00196693-03_UM_SX4DX4_SR706_EN.pdf - 第196页

4 Setting up and commissioning User Manual SIPLACE SX4/DX4 4.1 Transportation and Delivery Configuration F rom software version SC.706.xx Version 06/2012 EN 196 4.1.5.2 Means of transport Use a fork-lift truck with the f…

User Manual SIPLACE SX4/DX4 4 Setting up and commissioning

From software version SC.706.xx Version 06/2012 EN 4.1 Transportation and Delivery Configuration

195

4.1.4.4 Fork-lift attachment points on the transport crate or pallet

Position the fork-lift truck only at the points marked (A). in fig. 4.1 - 1, page 189. We recommend

that you keep the crate or the pallet with packaging for later use.

WARNING 4

If you still decide to transport the machine without a crate or pallet, you MUST follow the instruc-

tions in the next section to avoid serious damage to your machine.

4.1.5 Transporting the machine without a crate or pallet

4.1.5.1 Safety instructions

WARNING 4

 The applicable accident prevention regulations concerning the transportation of heavy goods

must be followed.

 In particular, you should wear safety boots to minimize the risk of crushing your feet.

 Read this section in full before transporting the machine to avoid severe damage.

 When you are transporting the machine, make sure that all the feet are clear of the floor. If

they are not clear, the feet will drag along the floor and bump into obstacles. This could dam-

age the machine foot thread in the machine frame.

4 Setting up and commissioning User Manual SIPLACE SX4/DX4

4.1 Transportation and Delivery Configuration From software version SC.706.xx Version 06/2012 EN

196

4.1.5.2 Means of transport

Use a fork-lift truck with the following specification to carry the machine:

4.1.5.3 Fork-lift attachment points on the machine

The diagram 4.1 - 4, page 197 shows the fork lift attachment points on the machine for lifting the

machine off the pallet or transporting it without the pallet.

PLEASE NOTE 4

Always use a pallet and fork-lift to transport the machine over longer distances in order to avoid

damaging the machine.

WARNING 4

Please note the following points before you raise the machine in order to avoid irreversible dam-

age to the machine:

– The forks must be aligned parallel to the PCB conveyor.

– The forks must be aligned to the center of the machine.

– The forks may only be opened to a degree which ensures that they are still within the contact

area of the machine underside (see fig. 4.1 - 4

, page 197).

– Do not increase the distance between the forks so that the machine is lifted outside this con-

tact surface. This would lead to deformation of the machine frame and/or damage to the ca-

bles and leads.

 Make sure that the forks are evenly loaded when you lift the machine. A firm support between

the forks and machine will prevent the machine tilting when it is raised. This will also prevent

a one-sided load on the machine feet, which would deform the fixing of the machine feet. We

recommend that a second person watch the machine as it is raised, and make sure that the

machine does not tip to one side when lifted with the fork-lift.

Fork length min. 1800 mm

Lifting power min. 6000 kg

Distance between forks with the forks running parallel

to the direction of PCB transport

Approx. 420 mm

User Manual SIPLACE SX4/DX4 4 Setting up and commissioning

From software version SC.706.xx Version 06/2012 EN 4.1 Transportation and Delivery Configuration

197

Fig. 4.1 - 4 Contact surfaces - forks parallel to the direction of PCB transport (example of SX4)

(1) Contact surface for fork lift truck forks

4.1.5.4 Points that MUST be noted when transporting the machine

WARNING 4

When you are transporting the machine, make sure that all the feet are clear of the floor. If they

are not clear, the feet will drag along the floor or bump into obstacles. This could damage the

machine feet and/or the foot fixtures.

(1)