00196693-03_UM_SX4DX4_SR706_EN.pdf - 第275页
User Manual SIPLACE SX4/DX4 5 Working with the machine From software version SC.706.xx Version 06/2012 EN 5.10 Setting up the feeder modules 275 Shorten the component t ape with the now ex posed component pockets by ar…
5 Working with the machine User Manual SIPLACE SX4/DX4
5.10 Setting up the feeder modules From software version SC.706.xx Version 06/2012 EN
274
Check the "back" centering pin (item 3 in fig. 5.10 - 3, page 273) of the feeder module as you
do so. This must slide easily into the recess (item 5) in the centering bar, otherwise the feeder
module is not seated vertically on the changeover table or it was not placed on the guide pro-
file (item 8 in fig. 5.10 - 3
, page 273) correctly.
When the feeder module is at the stop position, the locking latch (item 7 in fig. 5.10 - 3, page
273
) latches onto the locking roller of the feeder module (item 1 in fig. 3.9 - 1, page 150). If you
have forgotten to engage the removal handle (item 1 in fig. 5.10 - 2
, page 272) the status dis-
play
on the feeder module's operator panel will light up red after a few seconds. The LCD display
contains the error message "Handle --->>" (see fig. 5.11 - 1
, page 280).
Engage the removal handle (item 1 in fig. 5.10 - 2, page 272). The feeder module's status
display now lights up green and the feeder module is on standby. The track number and
conveyor increment can be read on the LCD display once more.
5.10.4 Placing the component tape on the X feeder module (8 -88 mm)
5.10.4.1 Checking the X tape feeder module
When you place the component tape in the feeder module, first check whether there are
any components in the vicinity of the pickup window (item 2 in fig. 5.10 - 5
, page 276).
Remove any components that you find since they could cause a fault.
5.10.4.2 Preparing the component tape for insertion
Check that there is a straight cut edge at the start of the component tape.
If the transport holes are torn or bent, cut off this part of the tape.
Also make sure that there are no streaks of adhesive on the cover foil.
Pull around 30 cm cover foil away from the component tape if this does not expose any
components.
PLEASE NOTE 5
Use an SMD tape threader if there is insufficient cover foil available to make sure that no com-
ponents
are lost:
for the 8 mm - tape: Item no. 00355265-xx
for the 12 mm - tape: Item no. 00356342-xx
User Manual SIPLACE SX4/DX4 5 Working with the machine
From software version SC.706.xx Version 06/2012 EN 5.10 Setting up the feeder modules
275
Shorten the component tape with the now exposed component pockets by around 3 cm.
Remove the components from the open tape pockets.
Wrap the cover foil around the front edge of the tape along the bottom of the tape.
5.10.4.3 Placing tape on the X feeder module
5
Fig. 5.10 - 4 Inserting the component tape
(1) Entry to the tape guide channel
(2) Operator panel
(3) Exit from the tape guide channel
(4) Pickup window
(5) Lever for raising the pick-up window
5
Hold the component tape so that the transport holes are on the left-hand side viewed in the
direction of travel.
Push the component tape into the entry (item 1 in fig. 5.10 - 4) to the tape guide channel and
further until it emerges from the exit opening (item 3 in fig. 5.10 - 4
).
Pull the component tape up and out, and fold the cover foil back against the top of the tape.
5 Working with the machine User Manual SIPLACE SX4/DX4
5.10 Setting up the feeder modules From software version SC.706.xx Version 06/2012 EN
276
Guide the start of the tape beneath the pickup window (item 2 in fig. 5.10 - 5) and further until
the component tape is touching the sprocket wheel.
5
Fig. 5.10 - 5 Pickup window on the tape feeder module
(1) Tape support, removable (see section 5.10.4.4, page 278)
(2) Pickup window
(3) Removal edge for the cover foil
(4) Component pick-up area
(5) Lever for raising and latching the pick-up window
On the operator panel, press the FORWARD button (item 1 in fig. 5.10 - 6) until the bend of
the cover foil is in the component pickup area (item 4 in fig. 5.10 - 5
).
5
Fig. 5.10 - 6 Operator panel of the 8 mm feeder module
(1) FORWARD button for moving the component tape forward
(2) BACK button for moving the component tape back
(3) FOIL button for tensioning the cover foil