88192277-01-19 - Micron Technical Reference V9 Volume 4.pdf - 第25页
NETWORKING CONNECTION TO A NETW ORK SERVICE Chapter Issue 6, Nov 19 Technical Reference Manual 36.9 IP Address (GEM Only) The GEM - IP Address for the printer must be set up in the DekSECSII.cfg file, this can be checked…
NETWORKING
CONNECTION TO A NETWORK SERVICE
36.8 Technical Reference Manual Chapter Issue 6, Nov 19
7. If any changes were made, the printer needs to be rebooted before the
changes take effect.
NOTE
The network administrator should be instructed to create two working
directories for the product and data fields to be stored. These directories
must have read/write capabilities.
Selecting and
Editing Comms
Protocol Options
To select a Comms Protocol option carry out the following:
1. Select Maintenance.
2. Select Machine Setup.
3. Select Network.
4. Select Comms Protocol.
5. From the Comms Protocol window, select one of the following protocol
options:
•No Comms
•GEM
• Net File
6. Select Accept.
7. If Net File has been selected, the following parameters can be accessed and
edited:
• Printer Location
• Local Copies
• Product Directory
• Data Directory
• Remote Product Path
• Remote Data Path
NOTE
The Net File option may display a further window requesting the Network
Password.
8. If GEM has been selected, the following parameters can be accessed and
edited:
• Printer Location
• Product Directory
• Data Directory
9. Select Enable Comms, once the parameters are setup for the appropriate
protocol.
10. Select Back.
11. Select Back.
12. Select Back.
NETWORKING
CONNECTION TO A NETWORK SERVICE
Chapter Issue 6, Nov 19 Technical Reference Manual 36.9
IP Address (GEM
Only)
The GEM - IP Address for the printer must be set up in the DekSECSII.cfg file,
this can be checked and edited if necessary in the configuration file D:\Program
Files\DEK\Machine Control\Printer\DekSECSII.cfg.
Set the PASSIVE ENTITY IP ADDRESS to the printers’ ‘IP Address’.
If there is more than one printer communicating with the GEM Host, set the
DEVICEID differently for each printer. The default value is 0x109 (265). Alter-
native DEVICEID values should be chosen within the range 0x0000 - 0x7FFF
(0 - 32767).
NETWORKING
CONNECTION TO A NETWORK SERVICE
36.10 Technical Reference Manual Chapter Issue 6, Nov 19
Quick Reference
Table
The table below is provided for an engineer who needs a quick reference to the
actions required to install a printer onto a network. The engineer may have
previously installed a printer, be re-installing a printer onto another server or be
installing several printers at once.
NOTE
The system requires that the correct enabling security key device is fitted to the
port on the rear of the printer before software applications can be installed.
At the printer use housekeeping to transfer product files (.pr1) from local disk to
the remote disk. Load a product file from the remote disk back to the printer and
check that the transaction is complete.
No. Action Required Information
1 From the Windows desktop, right click My
Computer, select - Properties - Network
Identification - Properties to register the
printer on the correct domain or workgroup
The network administrator shall supply
domain or workgroup information
2 Select the Protocols tab, select TCP/IP
protocol and the Properties button
Check that the adaptor is correct for the
connection (as fitted in the PC) There
may be more than one device fitted
3 If DHCP is specified:- Select: Obtain an IP Address from the
DHCP Server
4 If an IP Address is to be specified:- Obtain the IP Address, and the Subnet
Mask details from the system adminis-
trator
5 Tell the network administrator that you
require two working directories where the
product and data files are to be stored
Files must have full administrative rights
(read/write)
6 For GEM, set up the IP address in the SDR
driver
D:\Program Files\DEK\Machine Con-
trol\Printer\sdrconf.cfg
Set the Passive IP Address to the Print-
ers’ IP Address
7 If more than one printer is to communicate
using the GEM Host:
Set a different DEVICEID for each
printer.
8 Select Local Copies option Decide if it is desired that the printer
copies remote product files to the local
drive after loading it from the remote
product directory. If disabled, modifica-
tions to the file are not saved locally
9 Check the physical connection to the net-
work
Ethernet 10 Base T is supported by
ASM
10 Ask the network administrator if there are
any intermediate routers between the server
and the printing machine
Supply the correct IP Address, check
the IP forwarding option in Protocols
Properties, Routing
11 Using My Network Places in Windows,
check that the printer can be ‘seen’ by the
host PC
Look for a computer icon with the printer
serial number next to it - DEK_******
12 Test the network connection See section ‘Pinging the Network’