
T
R
OL
I
N
U
P
L
I
N
E
R
E
A
D
Y
U
PLI
N
E
RE
A
DY
D
O
W
N
L
I
N
E
R
E
A
D
Y
D
O
W
N
LIN
E
REA
D
Y
C
O
N
T
R
O
L
O
U
T
CONT
RO
L
O
UT
P
O
W
E
R
P
OW
ER
I
/
P
'
SI
/
P
'
S
O
/
P
'
SO
/
P
'
S
PR
OT
OC
OL
SE
LE
C
T
I
O
N
PR
O
T
OC
O
L
S
E
L
EC
T
IO
N
U
P
U
P
L
I
N
E
L
I
NE
D
O
W
N
DO
W
N
L
I
N
E
L
INE
MI
U
19
1
1
14
MIU
191
1
14
4
8
0
4
8
0
M1PL3
Power supplies.
Comms connections to the DEK machine
Inputs to the DEK machine from interface -
1. Downline Ready
2. Upline Ready
3. Control In
Outputs from the DEK machine to interface -
1. Send Downline
2. Send Upline
3. Control Out
4
80
4
80
TRANSPORTATION - POWER UP
FOREIGN MACHINE INTERFACE
43.28 Technical Reference Manual Chapter Issue 3, Nov 19
Protocol Selection
Figure 43-7 Interface Selector Switches
Part Numbers &
Settings
Procedure Ensure the MIU is configured with the correct protocols for upline and downline
machines as detailed earlier.
With the cables supplied, connect the upline and downline machines to the MIU
box or FMI Pod. Cables should be routed down behind the rear access panel.
1. Power up the machine using the mains isolator.
2. Press the System button.
3. Select Maintenance.
4. Select Machine Setup.
5. Select Basics.
M1SK1
UPLINE
M1SK2
DOWNLINE
M1PL3
DEK M/C
M1SK4
DEK USB
+12V
+24V
+24V SW
SEND UPLINE
SEND DOWNLINE
CONTROLIN
UPLINE READY
DOWNLINE READY
CONTROL OUT
POWER
I/P'S
O/P'S
PROTOCOL SELECTION
UP
LINE
DOWN
LINE
MIU 191114
4
80
4
80
4
80
4
80
Upline Interface
Selector Switch (SW2)
Downline Interface
Selector Switch (SW3)
Protocol MIU Setting Cable Part Number
Upline SW2 Downline SW3 Upline Downline
SMEMA 2 2 88131343-01 88131345-01
Siemens 3 3 88131335-01 88131337-01
SMPI 4 4 88131331-01 88131333-01
TDK 5 5 88131323-01 88131325-01
Fuji 7 7 88126757-01 88126758-01
Panasonic 7 7 88131339-01 88131341-01
Sanyo 8 8 88146120-01 88146119-01