00196693-03_UM_SX4DX4_SR706_EN.pdf - 第182页
3 Technical data and assemblies User Manual SIPLACE SX4/DX4 3.10 Component trolleys on the SIPLACE SX4 From software version SC.706.xx Version 06/2012 EN 182 3 Fig. 3.10 - 7 SIPLACE X series changeover table, front view …
User Manual SIPLACE SX4/DX4 3 Technical data and assemblies
From software version SC.706.xx Version 06/2012 EN 3.10 Component trolleys on the SIPLACE SX4
181
3.10.6 SIPLACE X series changeover table
The front slider guides of the feeder modules are placed on the insertion aid (item 1 in fig.
3.10 - 6
). When pushed in, the slider guides of the
feeder module (item 12 and 13 in fig. 3.9 - 2
, page 151) slide on the guide profile (item 2 in fig.
3.10 - 6
) up to the stop rail (item 4 in fig. 3.10 - 6). A centering hole (item 5 in fig. 3.10 - 6) on the
stop rail accommodates the X feeder module centering pin "front" (item 4 in fig. 3.9 - 1
, page 150).
At the same time, the changeover table locking latch (item 1 in fig. 3.10 - 7
, page 182) engages
onto the locking roller (item 1 in fig. 3.9 - 1
, page 150) of the feeder module. The centering pin
"rear" (item 12 in fig. 3.9 - 1
, page 150) on the upper side of the feeder module is accommodated
by the recess in the centering bar (item 3 in fig. 3.10 - 6
).
3
Fig. 3.10 - 6 Changeover table, SIPLACE X series, rear view
(1) Insertion aid
(2) Guide profile ( profile)
(3) Centering bar for holding the "back" centering pin for X feeder modules
(4) Stop bar
(5) Centering holes
(6) Contact for switching the safety switch of the EMERGENCY STOP circuit
(7) Hand guard
3 Technical data and assemblies User Manual SIPLACE SX4/DX4
3.10 Component trolleys on the SIPLACE SX4 From software version SC.706.xx Version 06/2012 EN
182
3
Fig. 3.10 - 7 SIPLACE X series changeover table, front view
(1) Locking latches
(2) Centering pin on the changeover table
(3) compressed air coupling
(4) Earthing (ground) pin
(5) Centering hole on the changeover table
User Manual SIPLACE SX4/DX4 3 Technical data and assemblies
From software version SC.706.xx Version 06/2012 EN 3.10 Component trolleys on the SIPLACE SX4
183
3.10.7 Mount for the additional tape reel
3
Fig. 3.10 - 8 Mount for additional tape reel (X series)
(1) Mount for the additional tape reel, item no. 00141217-xx
(2) Mounting device for the support
X series feeder modules can process component tapes without problems if the lateral offset be-
tween the feeder module and the tape reel does not exceed 60 mm. If a predefined setup means
that the maximum permitted offset cannot be maintained, we recommend that you use the mount
for an additional tape reel (item 1). Simply insert the mount into the holder (item 2) and push it until
the offset is less than the maximum permitted value of 60 mm. The component trolley has 5 hold-
ers in total. Each tape reel mount can hold 2 tape reels, which means that up to ten 15" (381 mm)
reels can be positioned above the tape container.
max. 60 mm